TS 136 141 - V10.1.0 - LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) conformance testing (3GPP TS 36.141 version 10.1.0 Release 10)

1.1 MB·English

by  European Telecommunications Standards Institute

ETSI TS 136 141
V10.1.0
(2011-01)
Technical Specification

LTE;
Evolved Universal Terrestrial Radio Access (E-UTRA);
Base Station (BS) conformance testing
(3GPP TS 36.141 version 10.1.0 Release 10)
3GPP TS 36.141 version 10.1.0 Release 10 1 ETSI TS 136 141 V10.1.0 (2011-01)

Reference
RTS/TSGR-0436141va10
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone] Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2011.
All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM, TIPHONTM, the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 2 ETSI TS 136 141 V10.1.0 (2011-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
http://webapp.etsi.org/key/queryform.asp.
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 3 ETSI TS 136 141 V10.1.0 (2011-01)
Contents
Intellectual Property Rights ................................................................................................................................ 2
Foreword ............................................................................................................................................................. 2
Foreword ........................................................................................................................................................... 11
1 Scope ...................................................................................................................................................... 12
2 References .............................................................................................................................................. 12
3 Definitions, symbols and abbreviations ................................................................................................. 13

3.1 Definitions ........................................................................................................................................................ 13

3.2 Symbols ............................................................................................................................................................ 14

3.3 Abbreviations ................................................................................................................................................... 15
4 General test conditions and declarations ................................................................................................ 16

4.1 Measurement uncertainties and Test Requirements ......................................................................................... 16

4.1.1 General ........................................................................................................................................................ 16

4.1.2 Acceptable uncertainty of Test System ....................................................................................................... 17

4.1.2.1 Measurement of transmitter .................................................................................................................. 18

4.1.2.2 Measurement of receiver ....................................................................................................................... 18

4.1.2.3 Measurement of performance requirement ........................................................................................... 22

4.1.3 Interpretation of measurement results ......................................................................................................... 24

4.2 Base station classes .......................................................................................................................................... 24

4.3 Regional requirements ...................................................................................................................................... 25

4.4 Selection of configurations for testing.............................................................................................................. 27

4.5 BS Configurations ............................................................................................................................................ 27

4.5.1 Transmit configurations .............................................................................................................................. 27

4.5.1.1 Transmit diversity and MIMO transmission ......................................................................................... 27

4.5.2 Receive configurations ............................................................................................................................... 27

4.5.2.1 Receiver diversity ................................................................................................................................. 28

4.5.3 Duplexers .................................................................................................................................................... 28

4.5.4 Power supply options .................................................................................................................................. 28

4.5.5 Ancillary RF amplifiers .............................................................................................................................. 29

4.5.6 BS with integrated Iuant BS modem .......................................................................................................... 29

4.5.7 BS using antenna arrays .............................................................................................................................. 29

4.5.7.1 Receiver tests ........................................................................................................................................ 30

4.5.7.2 Transmitter tests .................................................................................................................................... 30

4.6 Manufacturer"s declarations of regional and optional requirements ................................................................ 31

4.6.1 Operating band and frequency range .......................................................................................................... 31

4.6.2 Channel bandwidth ..................................................................................................................................... 31

4.6.3 Base station output power ........................................................................................................................... 31

4.6.4 Spurious emissions Category ...................................................................................................................... 31

4.6.5 Additional operating band unwanted emissions ......................................................................................... 31

4.6.6 Co-existence with other systems ................................................................................................................. 32

4.6.7 Co-location with other base stations ........................................................................................................... 32

4.7 Specified frequency range and supported channel bandwidth .......................................................................... 32

4.8 Format and interpretation of tests ..................................................................................................................... 33
5 Operating bands and channel arrangement ............................................................................................. 34

5.1 General ............................................................................................................................................................. 34

5.2 Void .................................................................................................................................................................. 34

5.3 Void .................................................................................................................................................................. 34

5.4 Void .................................................................................................................................................................. 34

5.5 Operating bands ................................................................................................................................................ 34

5.6 Channel bandwidth ........................................................................................................................................... 35

5.7 Channel arrangement ........................................................................................................................................ 36

5.7.1 Channel spacing .......................................................................................................................................... 36

5.7.2 Channel raster ............................................................................................................................................. 36

5.7.3 Carrier frequency and EARFCN ................................................................................................................. 36
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 4 ETSI TS 136 141 V10.1.0 (2011-01)
6 Transmitter characteristics ..................................................................................................................... 38

6.1 General ............................................................................................................................................................. 38

6.1.1 E-UTRA Test Models ........................................................................................................................... 38

6.1.1.1 E-UTRA Test Model 1.1 (E-TM1.1)..................................................................................................... 38

6.1.1.2 E-UTRA Test Model 1.2 (E-TM1.2)..................................................................................................... 39

6.1.1.3 E-UTRA Test Model 2 (E-TM2) .......................................................................................................... 42

6.1.1.4 E-UTRA Test Model 3.1 (E-TM3.1)..................................................................................................... 43

6.1.1.5 E-UTRA Test Model 3.2 (E-TM3.2)..................................................................................................... 44

6.1.1.6 E-UTRA Test Model 3.3 (E-TM3.3)..................................................................................................... 47

6.1.2 Data content of Physical channels and Signals ........................................................................................... 50

6.1.2.1 Reference signals .................................................................................................................................. 50

6.1.2.2 Primary Synchronization signal ............................................................................................................ 50

6.1.2.3 Secondary Synchronization signal ........................................................................................................ 50

6.1.2.4 PBCH .................................................................................................................................................... 50

6.1.2.5 PCFICH ................................................................................................................................................. 50

6.1.2.6 PHICH ................................................................................................................................................... 50

6.1.2.7 PDCCH ................................................................................................................................................. 51

6.1.2.8 PDSCH .................................................................................................................................................. 51

6.2 Base station output power ................................................................................................................................ 51

6.2.1 Definition and applicability ........................................................................................................................ 51

6.2.2 Minimum Requirement ............................................................................................................................... 52

6.2.3 Test purpose ................................................................................................................................................ 52

6.2.4 Method of test ............................................................................................................................................. 52

6.2.4.1 Initial conditions ................................................................................................................................... 52

6.2.4.2 Procedure .............................................................................................................................................. 52

6.2.5 Test Requirements ...................................................................................................................................... 53

6.2.6 Home BS output power for adjacent UTRA channel protection................................................................. 53

6.2.6.1 Definition and applicability ................................................................................................................... 53

6.2.6.2 Minimum Requirement ......................................................................................................................... 54

6.2.6.3 Test purpose .......................................................................................................................................... 54

6.2.6.4 Method of test ....................................................................................................................................... 54

6.2.6.4.1 Initial conditions .............................................................................................................................. 54

6.2.6.4.2 Procedure ......................................................................................................................................... 54

6.2.6.5 Test Requirements ................................................................................................................................. 55

6.2.7 Home BS output power for adjacent E-UTRA channel protection ............................................................. 55

6.2.7.1 Definition and applicability ................................................................................................................... 55

6.2.7.2 Minimum Requirement ......................................................................................................................... 56

6.2.7.3 Test purpose .......................................................................................................................................... 56

6.2.7.4 Method of test ....................................................................................................................................... 56

6.2.7.4.1 Initial conditions .............................................................................................................................. 56

6.2.7.4.2 Procedure ......................................................................................................................................... 56

6.2.7.5 Test Requirements ................................................................................................................................. 57

6.3 Output power dynamics .................................................................................................................................... 57

6.3.1 RE Power control dynamic range ............................................................................................................... 57

6.3.1.1 Definition and applicability ................................................................................................................... 57

6.3.1.2 Minimum Requirement ......................................................................................................................... 58

6.3.1.3 Method of test ....................................................................................................................................... 58

6.3.2 Total power dynamic range ........................................................................................................................ 58

6.3.2.1 Definition and applicability ................................................................................................................... 58

6.3.2.2 Minimum Requirement ......................................................................................................................... 58

6.3.2.3 Test purpose .......................................................................................................................................... 58

6.3.2.4 Method of test ....................................................................................................................................... 58

6.3.2.4.1 Initial conditions .............................................................................................................................. 58

6.3.2.4.2 Procedure ......................................................................................................................................... 58

6.3.2.5 Test Requirement .................................................................................................................................. 58

6.4 Transmit ON/OFF power ................................................................................................................................. 59

6.4.1 Transmitter OFF power .............................................................................................................................. 59

6.4.1.1 Definition and applicability ................................................................................................................... 59

6.4.1.2 Minimum Requirement ......................................................................................................................... 59

6.4.1.3 Test purpose .......................................................................................................................................... 59

6.4.1.4 Method of test ....................................................................................................................................... 59

6.4.1.4.1 Void ................................................................................................................................................. 59
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 5 ETSI TS 136 141 V10.1.0 (2011-01)

6.4.1.4.2 Void ................................................................................................................................................. 59

6.4.1.5 Test requirement ................................................................................................................................... 59

6.4.2 Transmitter transient period ........................................................................................................................ 60

6.4.2.1 Definition and applicability ................................................................................................................... 60

6.4.2.2 Minimum Requirement ......................................................................................................................... 60

6.4.2.3 Test purpose .......................................................................................................................................... 60

6.4.2.4 Method of test ....................................................................................................................................... 60

6.4.2.4.1 Initial conditions .............................................................................................................................. 60

6.4.2.4.2 Procedure ......................................................................................................................................... 60

6.4.2.5 Test requirement ................................................................................................................................... 61

6.5 Transmitted signal quality ................................................................................................................................ 61

6.5.1 Frequency error ........................................................................................................................................... 61

6.5.1.1 Definition and applicability ................................................................................................................... 61

6.5.1.2 Minimum Requirement ......................................................................................................................... 61

6.5.1.3 Test purpose .......................................................................................................................................... 61

6.5.1.4 Method of test ....................................................................................................................................... 61

6.5.1.5 Test requirement ................................................................................................................................... 61

6.5.2 Error Vector Magnitude .............................................................................................................................. 62

6.5.2.1 Definition and applicability ................................................................................................................... 62

6.5.2.2 Minimum Requirement ......................................................................................................................... 62

6.5.2.3 Test purpose .......................................................................................................................................... 62

6.5.2.4 Method of test ....................................................................................................................................... 62

6.5.2.4.1 Initial conditions .............................................................................................................................. 62

6.5.2.4.2 Procedure ......................................................................................................................................... 62

6.5.2.5 Test requirement ................................................................................................................................... 62

6.5.3 Time alignment between transmitter branches ........................................................................................... 63

6.5.3.1 Definition and applicability ................................................................................................................... 63

6.5.3.2 Minimum Requirement ......................................................................................................................... 63

6.5.3.3 Test Purpose .......................................................................................................................................... 63

6.5.3.4 Method of Test ...................................................................................................................................... 63

6.5.3.4.1 Initial Conditions ............................................................................................................................. 63

6.5.3.4.2 Procedure ......................................................................................................................................... 63

6.5.3.5 Test Requirement .................................................................................................................................. 64

6.5.4 DL RS power .............................................................................................................................................. 64

6.5.4.1 Definition and applicability ................................................................................................................... 64

6.5.4.2 Minimum Requirement ......................................................................................................................... 64

6.5.4.3 Test purpose .......................................................................................................................................... 64

6.5.4.4 Method of test ....................................................................................................................................... 64

6.5.4.4.1 Initial conditions .............................................................................................................................. 64

6.5.4.4.2 Procedure ......................................................................................................................................... 64

6.5.4.5 Test requirement ................................................................................................................................... 64

6.6 Unwanted emissions ......................................................................................................................................... 64

6.6.1 Occupied bandwidth ................................................................................................................................... 65

6.6.1.1 Definition and applicability ................................................................................................................... 65

6.6.1.2 Minimum Requirements ........................................................................................................................ 65

6.6.1.3 Test purpose .......................................................................................................................................... 65

6.6.1.4 Method of test ....................................................................................................................................... 65

6.6.1.4.1 Initial conditions .............................................................................................................................. 65

6.6.1.4.2 Procedure ......................................................................................................................................... 65

6.6.1.5 Test requirements .................................................................................................................................. 66

6.6.2 Adjacent Channel Leakage power Ratio (ACLR) ...................................................................................... 66

6.6.2.1 Definition and applicability ................................................................................................................... 66

6.6.2.2 Minimum Requirement ......................................................................................................................... 66

6.6.2.3 Test purpose .......................................................................................................................................... 66

6.6.2.4 Method of test ....................................................................................................................................... 66

6.6.2.4.1 Initial conditions .............................................................................................................................. 66

6.6.2.4.2 Procedure ......................................................................................................................................... 67

6.6.2.5 Test Requirement .................................................................................................................................. 67

6.6.3 Operating band unwanted emissions .......................................................................................................... 68

6.6.3.1 Definition and applicability ................................................................................................................... 68

6.6.3.2 Minimum Requirement ......................................................................................................................... 69

6.6.3.3 Test purpose .......................................................................................................................................... 69
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 6 ETSI TS 136 141 V10.1.0 (2011-01)

6.6.3.4 Method of test ....................................................................................................................................... 69

6.6.3.4.1 Initial conditions .............................................................................................................................. 69

6.6.3.4.2 Procedure ......................................................................................................................................... 69

6.6.3.5 Test requirement ................................................................................................................................... 70

6.6.3.5.1 Test requirements for Wide Area BS (Category A)......................................................................... 70

6.6.3.5.2 Test requirements for Wide Area BS (Category B) ......................................................................... 72

6.6.3.5.2.1 Category B test requirements (Option 1) ......................................................................................... 72

6.6.3.5.2.2 Category B (Option 2) ..................................................................................................................... 74

6.6.3.5.2A Test requirements for Local Area BS (Category A and B) .............................................................. 75

6.6.3.5.2X Test requirements for Home BS (Category A and B) ...................................................................... 76

6.6.3.5.3 Additional requirements .................................................................................................................. 77

6.6.4 Transmitter spurious emissions ................................................................................................................... 78

6.6.4.1 Definition and applicability ................................................................................................................... 78

6.6.4.2 Minimum Requirements ........................................................................................................................ 79

6.6.4.3 Test Purpose .......................................................................................................................................... 79

6.6.4.4 Method of Test ...................................................................................................................................... 79

6.6.4.4.1 Initial conditions .............................................................................................................................. 79

6.6.4.4.2 Procedure ......................................................................................................................................... 79

6.6.4.5 Test requirements .................................................................................................................................. 79

6.6.4.5.1 Spurious emissions (Category A) .................................................................................................... 80

6.6.4.5.2 Spurious emissions (Category B) .................................................................................................... 80

6.6.4.5.3 Protection of the BS receiver of own or different BS ...................................................................... 80

6.6.4.5.4 Co-existence with other systems in the same geographical area ..................................................... 81

6.6.4.5.5 Co-location with other base stations ................................................................................................ 87

6.7 Transmitter intermodulation ............................................................................................................................. 91

6.7.1 Definition and applicability ........................................................................................................................ 91

6.7.2 Minimum Requirement ............................................................................................................................... 92

6.7.3 Test purpose ................................................................................................................................................ 92

6.7.4 Method of test ............................................................................................................................................. 92

6.7.4.1 Initial conditions ................................................................................................................................... 92

6.7.4.2 Procedures ............................................................................................................................................. 92

6.7.5 Test Requirements ...................................................................................................................................... 92
7 Receiver characteristics .......................................................................................................................... 94

7.1 General ............................................................................................................................................................. 94

7.2 Reference sensitivity level ................................................................................................................................ 94

7.2.1 Definition and applicability ........................................................................................................................ 94

7.2.2 Minimum Requirement ............................................................................................................................... 94

7.2.3 Test purpose ................................................................................................................................................ 94

7.2.4 Method of testing ........................................................................................................................................ 94

7.2.4.1 Initial conditions ................................................................................................................................... 94

7.2.4.2 Procedure .............................................................................................................................................. 94

7.2.5 Test requirement ......................................................................................................................................... 95

7.3 Dynamic range ................................................................................................................................................. 96

7.3.1 Definition and applicability ........................................................................................................................ 96

7.3.2 Minimum Requirement ............................................................................................................................... 96

7.3.3 Test purpose ................................................................................................................................................ 96

7.3.4 Method of testing ........................................................................................................................................ 96

7.3.4.1 Initial conditions ................................................................................................................................... 96

7.3.4.2 Procedure .............................................................................................................................................. 96

7.3.5 Test Requirements ...................................................................................................................................... 96

7.4 In-channel selectivity ....................................................................................................................................... 98

7.4.1 Definition and applicability ........................................................................................................................ 98

7.4.2 Minimum Requirement ............................................................................................................................... 99

7.4.3 Test purpose ................................................................................................................................................ 99

7.4.4 Method of testing ........................................................................................................................................ 99

7.4.4.1 Initial conditions ................................................................................................................................... 99

7.4.4.2 Procedure .............................................................................................................................................. 99

7.4.5 Test Requirements .................................................................................................................................... 100

7.5 Adjacent Channel Selectivity (ACS) and narrow-band blocking ................................................................... 101

7.5.1 Definition and applicability ...................................................................................................................... 101

7.5.2 Minimum Requirement ............................................................................................................................. 101
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 7 ETSI TS 136 141 V10.1.0 (2011-01)

7.5.3 Test purpose .............................................................................................................................................. 102

7.5.4 Method of test ........................................................................................................................................... 102

7.5.4.1 Initial conditions ................................................................................................................................. 102

7.5.4.2 Procedure for Adjacent Channel Selectivity ....................................................................................... 102

7.5.4.3 Procedure for narrow-band blocking ................................................................................................... 102

7.5.5 Test Requirements .................................................................................................................................... 102

7.6 Blocking ......................................................................................................................................................... 105

7.6.1 Definition and applicability ...................................................................................................................... 105

7.6.2 Minimum Requirements ........................................................................................................................... 105

7.6.3 Test purpose .............................................................................................................................................. 105

7.6.4 Method of test ........................................................................................................................................... 105

7.6.4.1 Initial conditions ................................................................................................................................. 105

7.6.4.2 Procedure ............................................................................................................................................ 106

7.6.5 Test Requirements .................................................................................................................................... 107

7.6.5.1 General requirement ............................................................................................................................ 107

7.6.5.2 Co-location with other base stations ................................................................................................... 110

7.7 Receiver spurious emissions........................................................................................................................... 114

7.7.1 Definition and applicability ...................................................................................................................... 114

7.7.2 Minimum Requirements ........................................................................................................................... 114

7.7.3 Test purpose .............................................................................................................................................. 114

7.7.4 Method of test ........................................................................................................................................... 114

7.7.4.1 Initial conditions ................................................................................................................................. 114

7.7.4.2 Procedure ............................................................................................................................................ 114

7.7.5 Test requirements ...................................................................................................................................... 115

7.8 Receiver intermodulation ............................................................................................................................... 115

7.8.1 Definition and applicability ...................................................................................................................... 115

7.8.2 Minimum Requirement ............................................................................................................................. 115

7.8.3 Test purpose .............................................................................................................................................. 115

7.8.4 Method of test ........................................................................................................................................... 116

7.8.4.1 Initial conditions ................................................................................................................................. 116

7.8.4.2 Procedures ........................................................................................................................................... 116

7.8.5 Test requirements ...................................................................................................................................... 117
8 Performance requirement ..................................................................................................................... 121

8.1 General ........................................................................................................................................................... 121

8.2 Performance requirements for PUSCH .......................................................................................................... 121

8.2.1 Performance requirements of PUSCH in multipath fading propagation conditions ................................. 121

8.2.1.1 Definition and applicability ................................................................................................................. 121

8.2.1.2 Minimum Requirement ....................................................................................................................... 121

8.2.1.3 Test Purpose ........................................................................................................................................ 121

8.2.1.4 Method of test ..................................................................................................................................... 121

8.2.1.4.1 Initial Conditions ........................................................................................................................... 121

8.2.1.4.2 Procedure ....................................................................................................................................... 122

8.2.1.5 Test Requirement ................................................................................................................................ 122

8.2.2 Performance requirements for UL timing adjustment............................................................................... 128

8.2.2.1 Definition and applicability ................................................................................................................. 128

8.2.2.2 Minimum Requirement ....................................................................................................................... 129

8.2.2.3 Test Purpose ........................................................................................................................................ 129

8.2.2.4 Method of test ..................................................................................................................................... 129

8.2.2.4.1 Initial Conditions ........................................................................................................................... 129

8.2.2.4.2 Procedure ....................................................................................................................................... 129

8.2.2.5 Test Requirement ................................................................................................................................ 130

8.2.3 Performance requirements for HARQ-ACK multiplexed on PUSCH ...................................................... 131

8.2.3.1 Definition and applicability ................................................................................................................. 131

8.2.3.2 Minimum Requirement ....................................................................................................................... 131

8.2.3.3 Test Purpose ........................................................................................................................................ 131

8.2.3.4 Method of test ..................................................................................................................................... 131

8.2.3.4.1 Initial Conditions ........................................................................................................................... 131

8.2.3.4.2 Procedure ....................................................................................................................................... 131

8.2.3.5 Test Requirement ................................................................................................................................ 132

8.2.4 Performance requirements for High Speed Train conditions .................................................................... 133

8.2.4.1 Definition and applicability ................................................................................................................. 133
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 8 ETSI TS 136 141 V10.1.0 (2011-01)

8.2.4.2 Minimum Requirement ....................................................................................................................... 133

8.2.4.3 Test Purpose ........................................................................................................................................ 133

8.2.4.4 Method of test ..................................................................................................................................... 134

8.2.4.4.1 Initial Conditions ........................................................................................................................... 134

8.2.4.4.2 Procedure ....................................................................................................................................... 134

8.2.4.5 Test Requirement ................................................................................................................................ 135

8.3 Performance requirements for PUCCH .......................................................................................................... 135

8.3.1 ACK missed detection for single user PUCCH format 1a ........................................................................ 135

8.3.1.1 Definition and applicability ................................................................................................................. 135

8.3.1.2 Minimum Requirement ....................................................................................................................... 136

8.3.1.3 Test purpose ........................................................................................................................................ 136

8.3.1.4 Method of test ..................................................................................................................................... 136

8.3.1.4.1 Initial Conditions ........................................................................................................................... 136

8.3.1.4.2 Procedure ....................................................................................................................................... 136

8.3.1.5 Test Requirement ................................................................................................................................ 137

8.3.2 CQI performance requirements for PUCCH format 2 .............................................................................. 137

8.3.2.1 Definition and applicability ................................................................................................................. 137

8.3.2.2 Minimum Requirement ....................................................................................................................... 137

8.3.2.3 Test purpose ........................................................................................................................................ 137

8.3.2.4 Method of test ..................................................................................................................................... 137

8.3.2.4.1 Initial Conditions ........................................................................................................................... 137

8.3.2.4.2 Procedure ....................................................................................................................................... 138

8.3.2.5 Test Requirement ................................................................................................................................ 138

8.3.3 ACK missed detection for multi user PUCCH format 1a ......................................................................... 138

8.3.3.1 Definition and applicability ................................................................................................................. 138

8.3.3.2 Minimum Requirement ....................................................................................................................... 139

8.3.3.3 Test purpose ........................................................................................................................................ 139

8.3.3.4 Method of test ..................................................................................................................................... 139

8.3.3.4.1 Initial Conditions ........................................................................................................................... 139

8.3.3.4.2 Procedure ....................................................................................................................................... 139

8.3.3.5 Test Requirement ................................................................................................................................ 140

8.4 Performance requirements for PRACH .......................................................................................................... 140

8.4.1 PRACH false alarm probability and missed detection .............................................................................. 140

8.4.1.1 Definition and applicability ................................................................................................................. 140

8.4.1.2 Minimum Requirement ....................................................................................................................... 141

8.4.1.3 Test purpose ........................................................................................................................................ 141

8.4.1.4 Method of test ..................................................................................................................................... 141

8.4.1.4.1 Initial Conditions ........................................................................................................................... 141

8.4.1.4.2 Procedure ....................................................................................................................................... 141

8.4.1.5 Test Requirement ................................................................................................................................ 142
Annex A (normative): Reference Measurement channels .............................................................. 143
A.0 General ................................................................................................................................................. 143
A.1 Fixed Reference Channels for reference sensitivity and in--channel selectivity (QPSK, R=1/3) ........ 143
A.2 Fixed Reference Channels for dynamic range (16QAM, R=2/3) ......................................................... 144
A.3 Fixed Reference Channels for performance requirements (QPSK 1/3) ............................................... 144
A.4 Fixed Reference Channels for performance requirements (16QAM 3/4) ............................................ 145
A.5 Fixed Reference Channels for performance requirements (64QAM 5/6) ............................................ 145
A.6 PRACH Test preambles ....................................................................................................................... 145
A.7 Fixed Reference Channels for UL timing adjustment (Scenario 1) ..................................................... 146
A.8 Fixed Reference Channels for UL timing adjustment (Scenario 2) ..................................................... 146
A.9 Multi user PUCCH test......................................................................................................................... 147
Annex B (normative): Propagation conditions ................................................................................ 148
B.1 Static propagation condition ................................................................................................................. 148
ETSI
3GPP TS 36.141 version 10.1.0 Release 10 9 ETSI TS 136 141 V10.1.0 (2011-01)
B.2 Multi-path fading propagation conditions ............................................................................................ 148

B.3 High speed train condition.............................................................................................................................. 149
B.4 Moving propagation conditions ............................................................................................................ 150
Annex C (normative): Characteristics of the interfering signals ................................................... 152
Annex D (normative): Environmental requirements for the BS equipment ................................ 153
D.1 General ................................................................................................................................................. 153
D.2 Normal test environment ...................................................................................................................... 153
D.3 Extreme test environment ..................................................................................................................... 153

D.3.1 Extreme temperature ........................................................................................................................... 153
D.4 Vibration ............................................................................................................................................... 154
D.5 Power supply ........................................................................................................................................ 154
D.6 Measurement of test environments ....................................................................................................... 154
Annex E (normative): General rules for statistical testing ............................................................. 155
Annex F (normative): Global In-Channel TX-Test ........................................................................ 156
F.1 General ................................................................................................................................................. 156

F.2.1 Basic principle ................................................................................................................................................ 156

F.2.2 Output signal of the TX under test ................................................................................................................. 156

F.2.3 Reference signal ............................................................................................................................................. 156

F.2.4 Measurement results ....................................................................................................................................... 156

F.2.5 Measurement points ....................................................................................................................................... 157

F.3.1 Pre FFT minimization process........................................................................................................................ 157

F.3.2 Timing of the FFT window ............................................................................................................................ 158

F.3.3 Resource Element TX power.......................................................................................................................... 158

F.3.4 Post FFT equalisation ..................................................................................................................................... 159

F.4.1 EVM ............................................................................................................................................................... 160

F.4.2 Averaged EVM .............................................................................................................................................. 161

F.4.2.1 Averaged EVM (TDD) ............................................................................................................................. 162
Annex G (informative): Test Tolerances and Derivation of Test Requirements ............................ 163
G.1 Measurement of transmitter .................................................................................................................. 164
G.2 Measurement of receiver ...................................................................................................................... 168
G.3 Measurement of Performance Requirements ....................................................................................... 170
Annex H (Informative): E-UTRAN Measurement Test Cases .......................................................... 171
Annex I (Informative): Measurement system set-up ........................................................................ 172
I.1 Transmitter ........................................................................................................................................... 172
I.1.1 Base station output power, output power dynamics, transmitted signal quality, Frequency error, EVM,

DL RS power, Unwanted emissions ............................................................................................................... 172

I.1.2 Transmitter intermodulation ........................................................................................................................... 172

I.1.3 Time alignment between transmitter branches ............................................................................................... 173

I.1.4 Home BS output power for adjacent channel protection ................................................................................ 173
I.2 Receiver ................................................................................................................................................ 173

I.2.1 Reference sensitivity level .............................................................................................................................. 174

I.2.2 Dynamic range ............................................................................................................................................... 174

I.2.3 In-channel selectivity ..................................................................................................................................... 175

I.2.4 Adjacent Channel Selectivity (ACS) and narrowband blocking .................................................................... 176

I.2.5 Blocking characteristics ................................................................................................................................. 176

I.2.6 Receiver spurious emission ............................................................................................................................ 177

I.2.7 Intermodulation characteristics ...................................................................................................................... 177
ETSI