Transformer Protection and Control RET615 ANSI Application Manual PDF
Preview Transformer Protection and Control RET615 ANSI Application Manual
Relion® 615 Series Transformer Protection and Control RET615 ANSI Application Manual Document ID: 1MAC201230-MB Issued: 3/7/2011 Revision: B Product version: 4.0 © Copyright 2011 ABB. All rights reserved. Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software or hardware described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such license. Trademarks ABB and Relion are registered trademarks of ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders. Warranty Please inquire about the terms of warranty from your nearest ABB representative. ABB Inc. Distribution Automation 4300 Coral Ridge Drive Coral Springs, FL 33065, USA Toll-free: 1 (800) 523-2620 Phone: +1 954-752-6700 Fax: +1 954 345-5329 http://www.abb.com/substationautomation Disclaimer The data, examples and diagrams in this manual are included solely for the concept or product description and are not to be deemed as a statement of guaranteed properties. All persons responsible for applying the equipment addressed in this manual must satisfy themselves that each intended application is suitable and acceptable, including that any applicable safety or other operational requirements are complied with. In particular, any risks in applications where a system failure and/or product failure would create a risk for harm to property or persons (including but not limited to personal injuries or death) shall be the sole responsibility of the person or entity applying the equipment, and those so responsible are hereby requested to ensure that all measures are taken to exclude or mitigate such risks. This document has been carefully checked by ABB but deviations cannot be completely ruled out. In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment. Conformity This product complies with the directive of the Council of the European Communities on the approximation of the laws of the Member States relating to electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and with the product standards EN 60255-6 and EN 60255-27 for the low voltage directive. The IED is designed in accordance with the international standards of the IEC 60255 series and ANSI C37.90. This IED complies with the UL 508 certification. Section 1MAC201230-MB B Section 1 Introduction...........................................................................5 This manual..............................................................................................5 Intended audience....................................................................................5 Product documentation.............................................................................6 Product documentation set..................................................................6 Document revision history...................................................................7 Related documentation........................................................................7 Symbols and conventions.........................................................................7 Safety indication symbols....................................................................7 Manual conventions.............................................................................8 Functions, codes and symbols............................................................9 Section 2 RET615 overview................................................................15 Overview.................................................................................................15 Product version history......................................................................15 PCM600 and IED connectivity package version................................15 Operation functionality............................................................................16 Optional features...............................................................................16 Physical hardware..................................................................................16 Local HMI................................................................................................19 LCD...................................................................................................19 LEDs..................................................................................................20 Keypad..............................................................................................20 Web HMI.................................................................................................21 Authorization...........................................................................................22 Communication.......................................................................................23 Section 3 RET615 configurations .......................................................25 RET615 variant list.................................................................................25 Presentation of standard configurations.................................................25 Standard configurations.....................................................................26 Standard Configuration for Order Code Functional Application AA........30 Applications.......................................................................................30 Functions..........................................................................................31 Default Input/Output (I/O) assignments.............................................34 Typical connection diagrams.............................................................36 Functional diagrams..........................................................................37 Functional diagrams for protection...............................................37 Functional diagrams for control functions ....................................45 Functional diagrams for condition monitoring ..............................47 Functional diagrams for Measurements.......................................49 Functional diagrams for other functions .....................................49 Functional diagrams for logging functions ..................................49 RET615 ANSI 1 Application Manual Section 1MAC201230-MB B Functional diagrams for I/O and Alarm LEDs .............................50 Standard Configuration for Order Code Functional Application BA and CA..............................................................................................53 Applications......................................................................................53 Functions..........................................................................................54 Default Input/Output (I/O) assignments.............................................57 Typical connection diagrams.............................................................59 Functional diagrams..........................................................................61 Functional diagrams for protection...............................................61 Functional diagrams for control functions ....................................72 Functional diagrams for condition monitoring ..............................73 Functional diagrams for Measurements.......................................75 Functional diagrams for other functions .....................................76 Functional diagrams for logging functions ..................................77 Functional diagrams for I/O and Alarm LEDs .............................77 Standard Configuration for Order Code Functional Application BB/CB..82 Applications.......................................................................................82 Functions...........................................................................................83 Default Input/Output (I/O) assignments.............................................86 Typical connection diagrams............................................................88 Functional diagrams..........................................................................89 Functional diagrams for protection...............................................89 Functional diagrams for control functions ..................................100 Functional diagrams for condition monitoring ............................102 Functional diagrams for Measurements.....................................104 Functional diagrams for other functions ...................................105 Functional diagrams for logging functions ................................105 Functional diagrams for I/O and Alarm LEDs ...........................106 Standard Configuration for Order Code Functional Application DA......110 Applications.....................................................................................110 Functions.........................................................................................111 Default Input/Output (I/O) assignments...........................................114 Typical connection diagrams...........................................................116 Functional diagrams........................................................................117 Functional diagrams for protection.............................................117 Functional diagrams for control functions ..................................128 Functional diagrams for condition monitoring ............................129 Functional diagrams for Measurements.....................................132 Functional diagrams for other functions ...................................132 Functional diagrams for logging functions ................................133 Functional diagrams for I/O and Alarm LEDs ...........................134 2 RET615 ANSI Application Manual Section 1MAC201230-MB B Section 4 IED physical connections..................................................139 Inputs....................................................................................................139 Auxiliary supply voltage input..........................................................139 Binary inputs....................................................................................139 Optional light sensor inputs.............................................................141 Outputs.................................................................................................141 Outputs for tripping and controlling..................................................141 Outputs for signalling.......................................................................142 IRF...................................................................................................143 Section 5 Glossary............................................................................145 RET615 ANSI 3 Application Manual Section 1MAC201230-MB B 4 RET615 ANSI Application Manual
Description:The list of books you might like
