performance series 360w rms 4-channel amp kit performance series 180w rms 2-channel amp kit ...

12 Pages·2015·2.4 MB·English

THE DRAG SPECIALTIES
JULY 2015
PERFORMANCE SERIES
360W RMS 4-CHANNEL AMP KIT
• The specific plug-n-play wiring harness included with this kit takes
the two-channels of audio signal available from the Harley RoadGlide
radio (either version), and provides four separate
channels of amplification at 90w RMS continuous,
for each channel
• Full-range class D amplifier is spec’d at 90watts
RMS per channel X4 channels, (360w total) driven
continuously into a 2 ohm load @ 14.4vdc
• Amplifier mounts to the custom made,
stainless-steel 2-piece bracket system, to
provide solid and secure mounting inside the
RoadGlide fairing, in addition to blocking amplifier
heat from being transferred to the radio
• Custom made plug-n-play wiring harnesses
are also included
• Top quality, heavy gauge, power/ground wires
are used for the fused battery connection; all
necessary mounting hardware and complete
installation/operation instructions are included PART # DESCRIPTION SUG. RETAIL
• Amplifier measures 71/4" × 43/4" × 13/4" 4405-0390 For 15 FLTRX/FLTRXS/FLTRUSE models $629.95
PERFORMANCE SERIES 180W RMS
2-CHANNEL AMP KIT
• Full-range class D, amplifier spec’d at 90watts RMS per
channel X2 channels, (180w total) driven continuous into
a 2 ohm load @ 14.4vdc
• Amplifier mounts to the custom made, stainless-steel,
2-piece bracket system, to provide solid and secure mounting
inside the RoadGlide fairing, in addition to blocking amplifier
heat from being transferred to the radio
• Custom made plug-n-play wiring harnesses
are included with this amplifier kit
• Top quality, heavy gauge power/ground
wires are used for the fused battery
connection; all necessary mounting
hardware and complete installation/
operation instructions are included PART # DESCRIPTION SUG. RETAIL
• Amplifier measures 61/2" × 43/4" × 13/4" 4405-0389 For 15 FLTRX/FLTRXS/FLTRUSE models $439.95
ROKKER® XX 6.65" FAIRING SPEAKER KIT
• Lightweight, waterproof, one-piece woven-fiber driver cone
• High-output, silk-dome tweeter
• Super high-density, light-weight neodymium magnet structure,
specially coated to maintain flux-strength integrity even at
extreme operating temperatures
• High-efficiency, vented voice-coil and magnet structure for improved
cooling when operating at high volume levels for extended periods
• Custom max-flow speaker grills for crystal-clear sound
at highway speeds
• Mounting hole pattern and spade electrical connections
are exactly the same as the factory specification
• Plug-and-play, no-modification solution complete PART # DESCRIPTION SUG. RETAIL
with easy to follow installation instructions 4405-0388 For 15 FLTRX/FLTRXS/FLTRUSE models $389.95
dragspecialties.com
THE DRAG SPECIALTIES
JULY 2015
PHANTOM II
EXHAUST SYSTEM
• Brand new Paul Yaffe-
inspired design
• Curvy 2:1 custom stylized
pipe features 2" primary
header pipes flowing into
a 3.5" collector
• Black ceramic-coated with
four-piece chrome heatshields
• Rebuildable/removable baffle gives
a great throaty roar
• Passenger-friendly design PART # DESCRIPTION SUG. RETAIL
• Made in the U.S.A. 1800-1815 For 14-15 XL models $1,499.95
2.5" MAVERICK
1801-0801
SLIP-ON MUFFLERS
• Feature 2.5" diameter chrome or
matte black round muffler bodies
• Maintenance-free, high-flowing,
louvered baffles will never
need repacking
• All mufflers feature precision
CNC-machined billet aluminum
end caps with high-temperature
black ceramic coating
• Brushed stainless steel muffler
badges featuring an embossed
Crusher work mark logo
• Sold in pairs
1801-0803
• Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL PART # DESCRIPTION SUG. RETAIL
CHROME MATTE BLACK
1801-0801 For 07-10 FXST/B/C, 07-15 FLSTC, 08-11 FXCW/C $399.99 1801-0803 For 07-15 FLSTF, FXSTD $449.99
1801-0802 For 07-15 FLSTF, FXSTD 399.99 For 07-15 FLSTN, 08-11 FLSTSB
1801-0805 449.99
For 07-15 FLSTN, 08-11 FLSTSB (except 14-15 FLSTNSE)
1801-0804 399.99
(except 14-15 FLSTNSE) For 91-15 FXD/FXDWG (except 08-15 FXDF,
1801-0807 449.99
For 91-15 FXD/FXDWG (except 08-15 FXDF, 10-15 FXDWG, 12-15 FLD, 15 FXDL)
1801-0806 399.99
10-15 FXDWG, 12-15 FLD, 15 FXDL) 1801-0809 For 08-15 FXDF, 10-14 FXDWG 449.99
1801-0808 For 08-15 FXDF, 10-14 FXDWG 399.99 1801-0811 For 04-13 XL 449.99
1801-0810 For 04-13 XL 399.99 1801-0813 For 14-15 XL 449.95
1801-0812 For 14-15 XL 399.95
DISCLAIMER: THE CALIFORNIA AIR RESOURCES BOARD (“CARB”) DOES NOT PERMIT THE USE OF AFTERMARKET EMISSION-RELATED PART(S) THAT ALTER THE PERFORMANCE OF OEM EMISSION-RELATED DEVICES
UNLESS CARB HAS ISSUED AN EXECUTIVE ORDER, OTHER THAN ON RACING VEHICLES ON CLOSED COURSES. CHECK YOUR LOCAL LAWS AND MANUFACTURER’S INFORMATION.
2
1800-1756
1800-1755
1800-1758
1800-1757
1800-1759 1800-1760
FUSION EXHAUST SYSTEMS
• Not tame or mild, these pipes will definitely draw
attention to your ride
• Sound is not obnoxious, but a deep, strong rumble
• Mufflers feature hexagon-shape exhaust tips with robotic welds
• Not designed for use with the OEM air cleaner; aftermarket air cleaner and
• Heat shields are stamped steel with edgy designs performance fuel management module are highly recommended
• Exhaust tips are curved to direct heat away from the saddlebags • Include O ports and necessary plugs, bungs, etc., for all year applications
2
• Will work with saddlebag extensions and passenger footpegs • Made in the U.S.A.
FOR 95-15 FLHT/FLHR/FLTR/FLHX AND H-D FL TRIKE (EXCEPT 15 FLRT)
PART # DESCRIPTION SUG. RETAIL PART # DESCRIPTION SUG. RETAIL
1800-1755 Chrome pipes/chrome heat shields/chrome tips $799.95 1800-1758 Black pipes/black heat shields/black tips $799.95
1800-1756 Chrome pipes/black heat shields/chrome tips 799.95 1800-1759 Black pipes/chrome heat shields/black tips 799.95
1800-1757 Chrome pipes/black heat shields/black tips 799.95 1800-1760 Black pipes/chrome heat shields/chrome tips 799.95
POWER PORT DUAL BUNG HEADPIPES
• Dual headpipes taken to a whole new level
• PowerPort crossover provides power
boost across entire rpm range
• 2.5" heat shields
• Quick, simple installation 1802-0293
• Accepts OEM mufflers or any 95-15 OEM style mufflers
• Feature 12mm and 18mm bungs and include installed 18mm
bung plugs with copper sealing washers
PART # DESCRIPTION SUG. RETAIL
• 2009 models will require 12mm bung plugs (sold separately)
FOR 09-15 FLHT/FLHR/FLHX/FLTR MODELS (EXCEPT 10 FLHTCUSE)
• Made in the U.S.A. 1802-0293 W/ chrome heatshields $559.95
NOTE: Mufflers not included; must be purchased separately. 1802-0294 W/ black heatshields 639.95
DISCLAIMER: THE CALIFORNIA AIR RESOURCES BOARD (“CARB”) DOES NOT PERMIT THE USE OF AFTERMARKET EMISSION-RELATED PART(S) THAT ALTER THE PERFORMANCE OF OEM EMISSION-RELATED DEVICES
UNLESS CARB HAS ISSUED AN EXECUTIVE ORDER, OTHER THAN ON RACING VEHICLES ON CLOSED COURSES. CHECK YOUR LOCAL LAWS AND MANUFACTURER’S INFORMATION.
3
THE DRAG SPECIALTIES
JULY 2015
KLOCK WERKS
If you have not tried-
on and tried-out a pair of Klock Werks’ Klip Hanger
Handlebars, like the new ones you see below, then you
don’t know what both you and your customers are missing.
The bar sections themselves are available in several heights
depending upon bike model. The “Klamps” that mount
the control/grip portions can then be adjusted in several
directions to perfectly suit any rider’s exact liking. Have
a pair or two mounted for your customers to try on for size.
KLIP-HANGER PULLBACK HANDLEBARS
• Innovative bars present the ultimate in rider • All are drilled/slotted for
personal adjustment and fit wiring, and bar end is
notched for throttle by
• Offer more pullback than the standard Klip Hanger
wire applications
bars for a more relaxed ride
• All include chromed, billet
• Unique “Klamps” allow control/grip portions of the
aluminum, domed bar end
handlebar to be adjusted in several directions; rider
plugs for a finished look
can tailor to his/her exact liking
• Work with HD OEM Heated Grips
• Bar sections are manufactured from DOM tubing,
‘Klamps’ are machined from 6061 billet aluminum • Fit perfectly with the new narrower center
and all hardware is stainless steel section of the Road Glide 15+ models with
anti-vibration clamps
• All feature a fully knurled 1.25" riser clamp area
0601-3124
for standard risers • Made in the U.S.A.
FOR 15 FLTRX/FLTRXS/FLTRUSE AND CUSTOM APPLICATIONS
PART # SUG. RETAIL DESCRIPTION UPRIGHT BAR RISE GRIP-TO-GRIP WIDTH
10"
0601-3126 $459.95 Chrome/chrome 10" 35"
0601-3125 459.95 Black/chrome 10" 35"
0601-3124 459.95 Black/black 10" 35"
14"
0601-3129 459.95 Chrome/chrome 14" 35"
0601-3128 459.95 Black/chrome 14" 35"
0601-3127 459.95 Black/black 14" 35"
2212-0567 2212-0569 2212-0571
MVX-8K SERIES ANALOG/DIGITAL PLUG-IN INSTRUMENTATION
• Six-gauge kits provide all seven gauge readings displayed in the speedometer and tachometer
LCD readouts (speed, rpm, volts, fuel, oil pressure, oil temp, and air temp), as well as miles
to empty, and performance readouts (0-60 time, and quarter-mile speed and time)
• Personalize your gauge set by programming the pointer, backlight and LCD
message center colors independently SIX-GAUGE KITS
PART # DESCRIPTION SUG. RETAIL
• Kits include speedometer, tachometer, oil pressure, oil temperature,
FOR 96-03 FLHT/FLTR
fuel level and voltmeter
2212-0566 Black/gray background w/ chrome bezel $1,499.95
• Seven user-selectable LED lighting colors available for background, message
2212-0567 Black/gray background w/ black bezel 1,499.95
and pointer: red, green, blue, teal, magenta, amber or white
2212-0568 White/gray background w/ chrome bezel 1,499.95
• Three background options to choose from: black/gray, white/gray or black/red
2212-0569 White/gray background w/ black bezel 1,499.95
• Chrome or black bezels available 2212-0570 Black/red background w/ chrome bezel 1,499.95
• Proudly designed and manufactured in the U.S.A. 2212-0571 Black/red background w/ black bezel 1,499.95
4
GASBOX
Earlier we told
you a little bit about the Gasbox 2010-1248
folks who are cranking out hot
new custom products from a large,
2010-1247
nondescript warehouse in an
industrial area of Cleveland, Ohio.
MOUNT BRACKETS FOR JOHNNY FIVE TAILLIGHT
We also told you that they were
starting to gain a lot of attention • Allow installation of the Johnny Five taillight (PART #2010-1231) to a license
plate bracket without provision for a light
within the custom bike world and
• Mount brackets are drilled to match
that we would certainly be doing a standard 4" × 7" license plate
our part to make certain every new • Made in the U.S.A.
Gasbox accessory was in stock and PART # DESCRIPTION SUG. RETAIL
ready to go. Just like the ones you 2010-1247 Vertical taillight mount bracket $12.95
see right here. 2010-1248 Horizontal taillight mount bracket 12.95
0933-0114
SWITCH ACCENT TRIM
• Polished stainless steel construction
will not rust, pit, chip or discolor
• Dresses up the inner fairing cap assembly
• No mounting hardware required
0933-0113
• Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL
2202-0208 For 14-15 FLHTCU, FLHTK models $78.95
CUSTOM TOP
MOTOR MOUNTS
• These heavy-duty, custom top motor
mounts from Gasbox feature a convenient
spot to relocate your ignition switch and
a coil mount
• Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL
For 04-15 XL models (designed for OEM
0933-0114 $74.95
fuel-injected coil)
For 86-03 XL models (will not work with
0933-0113 74.95
stock petcock on left side of tank)
FRISCO STYLE 0411-0121
GAS TANK LIFT KIT ELITE SERIES
BLACK RAPTURE
• Kit raises the front of the tank
several inches, providing the Frisco look but FORK SLIDER COVERS
without the cost of a new tank or paint job
• 6061 billet aluminum construction
• Bracket will lift the front of the tank approx.
3.5" center-to-center on the mounting holes • Easily create a custom look by replacing the factory stock fork slider covers
• Made from heavy-gauge steel with a machined • Covers complete the Elite line of products including
spacer; welded and powder-coated for durability foot controls, windshield trim and bag latches
• Install by removing your tank’s front mount • Sold in pairs
hardware, sliding the bracket in and using your • Made in the U.S.A.
stock hardware and the additional hardware
included, then bolting the tank back on PART # DESCRIPTION SUG. RETAIL
• Made in the U.S.A. 0411-0121 For 14-15 FLHT, FLHR, FLTRX, $489.95
FLHX and H-D FL Trike
PART # DESCRIPTION SUG. RETAIL For 84-13 FLT, FLHT, FLHR,
0411-0120 489.95
0704-0018 For 86-03 Sportster models $49.95 FLTR, FLHX and H-D FL Trike
5
THE DRAG SPECIALTIES
JULY 2015
0802-0853
0802-0852
PROFILER BW SEATS
• Slammed two-up seat features narrow styling, a thin profile and low riding height
• Seat design drops the rider down into the bike for the lowest riding position
PROFILER TTR SEATS
possible, while maintaining our high standard of comfort and support
• Slammed two-up seat features narrow styling, a thin profile and low riding height • Unique blend of variable-density foam
and SaddleGel™ eases tailbone pressure
• Seat is designed to drop the rider down into the bike for the lowest riding position
and improves circulation
possible while still maintaining a high level of comfort and seat support
• Contrasting grain, basket weave SaddleHyde™ cover
• Unique blend of variable-density seat
foam and SaddleGel™ eases tailbone • Basket weave pattern on driver’s seat provides more breathability and extra grip
pressure and improves circulation if needed
• Authentic True Tuck-and-Roll construction, not a quick cross-stitch; seat is • Basket weave is sewn into the slender tail section to accent the low seat styling
covered in genuine leather for a bold look and profile
• Made in the U.S.A. • Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL PART # DESCRIPTION SUG. RETAIL
0802-0854 For 06-10 FXST, 07-15 FLSTF/B $325.00 0802-0853 For 06-10 FXST, 07-15 FLSTF/B $310.00
0802-0852 For 00-05 FXST, FLST (except FXSTD, FLSTN) 325.00 0802-0851 For 00-05 FXST/FLST (except FXSTD, FLSTN) 310.00
0802-08561 For 06-15 FLSTC, FLSTN 325.00 0802-08551 For 06-15 FLSTC, FLSTN 310.00
0802-0858 For 07-10 FXSTC 325.00 0802-0857 For 07-10 FXSTC 310.00
1 FLSTN models require removal of seat rail and rear rack. 1 FLSTN models require removal of seat rail and rear rack.
1510-0250
1510-0251
BOLERO SEAT
7" SOLO LUGGAGE RACKS
• Narrow, thin and clean while still retaining comfort and a touch of style
• Looks great on any 96-03 model Sporty, representing a perfect blend • Bigger and beefier luggage rack that still maintains style
of old and new
• Matches perfectly with larger fenders
• Features controlled density polyurethane foam
• Outside rails made of heavy .065 tubing; inside rails are 3⁄8" solid steel
• Baseplate is marine grade fiberglass
• Measure approx. 11" long × 7" wide
• RSD metal logo
• Made in the U.S.A.
• Direct bolt-on
PART # DESCRIPTION SUG. RETAIL
• Made in the U.S.A.
FOR 13-15 FXSB
PART # DESCRIPTION SUG. RETAIL 1510-0250 Black $132.95
0804-0580 For 96-03 XL models $329.95 1510-0251 Chrome $132.95
6
CARL BROUHARD CROSS DESIGN PREDATOR SEAT
• Solar-reflective leather in the seating area and automotive-grade vinyl on the
sides; patented process reduces surface temperature by as much as 25°F for
a cooler seat, higher durability and longer life over conventional leather or vinyl
• Features Carl Brouhard cross stitch design
• Molded polyurethane foam interior for maximum comfort
• 3⁄16" ABS thermoformed seat base for a perfect fit
• Low-profile Predator design with a lower seating
position compared to stock
• Rubber bumpers and fully carpeted bottom to protect paint
• Includes all mounting hardware PART # DESCRIPTION SUG. RETAIL
• Made in the U.S.A. by Drag Specialties® Seats 0801-0955 For 08-15 FLHT, FLHR, FLTR, FLHX models (301/2" overall × 11" W front × 6" W rear) $339.95
MinimalIST SOLO
• Styled narrow and sleek with minimal back support
• Excellent for the weekend rider who prefers
a classic old-school look
• Designed with IST seating technology engineered to reduce the vibration,
compression and shock the body feels from riding, to enable longer, more
comfortable rides
• Features a highly durable, soft, textured, black vinyl cover with matching
black vinyl side panels that will keep their shape across the high-stress points
of the seat
• Made in the U.S.A.
PA RT # DESCRIPTION SUG. RETAIL
FOR 06-10 FXST, 07-15 FLSTF/B
0802-0829 Black vinyl $229.95
RAKED ROAD
KING NACELLE
• Designed for use on
raked Road Kings, so owners are not
left with a headlight pointing to the sky
• Nacelle corrects the headlight position
and adds killer styling
• High-pressure, composite Nacelle perfectly
fits Bagger Nation 7° or 9° raked trees and
will accept the stock riser cover, cowling
spear and headlight assembly
• Comes primed and ready for paint
PART # DESCRIPTION SUG. RETAIL
2001-0953 For Bagger Nation Road King raked trees w/ 23" or 26" wheel $449.95
7
THE DRAG SPECIALTIES
JULY 2015
J.W. SPEAKER CORPORATION
We’re proud
to welcome another addition to our Drag Specialties family - the J.W. Speaker
Corporation. Founded in 1935 by John W. Speaker, their focus is on developing
innovative, high-performance vehicle lighting for both OEM and aftermarket
customers around the world. One of their specialties is LED lighting that includes
our new additions you see here. And all of their products are proudly designed,
manufactured and assembled
in Germantown WI, U.S.A.
7" EVOLUTION 2 LED HEADLIGHTS
• Direct replacement for most 7" headlights
• Superior visibility, safety and durability
4.5" LED 2001-1107
• 1150 lumen output (high beam),
FOG LIGHTS
750 lumen output (low beam)
• DOT compliant • Replacement for stock
PAR36 fog lights
• Easy, plug-n-play H4-style connector
2001-1105 • Outperform bulb-based fog
• Mount kit required for Dresser lights with superior visibility,
applications (sold separately) extreme durability and unmatched longevity
• Made in the U.S.A. • Compatible with most fog light housings
NOTE: 14-15 Dressers will require 2001-1104 • Sold each
wire harness adapters, PART #
2120-0647 or 2120-0655. • SAE/ECE compliant 2001-1108
• Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL
2001-1104 Black $390.95 PART # DESCRIPTION SUG. RETAIL
2001-1105 Chrome 390.95 2001-1107 Black $240.95
2001-1106 Mount kit 79.95 2001-1108 Chrome 240.95
2001-1106
2040-1701
MAGICFLEX2® 72 LED
2020-1096
FLEXIBLE STRIPS
2020-1095 • 39.4" long
• High-output,
surface-mount
5050 LEDs
2020-1097
• Three high-output 5050 LEDs per inch
COMPLETE LED TURN SIGNAL CONVERSION KITS • 120° degree viewing angle
• Conformal-coated for 100% waterproof
• Kits include Dynamic Ringz™ amber front LED turn signals, red rear LED turn signals,
four smoked lenses and plug & play SMART Signal Stabilizer, where applicable • Great for trike wheel wells
• Available in multiple colors
PART # DESCRIPTION SUG. RETAIL
• Sold each
For 11-15 Softail, 12-15 Dyna, 14-15 XL, 12-15 FLHX, FLTR and 14-15 FLSTNSE, SUG.
2020-1097 $194.95
FXSBSE w/ bullet style turn signals; 1157 front and 1157 rear (no stabilizer) PART # DESCRIPTION RETAIL
2020-1098 For 11-15 Softail, 12-15 Dyna, 14-15 XL and 14-15 FLHTKSE, FLHTRUSE 194.95 2040-1701 Red $64.95
w/ bullet style turn signals; 1157 front and 1156 rear (no stabilizer)
2040-1702 Blue 64.95
For 96-10 Softail, 02-11 Dyna, 97-13 FLHT, FLHR, FLTR, FLTRU (does not fit FLTRX),
2020-1094 269.95 2040-1703 Green 64.95
06-09 FLHX and 02-03 XL models w/ bullet style turn signals; 1157 front and 1156 rear
2040-1704 Orange 64.95
For 96-10 Softail and 97-13 FLHT, FLHR, FLTR models w/ flat style turn signals;
2020-1095 1157 front and 1156 rear 269.95 2040-1705 Purple 64.95
For 10-13 FLHX/FLTRX Custom models w/ bullet style turn signals; 2040-1706 White 64.95
2020-1096 269.95
1157 front and 1157 rear 2040-1707 Pink 64.95
2020-1099 For 04-13 Sportster models w/ bullet style turn signals; 1157 front and 1156 rear 269.95 2040-1708 Amber 64.95
8
HEADWINDS
Owners Joel
and Julie Felty, along with all of the expert
craftsmen at Headwinds, have proudly
provided the highest quality lighting available
anywhere to custom motorcycle and hot-rod
builders since 1992. Their headlights feature
smooth, non-wavy surfaces with mirror-like
finishes along with innovations that do away
with exposed rivets, bolts, and flanges. All of
these features add up to the perfect choice for
your custom builders or riders who want the
finest in modern classically-styled lighting.
H4 LED HEADLIGHT BULB
• Brighter and whiter than halogen bulbs
• Dual-beam LED, 25W low/50W high
• 12-14V, 3,000 lumens, 6,000° Kelvin color temperature
• Kit includes bulb, driver, three-prong connector and cooling ribbon heat sink
• Cooling ribbon improves LED performance and longevity
• Fits H4 and HB2 lamps with P43T flange base
• Recommended for 53/4" diameter headlamp assemblies
NOTE: Not DOT certified.
PART # DESCRIPTION SUG. RETAIL
2060-0474 For 03-15 FXST, FXD/FXDWG, 98-13 FLTR $99.95
ILLUMINATOR PLUG-IN STYLE RUN, PLUG-IN AUTOMATIC TURN SIGNAL CANCELER
BRAKE AND TURN SIGNAL MODULE
• Plugs in and replaces the OEM signal canceler
• Compatible with TSM/TSSM modules and security systems • Does not require stock speedometer for proper operation
• Turns stock or custom turn signals into running lights and brake lights; still • Automatically flashes for 11 seconds; can be manually canceled at any time
maintains turn signal function
• Built-in emergency flasher mode
• Increases visibility of the motorcycle from the rear
• Built-in load equalizer runs LEDs of up to 50W per side
• Built-in load equalizer works with stock signals and can run the smallest custom
signals, even LEDs • Measures 27⁄8" L × 13⁄8" W × 7⁄8" D
• Comes with easy-to-follow instructions and features plug-in connectors for • Made in the U.S.A.
hassle-free installation on select models NOTE: Be sure to identify which connector is on the bike before purchasing,
• Works with incandescent, halogen and 12V LED signals and markers as the factory was not consistent during 1994-2000.
• Made in the U.S.A.
PART # DESCRIPTION SUG. RETAIL
PART # DESCRIPTION SUG. RETAIL Female Deutsch style 8-pin plug for
2050-0215 $94.95
2050-0214 For 91-93 FLHT models $118.95 94-00 models w/o Delphi TSM
9
THE DRAG SPECIALTIES
JULY 2015
2010-1239
0703-0688
LED TAILLIGHT
• Light assembly fits neatly under
the rear edge of the OEM rear fender
• Dual-function design 2010-1240
• Available with red or smoked lens
• Simple three-wire hookup (requires hardwiring)
PART # DESCRIPTION SUG. RETAIL
FOR 13-15 FXSB
2010-1239 W/ red lens $129.95 0703-0691
2010-1240 W/ smoke lens 129.95
SCREW-IN LOCKING SKULL GAS CAPS
• Key slot is hidden under the skull to keep dirt and debris out of the lock
• Available in chrome with chrome skull or gloss black with chrome skull
• Come with two keys
• Caps sold each
CHROME FORK LOCK PART # DESCRIPTION SUG. RETAIL
FOR 84-E96 MODELS, 82-83 FXR, 83-84 FX/FXWG/FLH, 83-85 XL
• Includes two keys
0703-0688 Chrome, vented $38.95
0703-0689 Chrome, non-vented 38.95
PART # DESCRIPTION SUG. RETAIL 0703-0690 Gloss black, vented 38.95
0420-0003 For 01-05 FXD, 01-15 FXST/FLST $24.95 0703-0691 Gloss black, non-vented 38.95
1731-0420
1731-0417
HANDLEBAR CLAMP
1731-0418 SCREWS WITH SPACERS
MASTER CYLINDER REBUILD KITS • For 84-15 models with 31/2" on-center
risers and offset mounting holes
• Meet or exceed OEM specifications 1731-0419 • Spacers allow installation of clamp-mounted
PART # DESCRIPTION SUG. RETAIL gauges on most clamps with recessed screws
FRONT • Chrome finish
1731-0417 For 14-15 XL, 15 Softails, single disc models, 7⁄16" bore (non-ABS); $29.95 • Sold in pairs
repl. OEM #41700087
PART # DESCRIPTION SUG. RETAIL
1731-0418 For 14-15 XL dual disc models, 1/2" bore (non ABS); repl. OEM #41700088 29.95
1731-0420 For 14-15 XL single disc models (ABS); repl. OEM #41700084 29.95 5⁄16"-18 handlebar
screws w/ spacers;
REAR 0603-0555 repl. OEM #s $6.95
1731-0419 For 14-15 XL; repl. OEM #41700097 29.95 4326A, 5736
10