Table Of Content

इंटरनेट मानक Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public. “जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न’ 5 तरफ” Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru “The Right to Information, The Right to Live” “Step Out From the Old to the New” IS 5054-2 (2007): Radio frequency connectors, Part 2: Coaxial unmatched connector [LITD 3: Electromechanical COmponents and Mechnical Structures for Electronic Equipment] “!ान $ एक न’ भारत का +नम-ण” Satyanarayan Gangaram Pitroda ““IInnvveenntt aa NNeeww IInnddiiaa UUssiinngg KKnnoowwlleeddggee”” “!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता हहहहै””ै” Bhartṛhari—Nītiśatakam “Knowledge is such a treasure which cannot be stolen” IS 5054 (Part 2) :2007 IEC 60169-2:1965 W?a7mw m 3ngRr+ihl@- w-J-12 wwefkwJtii%imilGm Indian Standard RADIO FREQUENCY CONNECTORS PART 2 COAXIAL UNMATCHED CONNECTOR lCS 33.120.30 (3Bl>,zu07 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI 110002 October 2007 Price Group 4 Electromechanical Components and Mechanical Structures for Electronic Equipment, LITD 03 NATIONAL FOREWORD This Indian Standard (Part 2)which is identical with IEC 60169-2: 1965 ‘Radio-frequency connectors — Part 2: Coaxial unmatched comector’ along with Amendment No. I (1982) issued by the International Electrotechnical Commission (IEC) was adopted by the Bureau of Indian Standards on the recommendation of the Electromechanical Components and Mechanical Structures for Electronic Equipment Sectional Committee and approval of the Electronics and Information Technology Division Council. The text of IEC Standard has been approved as suitable for publication as an Indian Standard without deviations. Certain conventions are, however, not identical to those used in Indian Standards. Attention is particularly drawn to the following: a) Wherever the words ‘International Standard’ appear referring to this standard, they should be read as ‘Indian Standard’. b) Comma (,) has been used as a decimal marker, while in Indian Standards, the current practice is to use apoint (.) as the decimal marker. Amendment No. 1to the above International Standard has been given at the end of this publication. [nthis adopted standard, reference appears to the following International Standard for which Indian Standard also exists. The corresponding Indian Standard, which is to be substituted in its place, is listed below along with itsdegree of equivalence for the edition indicated: International Standard Corresponding Indian Standard Degree of Equivalence IEC 60169-1 : 1987 Radio-ffequency IS 5054 (Part l/See 1) : 1995 Radio Identical connectors — Part 1: General requirements frequency connectors: Part 1 General and measuring methods requirements and measuring methods, Section 1General (second revision) Only the English text of the International Standard has been retained while adopting it as an Indian Standard, and assuch the page numbers given here are not the same as inthe IEC Publication. IS 5054 (Part 2) :2007 IEC 60169-2:1965 IndianStandard RADIO FREQUENCY CONNECTORS PART 2 COAXIAL UNMATCHED CONNECTOR 1. Dimensions 1.1 Connector ,Optionat insulation FIGURE 1 FiGuRE 2 The miliimetre dimensions are derived from the original inch dimensions. 1 la b c d e f h [ I 1 mm 1.3 2.36 8.05 9.525 I 0.8 7.11 7.54 min min min min ~0.076 *0.05 I *0.4 in 0.051 0.093 0.317 0.375 1/32 0.280 23/64 19/64 min min I min min min +0.003 *0.002 ~*1/64 I 1 IS 5054 (Part 2) :2007 IEC 60169-2:1965 1.2 Gauger m fld r 1 I y ~~a 0 / FIGURE 3 FIGURE 4 FIGURE 5 FIGURE 6 Noie.- ~dcnoks amaximumsurfamrough- ofR. = 0.5wm(20Lin). Themillimetredimensionsarederivedfrom theoriginalinchdimensions. a b d _-.._— Ic 2.438 2.286 9.575 9.474 mm + 0.01 0 +0.01 – $01 0 – 0.01 0 0.0960 oa900 – 0.3770 0.3730 in o +0.0004 0 +0.0004 –0.0004 0 – 0.0004 0 I I Gaugefor Flgurc Material — ./ Sizingpurposes 3and5 WeCl(hardened) Measurement ofcontact resistance 4and6 Underconsideration Measurementofgaugeretention 4and6 Steel(hardened) force Weight: SW@Fis. 4: Under consideration gaugeF@ 6: Underconsideration IS 5054 (Part 2): 2007 IEC 60169-2:1965 1.3 Mating componentfor socket conneclorsfor endurance test Material: steel (hardened). ea -0 FIGURE 7 The millimetre dimensions are derived from the original inch dimensions. a b c d e f . 9.576 8.05 2.438 9.1 7.112 0.8 tin min min mm o 0 - 0 .01 – 0.01 * 0.4 0.377 0.317 0.096 23/64 0.280 min min min 1/32 in o 0 – 0.0004 -0.0004 + 1/64 i IS 5054( Part2) :2007 IEC 60169-2:1965 2. Climatic group: 666 Rated temperature range: — 25°C to + 70°C Damp heat, long term: 4 days. 3. Schedule for type test This schedule shows all tests and the order in which they have to be carried out as well as the requirements to be met. 3.1 Allspecimensshall be subjectedto the followingtests: CIauseof Teat lECPubIication Conditions oftest Requirements 169-1 Vkiualins~tion 12 Dimensions 13 Contact resistance 14.3 For inner contact: gauges Figs. 3 and4 Rz=lOmflmax For outer contact: gauges Figs. 4 and 6 R,= 5mf2rnax Matedacts: Inner contact RI = 10mQ rnax Outer contact RI = 5mQmax Insulation resistance 14.5 10sM Qrnin Capacitance 14.9 5pF max 1 3.2 The connectors shall then be divided into three lots. All connectors in each lot shall undergo the following tests: II Clause of Test IECPublication Conditions oftest Requirements 169-1 l— Firs! lot Effectivenessofclamp- ‘ 15.4.3 Cableto beused: 96-IEC-50-3-13 ing device against Innerconductorofcableconnected: cablepulling lengthofcable: 50cm F=50N(5kgf) f = 1minute Effect ofcable rotation ~ 15.4.2 Cable tobeused: 96-IEC-7541 3 Minimum bending radius: 5cm Number of revolutions: 25 Effectiveness of clamp- J5.4.4 Cable to be used: 96-lEC-75-4-13 ing device against \ Length of cable: 50cm cable Ixnding F = 50 N (5kgf) Number of bends: 25 4 IS 5054( Part2) :2007 IEC 60169-2:1965 Clauseof Test ~CPublication Conditions oftests Requirements 169-1 ;tandard test sequence: 15.2 Soldering 15.2.1 Solderingiron method: sizeB Gaugeretention force 15.2.3 InnerConductor:gaugesFigs.3and4 (resilientsocket Outerconductor: gaugesF@ Sand6 contacts) finalmeasurements: Insulation resistance 14.5 lMflmin Reflectioncoefficient 14.1 Contactrmistancc 14.3 For inner contact RI=10 mn rnax For outer contact RI= 5m fl ma% Visuatinspection 12 Insertion force: :ngcrtionandwithdrawal 15.3 Under consideration force of mated con- Withdrawal force: nectors Under consideration :Iimatic sequence: 16.2 Dryheat 16.2.1 Insulation resistanm (hot): lMf2min Damp heat,awclerate 16.2.2 Onecycle Cold 16.2.3 Final measurements: Insulation resistance 14.5 lMf2min Contact resistance 14.3 For inner contact RI= 10mf2nMX For outer contact RI= 5mfl mas Visualinspcztion 12 Second lot Dampheat, longterm 16.3 Finalmeasurements: Insulation resistance 14.5 lML2rnin Contact resistance 14.3 Forinnercontact RI= 10mf2max For outercontact RI = 5mf)max Visualinspection 12 I 5