ebook img

Water Supply PDF

709 Pages·15.129 MB·English
Save to my drive
Quick download
Download
Most books are stored in the elastic cloud where traffic is expensive. For this reason, we have a limit on daily download.

Preview Water Supply

Preface A number of key specialists in the water industry have contributed to the production of this fifth edition of Water Supply and as a result most chapters have been re-written, extended and updated. The text gives up-to-date national and international standards for drinking water quality set by the UK and EC regulatory bodies plus the World Health Organization and the US Environmental Protection Agency. It describes the incidence and significance of the main chemical constituents found in raw waters, and the types of bacteria, viruses and protozoan organisms which present a hazard to human health. New matters of concern with respect to chemical and microbiological contaminants are listed. The design si given of treatment works and the equipment used for chemical coagulation, clarification methods including dissolved air flotation, rapid gravity filtration, slow sand filtration and membrane filtration. Sludge disposal methods are presented with design parameters and tables of relevant data. The new 1999 UK regulations with respect to monitoring for cryptosporidium oocysts are given, and treatment practices recommended to reduce the risk of oocysts passing into supply are described. Advanced and specialised treatments are described for iron, arsenic and manganese removal, plumbosolvency control, defluoridation and fluoridation, nitrate and ammonia removal. Taste and odour causes and removal; and reduction of volatile organic compounds and micropollutants by use of granular activated carbon (GAC) and advanced oxidation processes are dealt with. Further material si added on desalination by ion exchange, electrodialysis, reverse osmosis and thermal processes. The new approach to the management of distribution systems si described. Zoning of supplies, telemetered monitoring of district flows, computer modelling of flows and water quality modelling, together with geographic information systems are increasingly being used to provide data on system performance, levels of service to consumers and the condition of assets for the development of asset management plans. Methods of rehabilitating pipelines are discussed. An extended chapter on pipes and pipelines gives additional information on the design of steel, polyethylene and PVC pipes according to numerous international and in-country standards. Material on the yield of sources has been remodelled to emphasize the important role played by underground water supplies throughout the world. New approaches to definitions of 'yield' are discussed; and reference si directed to the new Flood Estimation Handbook 1999 for estimating flood magnitudes. Experience with privatization of the water industry in England and Wales si reported together with a consideration of the growth of private sector participation in public water supply overseas. Levels of staffing of waterworks undertakings in UK and other countries x Preface are given. New information si presented on the water demand experienced by USA water undertakings and the revised approach of the US Environmental Protection Agency to drinking water quality control. The authors are grateful to the many contributors and reviewers who have aided the production of this fifth edition and to the firm of Binnie, Black & Veatch who have made this co-operative venture possible. The text also benefits from the contributions of F. M. Law, F. W. Crowley and Dr R. C. Hoather to previous editions. However we must make clear that responsibility for the statements and opinions expressed lies with ourselves. Alan C. Twort Don D. Ratnayaka Malcolm J. Brandt Contributing Authors dv sor Reviewers s a dn Contributing authors from Binnie, Black 8 Veatch Peter B. Clark Technical Director (Hydraulics) ,AB MA, MSc, MICE Tony N. Coe Chief Mechanical Engineer (Pumping Plant) MA, FIMechE, FCIWEM Neville A. Cowton Technical Director (Service Reservoirs) BSc, MSc, MICE, MCIWEM Ken J. Edworthy Consultant Hydrogeologist (Groundwater Supplies) BSc, FGS, MCIWEM Mike J. Little Technical Director (Pipelines) MA, MICE, MCIWEM David E. MacDonald Chief Hydrologist (Surface Supplies & Floods) BSc, MSc, MCIWEM John C. Maunder Consultant, Control & Instrumentation BSc, MIEE (Control & Automation Systems) Alvin J. Smith Chief Biologist (Water Biology & Storage) BSc, MIBiol, MIWEM Peter J. Speight Chief Electrical Engineer (Electrical Systems & Motors) ,cSB MIEE Contributing author from Drinking Water Inspectorate Claire R. Jackson Principal Inspector, Drinking Water Inspectorate; formerly MRSC, FCIWEM Senior Chemist, Binnie & Partners (Water Quality Issues and Standards) xii Contributb~g Authors, Reviewers and Advisors Technical reviewers and advisors Binnie, Black 8 Veatch John Ackers Terry Heard BSc, MICE, MCIWEM BSc, MRSC, MCIWEM Roger Brown Peter Mason BSc, MSc, DIC, FICE, FCIWEM BSc, MPhil, PhD, FICE Ken Harper Chris Scott ,AB MICE, MCIWEM BSc, MSc, MICE Others David Drury MIBiol, MEWICM Drinking Water Inspectorate Bob Hulsey ,sa SM Black & Veatch Owen Hydes OBE, BSc, MRSC Drinking Water Inspectorate Frank Law ,csa MICE, MEWICF Institute of Hydrology Jon McLean ,cSa MBA, MICM Hanovia Limited Pierre Mouchet ,MP &.rgA.gnE Forestry Degremont Trevor Peploe a.Tech, MRSC, MIWEM Paterson Candy Limited Mark Smith ,csa CSRM Drinking Water Inspectorate Neil Wade ,AM EhceMIF Mott, Ewbank Preece Abbreviations used ni bibliographies ASCE American Society of Civil Engineers, Reston, VA, USA ASME American Society of Mechanical Engineers, New York AWWA American Waterworks Association, Denver, USA BHRA British Hydromechanics Group, Cranfield, UK CIRIA Construction Industry Research & Information Association, London CIWEM Chartered Institution of Water & Evironmental Management, London DoE Department of the Environment,-London FAO Food and Agriculture Organization, Rome HMSO Her Majesty's Stationery Office, London IAHS International Association of Hydrological Sciences, Wallingford, UK ICE Institution of Civil Engineers, London I Chem E Institution of Chemical Engineers, Rugby, UK IoH Institute of Hydrology, Wallingford, UK IWE/IWES Institution of Water Engineers &( Scientists), London IWSA International Water Supply Association, London NEWA New England Waterworks Association, Massachusetts, USA NERC Natural Environmental Research Council, Swindon, UK OFWAT Office of Water Services, Birmingham, UK SWTE Society for Water Treatment and Examination, London USGS United States Geological Survey, Washington, USA WHO World Health Organization, Geneva WMO World Meteorological Oganization, Geneva WRc Water Research Centre, Medmenham, UK 1 Public water supply requirement and sti measurement 1.1 Categories of consumption It is useful to divide public water consumption into the following categories. (1) Domestic In-house use- for drinking, cooking, ablution, sanitation, house cleaning, laundry, patio and car washing. Out-of-house use- for garden watering, lawn sprinkling and bathing pools. Standpipe use- from standpipes and public fountains. (2) Trade and industrial Industrial- for factories, industries, power stations, docks, etc. Commercial- for shops, offices, restaurants, hotels, railway stations, airports, small trades and workshops, etc. Institutional- for hospitals, schools, universities, government offices, military establish- ments, etc. (3) Agricultural Agricultural use is for crops, livestock, horticulture, greenhouses, dairies, farmsteads. )4( cilbuP Public use is for public parks, green areas, street watering, water mains and sewer flushing, fire-fighting. )5( sessoL Distribution losses- leakage from mains and so, vice pipes upstream of consumers' meters or property boundary; leaks from valves, hydrants and washouts, leakage and overflows from service reservoirs. Consumer wastage- leakage and wastage on consumers' premises and from their supply pipes, misuse or unnecessary use of water by consumers. Metering and other losses- source meter errors, supply meter errors, unauthorised or unrecorded consumption. 2 Public water supply requirement and its measurement Many domestic supplies are not metered. In the UK about 14% of domestic supplies in England and Wales were metered in 1999, but none in Scotland and Northern Ireland. A DoE report ~ mentions that in Denmark only town houses are normally metered; in the Netherlands about 24% of houses are unmetered; and in Germany only 30-40% of households are individually metered, the rest being block-metered. In the USA, whilst metering of domestic supplies si widespread, it is not universal. New York City did not start a programme to meter all domestic supplies until 1987. This was in response to the Delaware River Basin Commission's requirement that the major cities it supplies in the states of Delaware, New Jersey, New York and Pennsylvania, should achieve metering of all services within a ten year period. 2 A survey by the Asian Development Bank (ADB) in 36991 showed that, of 27 Asian cities serving over 1 million people, only 51 were fully metered and six metered less than 7% of their connections (Calcutta 0%: Karachi 1%). Trade and industrial supplies are usually metered because they are a major source of income to a water undertaking. In the UK many small shops and offices occupied only in the daytime used not to be metered, but now generally are, even though their consumption si small. Overseas standpipe supplies are not metered and are usually given free. The city of Bombay, for instance, supplies 400 M1/day (megalitres per day) to some 6 million people in its slums. 4 In many countries large quantities of water are used for watering public parks and green areas and supplying government offices and military establish- ments, etc. They are often not metered nor paid for if the government (or state or city) supplies the water. The result si that reported water distribution losses depend on the accuracy with which the unmetered consumption is estimated. 1.2 Levels of total consumption The usual measure of total consumption si the amount supplied per head of population; but in many cases the population served si not known accurately. In large cities there may be thousands of commuters coming in daily from outside; in holiday areas the population may double for part of the year. Other factors having a major influence on consumption figures are: (cid:12)9 whether the available supplies and pressure are sufficient to meet the demand, 24 hour or intermittent; (cid:12)9 the number of population using standpipes; (cid:12)9 the extent to which waterborne sanitation si available; (cid:12)9 the undertaking's efficiency in metering and billing, and in controlling leakage and wastage; (cid:12)9 how much of the supply goes to relatively few large industrial consumers; (cid:12)9 the climate. Some countries, such as India, rarely have any cities with a 24-hour supply. The ADB survey of 1996 already referred to 3 showed that 40% of 05 Asian cities surveyed did not have a 24-hour supply, and about two-thirds had street standpipe supplies. Hence comparison of average total consumption between undertakings si not informative. High consumption can be caused by large industrial demand and low consumption by a shortage of supplies. However the general range of total supplies per capita :si (cid:12)9 from 600 to 800 led (litres per capita per day) in the big industrial cities of USA; (cid:12)9 from 003 to 055 led for many major cities and urban areas throughout the world; 1.3 Consumption surveys 3 from 90 to 051 led in areas where supplies are short or there are many street standpipes, or many of the population have private wells. In England and Wales the average total supply was 288 lcd (1998/99). In Scotland it was 460 lcd and in Northern Ireland 407 led in 1997/98, mainly because these areas have a high rainfall providing plentiful supplies of good quality water. 3.1 Consumption surveys A consumption survey is necessary when losses appear to be large, or consumers in some areas cannot get an adequate supply, or metering and billing practices appear to be inefficient. This situation often occurs on many undertakings throughout the world where lack of money and technical resources has resulted in water supply systems where leakage and consumer wastage is high, and records of consumption are unreliable. In such a situation, it should be noted that: Total supply =Total legitimate potential demand plus consumer wastage and distribution losses minus unsatisfied demand. Hence the total supply can seem to be adequate when expressed as the water available per head of population, but this may conceal the fact that, due to excessive wastage and leakage, there is much unsatisfied demand because some consumers do not get the water they need. It is then necessary to conduct a consumption survey to find the state of the system. The steps involved are the following. (1) Log the initial state of the undertaking before any remedial work is started, by marking on a map of the distribution system areas where water pressure is too low for consumers to get what they need (a) at peak demand times, and (b) during the whole of the daytime. (2) Check the accuracy of source meters, e.g. by diverting the source output over a temporary measuring weir, or by measuring the input to a tank. (3) Check the general validity of supply meter readings by, for instance, check-reading a number of meters over a period and comparing with the readings billed. Find the typical number of supply meters found stopped at any one time, and investigate what billings are made when meters are found stopped. Find the average age of meters and how frequently they are brought in for testing and repair. Test some meters of typical size and age for accuracy. Where more than 15% of meters are found stopped at any one time, or many meters are over 01 years old and not brought in for testing and repair, a substantial amount of under-recording must be suspected. (4) Assess typical domestic consumption per capita by classifying dwellings into five or six classes, and test metering 30-35 dwellings typical of each class. (See Section 4.1 below.) (5) Test meter a few typical standpipes and, by estimating the population reliant on each, estimate the typical standpipe consumption per capita. (6) Examine the supply meters on all large trade and industrial supplies; check the accuracy of those found in poor condition. 4 Public-water supply requirement and its measurement List the largest potential trade consumers and check their billing records to see whether they seem reasonable having regard to the size of their supply pipe, their hours of take, and amount of water likely to be used for their production. It can be found that some major consumer is missed from the billings, or an establishment may have two supply feeds of which only one is metered. (7) Meter, or by some other means estimate, the amount of water supplied unmetered to such as government or municipal offices, and also to public parks and gardens to get a measure of their probable consumption. From the foregoing an estimate can be made of the probable total potential demand on the system in the following manner. On a map of the distribution supply districts, mark areas of the different classes of housing. Using appropriate population densities per hectare and measuring the areas of each class of housing within a district, estimate the total domestic demand per district by using the appropriate consumption per capita derived from Step 4. Add an allowance for unavoidable consumer wastage which will not have been registered by the test metering under Step 4. In each district any standpipe consumption should be added, and the trade and other non-domestic demands apportioned according to the character of the district and the location of major trade consumers. An allowance for a reasonable degree of unavoidable distribution leakage should be added, usually expressed as a percentage addition to the total domestic and trade demand for each district. This gives the total average daily demand on the whole system, broken down into sufficiently small supply districts for the demand in each district to be distributed to 'nodal points' of the mains layout, i.e. key junctions of mains. These 'nodaldemands' can then form the basis for an hydraulic analysis of flows in the distribution system, as described in Section 14.14. From this can be ascertained the adequacy of the distribution system to meet the demands. 1.4 Test metering in-house domestic consumption To assess average domestic consumption per person when supplies are not metered or records of metered domestic consumption are not reliable, it is necessary to test meter a sample of properties. It is best to rely on the results of test metering 30-35 households from each of five or six classes of households. Larger samples are difficult to conduct accurately because of the need to ensure all meters work accurately, all properties are leakfree, and the difficulty of keeping check of the number of people in each household. The households test metered should be typical of their class; they should not be chosen at random because the sample size is too small for random selection and could result in a bias of the sample mean towards the higher or lower end of the range within the class. Only about five or six classes of household should be adopted because it is difficult to distinguish between a larger range of households with any certainty. The test period should be 2-4 weeks, avoiding holiday times and, if possible, extremes of weather. Meter readings and occupancy rates should be ascertained weekly. Theoretically a sample size of at least 30 households is required to provide a reasonable estimate of the mean consumption in a given class of households. In practice 53 properties per class will need to be test metered to get a minimum of 30 valid results because of mishaps - a stopped meter, a leak discovered, or occupants gone away, etc. Unfortunately all such tests show a wide scatter of results, as illustrated in Fig. 1.1. The mean of a sample can therefore be substantially influenced by a few households where the 4.1 Test metering in-house domestic consumption 5 400 - 1484 (cid:12)9 412 ~529 489 465 350 - 300 - "ID g 250- "0 !._ .m 200- tl:l 0 175 Cl. t~ 150 - M M-~ .n _ _1 '" M 113 001 10 i75 M 77 L o M 57 50 M 15 mt 39 I (a) (b) Upper Middle Low Lowest Upper Middle Lowest Low ~ UK-----~ = Istanbul = = Egyptian------~ Egyptian village town Fig. 1.1 Variation of domestic consumption per capita within a given class of dwelling. UK: (a) 1-2 occupancy and low number of water consuming appliances; )b( 2-4 occupancy in mainly detached houses with high number of appliances. Data from Russac D. A. ,.V Rushton, K. R. and Simpson, R. J. Insights into domestic demand from a metering trial. JIWEM, June 991 l, pp. 342-351. Istanbul and Egyptian data from Binnie and Partners' Reports. consumption seems extraordinarily high. Provided such high consumption is not due to meter reading error, these figures should not be excluded because domestic consumption is so highly variable. The problem is, however, that the sample size is too small to evaluate the incidence of such high consumers which may be, for example, one in 20, so that a sample size of 30 may contain no such high consumers, or one or two. However, if five classes of housing are adopted there will be at least five separate samples from which to judge, roughly, the frequency of such exceptional consumption. The mean value of per capita consumption should be the total consumption in the 30 or so households tested in a given class, divided by the total occupancy during the test period, because the total domestic demand is estimated on the basis of the population in each class of housing.

See more

The list of books you might like

Most books are stored in the elastic cloud where traffic is expensive. For this reason, we have a limit on daily download.