Upgrade, Renovation, & Add

145 Pages·2015·11.45 MB·English

BOARD OF COUNTY COMMISSIONERS
[phone]
John E. Manning April 8, 2015
District One
Cecil L. Pendergrass
SOLICITATION NO.: B-150083
District Two
Larry Kiker
District Three SUBJECT: ADDENDUM NUMBER TWO
Brian Hamman
District Four REFERENCE: Upgrade, Renovation, & Addition to the Public Safety
Frank Mann Communications’ Building Emergency Power System
District Five
Roger Desjarlais
The following changes shall become a part of the Bid Documents and shall be as
County Manager
binding as if contained therein:
Richard Wesch
County Attorney
ITEM NO. 1
Donna Marie Collins
County Hearing CHANGE- BID OPENING DATE
Examiner
The bid opening date and time is being changed FROM Tuesday, April 14,
2015 at 2:30 p.m. TO Tuesday April 21, 2015 at 2:30 p.m.
ITEM NO.2
CHANGE
1. The new contract duration and completion dates are as follows:
Substantially complete in 150 consecutive calendar days from date of official
notice to proceed
Final completion in 180 consecutive calendar days from the date of official
notice to proceed
2. Per diem liquated damages is $465.00 for each day of delay in achieving
substantial completion as set forth herein.
3. Change the following statement under the heading “GENERAL INFORMATION”
(Page 25):
FROM-“The County prefers that the removal and restoration of walls and other
fixed appurtenances be kept to a minimum.”
TO- “The County prefers that the removal and restoration of fixed
appurtenances be kept to a minimum.”
P.O. Box 398, Fort Myers, Florida 33902-0398 [phone]
lee-county.com
Recycled Paper AN EQUAL OPPORTUNITY AFFIRMATIVE ACTION EMPLOYER
Solicitation No. B-150083- Addendum No. Two (Continued)

4. Change the following statement under the heading “BASIS OF
AWARD” (Page 25):

FROM- “NOTE: There will be NO change orders allowed or approved
under this bid”

To- “NOTE: Any and all desired changes to the scope of work outlined
herein shall be presented to the project manager for review and
approval”

ITEM NO. 3
DELETE Page 13
REPLACE with page 13A (Enclosed)

DELETE Page 18
REPLACE with page 18A (Enclosed)

REPLACE Sheet-E000 LEGEND AND GENERAL NOTES-
ELECTRICAL with Sheet- E000 LEGEND AND GENERAL
NOTES ELECTRICAL DATED 04/06/15 (Enclosed)

REPLACE Sheet-E001-SITE PLAN-ELECTRICAL with Sheet- E001-
SITE PLAN-ELECTRICAL DATED 04/06/15 (Enclosed)

REPLACE Sheet-E001-SITE PLAN-ELECTRICAL with Sheet- E001-
SITE PLAN-ELECTRICAL DATED 04/06/15 (Enclosed)

REPLACE Sheet-E101-ENLARGED FLOOR PLANS- POWER with
Sheet- E101- ENLARGED FLOOR PLANS- POWER
DATED 04/06/15 (Enclosed)

REPLACE Sheet-E201-DEMO RISER DIAGRAM & LEGEND-
ELECTRICAL with Sheet- E201- DEMO RISER DIAGRAM
& LEGEND-ELECTRICAL DATED 04/06/15 (Enclosed)

REPLACE Sheet-E202-NEW RISER DIAGRAM & LEGEND-
ELECTRICAL with Sheet- E202- NEW RISER DIAGRAM &
LEGEND-ELECTRICAL DATED 04/06/15 (Enclosed)

REPLACE Sheet-C000-COVER SHEET with Sheet- C000-COVER
SHEET DATED 04/06/15 (Enclosed)

P.O. Box 398, Fort Myers, Florida 33902-0398 [phone]
Recycled Paper AN EQUAL OPPORTUNleITeY- cAoFuFnIRtyM.cAoTmIVE ACTION EMPLOYER
Solicitation No. B-150083- Addendum No. Two (Continued)

ITEM NO.4
ADDITION

1. Add Cummins Power South Submittal dated October 1, 2014
(Enclosed)

2. Add Cummins 40KVA UPS bid specifications (Enclosed)

3. Doors and frames that will need to be removed shall be replaced the
same day. The front door has an electric hinge and a card reader, any
work on said door will need to be coordinated with the project manager
prior to commencement.

BIDDER IS ADVISED, YOU ARE REQUIRED TO ACKNOWLEDGE
RECEIPT OF THIS ADDENDUM WHEN SUBMITTING A BID. FAILURE
TO COMPLY WITH THIS REQUIREMENT MAY RESULT IN THE
BIDDER BEING CONSIDERED NON-RESPONSIVE. ALL OTHER
TERMS AND CONDITIONS OF THE BIDDING DOCUMENTS ARE AND
SHALL REMAIN THE SAME.

Patrick T. Lewis Sr.
Patrick T. Lewis Sr.
Procurement Analyst
Lee County Procurement Management

P.O. Box 398, Fort Myers, Florida 33902-0398 [phone]
Recycled Paper AN EQUAL OPPORTUNleITeY- cAoFuFnIRtyM.cAoTmIVE ACTION EMPLOYER
FORMAL BID NO.: B-150083
LEE COUNTY, FLORIDA
PROPOSAL QUOTE FORM
FOR
UPGRADE, RENOVATION, & ADDITION TO THE PUBLIC SAFETY COMMUNICATIONS BUILDING
EMERGENCY POWER SYSTEM
DATE SUBMITTED: ____________________________________
VENDOR NAME:
TO: The Board of County Commissioners
Lee County
Fort Myers, Florida
Having carefully examined the “General Conditions”, and the “Detailed Specifications”, all of which are contained
herein, the Undersigned proposes to furnish the following which meet these specifications:
1. The Undersigned, hereinafter called "BIDDER", having visited the site of the proposed project and having
become familiar with the local conditions, nature and extent of the work, and having examined carefully the
Agreement Form, General Conditions, Supplementary Conditions, Plans and Specifications and other Contract
Documents, and having fulfilled their requirements as well as the Bonding requirements herein, proposes to furnish all
labor, materials, equipment and other items, facilities and services for the proper execution and completion of the:
UPGRADE, RENOVATION, & ADDITION TO THE PUBLIC SAFETY COMMUNICATION
BUILDING EMERGENCY POWER SYSTEM
in full accordance with the drawings and specifications prepared in accordance with your Advertisement for Bids,
Instruction to Bidders, Construction Contract and all other documents related thereto on file with Lee County Division
of Procurement Management, and if awarded the contract, to complete the said work within the time limits specified
for the following bid price:
TOTAL LUMP SUM AMOUNT __________________________________________ ($______________)
(Written in words)
2.There is enclosed a Certified Check, Cashier's Check or Bid Bond (paper or electronic format) in the amount of
5% of bid, payable to the Lee County Board of County Commissioners as a guarantee for the purpose set out
in the Instruction to Bidders.
3. The BIDDER hereby agrees that:
(a) The above proposal shall remain in full force and effect for a period of 90 calendar days after the time of the
opening of this proposal and it shall not be revoked, withdrawn or canceled within that time frame. Once the
bidder has been notified that his bid has been awarded by the Board of County Commissioners, within the
above time frame the price proposed as submitted shall constitute the contract price which shall be executed
within the time frames established by these documents.
(b) In the event the award is made to this BIDDER, the BIDDER will enter into a formal written agreement with the
COUNTY in accordance with the accepted bid, will execute the contract contained within these documents,
and provide a Public Payment and Performance Bond from a Surety in good standing with the Florida
Department of State who is licensed to do business in Florida and acceptable to the OWNER. The Public
Payment and Performance Bond shall be in the amount of one hundred percent (100%) of the accepted bid.
The BIDDER shall, within seven calendar days of the Notice of Award, submit the required Certificates of
Insurance. The BIDDER further agrees that in the event of the BIDDER'S default of breach of any of the
agreements of this proposal, the bid deposit shall be forfeited.
NOTE REQUIREMENT: IT IS THE SOLE RESPONSIBILITY OF THE VENDOR TO CHECK LEE
COUNTY PROCUREMENT MANAGEMENT WEB SITE FOR ANY PROJECT ADDENDA ISSUED FOR
THIS PROJECT. THE COUNTY WILL POST ADDENDA TO THIS WEB PAGE, BUT WILL NOT
NOTIFY.
13A
FORMAL BID NO.: B-150083
LEE COUNTY
CONTRACTORS QUALIFICATION QUESTIONNAIRE
THIS FORM SHOULD BE COMPLETED AND SUBMITTED WITH THIS BID PACKAGE. FAILURE TO
SUBMIT THIS QUESTIONNAIRE MAY BE GROUNDS TO BE DECLARED NON-RESPONSIVE.
Submitted By:
� Corporation - Date of Incorporation State of Incorporation:
If Out of State Corporation, currently authorized to do business in Florida, give date of such authorization:
� Partnership - Date of Organization: Nature of Partnership: General
Limited
Association
� Individual - Name and Address of Owner
� Joint Venture - Between:
Name Title
And:
Name Title
Date of Agreement:
� Other - Explain
Parent Company Office Address (if any):
Principal Office Address:
Name of Project (if applicable):
Person to Contact:
Title: Telephone No.:
Type of Work (file separate form for each classification of work):
General Contractor: Road Repair:
Underground Utilities: Heavy Construction:
Road Building: Other (specify):
The signee of this questionnaire guarantee, as evidenced by the sworn affidavit required herein, the truth and accuracy
of all statements and of all answers to interrogatories hereinafter made.
The undersigned hereby authorizes and requests any public official, engineer, architect, surety company, bank
depository, material or equipment manufacturer or distributor or any person, firm or corporation to furnish any
pertinent information requested by Lee County Government deemed necessary to verify the statements made in this
application or regarding the standing and general reputation of the Bidder.
1. How many years has your organization been in business as a Electrical Contractor under your present
name?
2.Under what other or former names has your organization operated?
18A
GENERATOR YARD
71
0
15 0
GENERATOR #2 5 R: 0
500KW SPD 11 BE 01.
8 0
M

1600A NU P1
P 5
2
A
SPD R 4
4
T
4 S 21
5 4
15
GENERATOR FRAME GROUNDED
AT EACH CORNER WITH #2/0 AWG
SOLID CU AND BURIED BELOW
GRADE, BOND TO COUNTERPOISE.
SEE SITE PLAN.
S
5
T
MDP 2000A N 0
RATED 208/120V E 9
3
M
3
15 E S
5 V N A
GENERATOR #1 4 11 O D
4 - #1/0 & #6 GND, 2" C. O
SPD 22 KAIC 200A 4 - #1 & #8 GND, 1 1/2" C. R ATI RI
1600A 25 KAIC 60A SPD MP NIC NUE FLO
I U E
22 KAIC 200A PROVIDE NEW CB. MATCH EXISTING SQ. D. L M V Y,
SPD 60A TYPE, USE EXISTING SPACE IN SWBD. A OM A NT
10 KAIC C C Z U
5 15 60A RI Y RTI O
1402 KKAAIICC 400A ELECTRICAL ROOM DISPATCH ECT AFET 65 O EE C
400A L S 6 L
42 KAIC E
C 2 S,

3P/150A D LI R
42 KAIC B E
E
22 KAIC 200A TO BLDG A 4 - #1/0 & #6 GND, 2" C. OS PU MY

1 150A SPARE P T
25 KAIC R
8 ATS #1 200A TO BLDG A O O
11 22 KAIC R F
6 P
N E 150A
42 KAIC
L SPD
200A
6 10 KAIC DISPATCH
FTPRLANSFORMER CMTETER SPD 16650 K0AAIC 11 42 KAIC 200A AU/NCIT #1 AU/NCIT #2 NPOOWRMERAL "N" PANEL "B" PANEL "MDP-1" PANEL "ME" PANEL "C" PUAPNS E#L1 PUAPNS E#L1B PUAPNS E#L1C PUAPNS E#L2 5 5
SPD
UPS #1 9
AVAILABLE FAULT 8 ATS #2 40KVA UPS #2 7 GENERATOR #1 GENERATOR #2
IS 23,187A PER FPL. RD 125A 14 RATED 40KVA 100A REMOTE REMOTE
A RATING
N E O Y 100A ANNUNCIATOR ANNUNCIATOR
L SPD 12 T SPD SPD SPD 8 SPD DISPATCH N
G
13 PD PUAPNS E2LA KI ESI
S D 6
S & 0
3 11 3 W N 6
O 2
12 12 E TI 01
T C
TO MAIN BUILDING 1 NI C TRU R 0
10 COPPER GROUNDING GROUNDING BONDS #1/0 THWN CU S E NS A
O
BUS IN BUILDING 2 I T C O.
W F N
I O
H NT SE
TO BLDG B M. C E N
1 TO GENWATCH M E
APPROX. 6 FEET A(P2)A 5R/T8." #G1R/0O CUUN DE XROOTDHSE SRPMAACLELDY 2 MAIN BUILDING SERVERS R ART LIC
WCEOLRDNEDER T OO FG MRAOIUNN BDU RILODDINSG. LBOECHAINTDED E LAETC STORUICT HRWOEOSMT. EXISTING SQUARE D NON-FUSED TBOO NGDRSO IUNN RDAINDGIO ER A DEP DA
SAFETY SWITCH,
DOUBLE THROW MODEL #82254 BUILDING T TY RI
N O
1 E OU L
C F
P
E
E
EXISTING MANUAL L
TRANSFER SWITCH TO
KEYNOTES: PORTABLE GENSET GROUNDING GRID (TYPICAL)
CEB CEB
SERVICE "A" SERVICE "B" PANEL "A" PANEL "B" PANEL "C"
1 #1/0 CU GROUNDING CONDUCTOR MUST BE RE-WELDED TO THE 60A
GROUND RODS AND TESTED TO ENSURE CONTINUITY. UPS "A" UPS "B" UPS "C"
80A
COPPER GROUNDING
100A
2 THE LOCATIONS OF GROUND RODS SHALL BE CONFIRMED G E 150A 125A PLATE IN BUILDING
(TYPICAL)
AND THE RESISTANCE OF THE GROUNDING ELECTRODE TESTED,
EXISTING 200A 225A
USING FALL OF POTENTIAL TEST. IF THE RESISTANCE IS DETERMINED N
CAMLOK BOX
TO BE GREATER THAN 5 OHMS, ANOTHER GROUND ROD SHALL BE DRIVEN.
D D
P P
3 PROVIDE GROUNDING BOND TO EXISTING GRID. S S
SINGLE GROUND ROD INSTALLED
4 CONTROL WIRING, FIBER OPTIC CABLE, PER MANUFACTURER'S EXTERIOR OF RADIO BUILDING
REQUIREMENTS. ROUTE IN CONDUIT. FOR SERVICE TO REMOTE
ANNUNCIATORS. PROVIDE FIBER OPTIC REPEATER AT EACH
TERMINATION POINT, FOR FIBER INTERFACE TO GENERATOR SET
RADIO BUILDING
CONTROLLER AND REMOTE ANNUNCIATOR.
PROVIDE DC TRANSFORMER FOR POWER SUPPLY TO REMOTE
5
vt ANNUNCIATOR, CONTROL INTERCONNECTION VIA FIBER CABLE.
r
er. COORDINATE EXACT REQUIREMENTS WITH GENERATOR SET
us SUPPLIER, PRIOR TO ORDERING EQUIPMENT. PROVIDE 120V, 20A
ha CIRCUIT FROM NEW PANEL UPS-2A FOR POWER TRANSFORMER.
k.
mar 6 INSTALL EXISTING SPD AT NEW SERVICE DISCONNECT LOCATION. NEW RISER DIAGRAM - ELECTRICAL
_
4
1 100A, 208/120V, 3-PHASE/4-WIRE, 42 POLE PANEL. 100A MCB, RECESS NOT TO SCALE
R 7
_ MOUNTED. PROVIDE BRANCH BREAKERS TO MATCH EXISTING UPS #2 -
L
A DISPATCH PANEL BEING DEMOLISHED. REFER TO DEMO RISER
R
T DIAGRAM. APPROXIMATE BRANCH BREAKER QUANTITIES AS FOLLOWS,
N CONTRACTOR SHALL VERIFY ON SITE PRIOR TO BID: (2) IP-30A, (37) IP-
E
C 20A, WITH (1) 3P-30A TO SERVE SPD.
P
E
M 8 EQUIPMENT FURNISHED BY OWNER. INSTALLED BY CONTRACTOR.
_
1
3 225A, 208/120V, 3-PHASE/4-WIRE, 42 POLE PANEL. 150A MCB, SURFACE DATE ISSUED
0 9
14 MOUNTED. PROVIDE BRANCH BREAKERS TO MATCH EXISTING UPS #2 FEBRUARY 02, 2015
7 PANEL BEING DEMOLISHED. REFER TO DEMO RISER DIAGRAM.
s\ REVISIONS
nt APPROXIMATE BRANCH BREAKER QUANTITIES AS FOLLOWS,
me CONTRACTOR SHALL VERIFY ON SITE PRIOR TO BID: (33) IP-20A, (1) 2P- 1 ADDENDUM 2 04/06/15
u 30A, WITH (1) 3P-30A TO SERVE SPD, (1) 3P-100A SUB-FEED TO SERVE
c
o PANEL UPS-2A.
D
er\
s 10 4 SETS, 4-600KCMIL, 4 - 3 1/2" C. SERVICE ENTRANCE.
u
a
h
k. 11 4 SETS, 4-600KCMIL & #4/0 GND, 4 - 3 1/2" C.
ar NEW RISER
m
s\ 12 NEW SPD. MATCH EXISTING DEVICES. MANUFACTURED BY DIAGRAM &
er TRANSTECTOR, APEX IMAX MODEL.
s
U LEGEND -
C:\ 13 PROVIDE 2P-30A CB IN EXISTING SPACE TO SERVE NEW GENERATOR Brett L. Sands, P.E.
COOLANT HEATER. MATCH SWITCHBOARD MANUFACTURER MODEL ELECTRICAL
Florida License #48477
AND AIC RATING. REFER TO SITE PLAN FOR ADDITIONAL
REQUIREMENTS.
PROVIDE 1P-20A CB IN EXISTING SPACE TO SERVE NEW GENERATOR
14
BATTERY CHARGER. MATCH PANEL MANUFACTURER MODEL AND AIC 13099 S. Cleveland Ave.
M
P RATING. Suite 500
8 SHEET NUMBER
4 Fort Myers, Florida 33907
1: 15 PROVIDE SURGE PROTECTION DEVICES FOR ALL LOW VOLTAGE
3 CABLING ENTERING BUILDING, TYPICAL. MANUFACTURED BY EDCO OR Phone: [phone]
1:
5 EQUAL. Fax: [phone] E202
1 www.tlc-engineers.com
0
2 ©Copyright 2014TLC Engineering for Architecture, Inc.
6/
4/ EB #0000015 TLC NO: 714031 Seal
71
0
0
R: 0
PROVIDE TEMPORARY BE 01.
BOND TO EXISTING MAIN 0
M
SERVICE GROUND
NU P1
GENERATOR YARD P 5
2
A
R 4
7 4 T 4
S 21
N
TO MAIN BUILDING
L GROUNDING BONDS
E
3
MDP 2000A
208/120V
PORTABLE 3
S
GENERATOR 5
T
0
N
E 9
200A M 3
22 KAIC 3
3 60A VE NS A
25 KAIC SPD O D
O
22 KAIC 200A R ATI RI
E P C E O
MANUAL L 10 KAIC 60A M NI NU FL
I U E
TRANSFER N 10 KAIC 60A L M V Y,
SWITCH ELECTRICAL ROOM DISPATCH A M A T
GENERATOR #1 1 42 KAIC 400A C CO IZ UN
1600A 400A RI Y RT O
125 KAIC 42 KAIC C
42 KAIC 400A SPARE TOEEXFMI SPPTAOINNREGAL R PFAYON EREN LTC EULMPOPSSO E#R2DA FBRERYEE DFAEEKREED RR., A MTTAAINTPGC BH.US TWTEOIRM UEPP/OCSRO PANARDNYUE IFLTE #SE2ID ZDEEUR. RT MIONA GMT CARIHEN PTELAXAIINSC TESIMNEREGNVITC OEF ECT AFET 65 O EE
6 22 KAIC 200A TO BLDG A EXISTING UPS #2. EL C S 26 S, L
SPD REMOVE 150A D LI R
EXIST. 25 KAIC B E
E
GATE NEEARCAHT COORR FNREARM WE IGTHR O#2U NADWEGD 28050 K0AAIC 22 KAIC 125000AA TO BLDG A RBYEPMAOSVSE S EWXIITSCTH. POS PU T MY
SOLID CU AND BURIED BELOW GRADE 42 KAIC R
O
10 KAIC 200A REMOVE 5 R FO
FPL CT DISPATCH EXIST. P
TRANSFORMER METER 6 42 KAIC 200A AU/NCIT #1 AU/NCIT #2 NPOOWRMERAL "N" PANEL "B" PANEL "MDP-1" PANEL "ME" PANEL "C" PUAPNS E#L1 PUAPNS E#L1B PUAPNS E#L1C PUAPNS E#L2 UPS #2 5
REMOVE
SPD REMOVE N E UPS #1 EXIST.
AVAILABLE FAULT EXIST. 40KVA 25 KVA REMOVE
IS 23,187A PER FPL. 110200 0KAAIC L O YARD 110205AA RATED 25S7HIS EU18XPKISSV T#A2. 100A 60A
T SPD SPD SPD RATING UPS LOAD REMOVE EXIST.
5
CENTER DISPATCH
PD PANEL
S
N
G
KI SI
E
D 6
#1/0 THWN CU S & 0
W N 6
2 COPPER GROUNDING O 2
PLATE IN BUILDING E T CTI 01
TYPICAL) I C RU 0
N T R
TO BLDG B S E ONS A
1 TO GENWATCH I T C O.
(AWC2POE) PR5LR/DN8OEE" XDGR. R TO6OO FFU EGMNERADTOI N RAU OPBNUADDRIS LRT DSO. IP#NDA1GS/C0 .B E LCEDOUHC IENAXDTOE ETDLH EAECTR TSMROAICUL LTRYHOWOEMS.T 2 ESXAIFSETTINYG S WSQITUCAHR,E D NON-FUSED MAIN BUILDING SERVERS TBOO NGDRSO IUNN RDAINDGIO M. W CHI MENT OF ENSE N
DOUBLE THROW MODEL #82254 BUILDING R ART LIC
1 R A EP A
E D D

EXISTING MANUAL T TY RI
N O
TRANSFER SWITCH TO E OU L
KEYNOTES: PORTABLE GENSET G(TRYOPIUCNADLI)NG GRID P C F
CEB CEB EE
SERVICE "A" SERVICE "B" PANEL "A" PANEL "B" PANEL "C" L
1 #1/0 CU GROUNDING CONDUCTOR MUST BE RE-WELDED TO THE 60A
GROUND RODS AND TESTED TO ENSURE CONTINUITY. UPS "A" UPS "B" UPS "C"
80A
COPPER GROUNDING
100A
2 THE LOCATIONS OF GROUND RODS SHALL BE CONFIRMED G E 150A 125A PLATE IN BUILDING
(TYPICAL)
AND THE RESISTANCE OF THE GROUNDING ELECTRODE TESTED,
USING FALL OF POTENTIAL TEST. IF THE RESISTANCE IS DETERMINED EXISTING N 200A 225A
CAMLOK BOX
TO BE GREATER THAN 5 OHMS, ANOTHER GROUND ROD SHALL BE DRIVEN.
D D
P P
3 PROVIDE TEMPORARY SERVICE FLEXIBLE CABLING, FOR MAINTAINING S S
EMERGENCY AND NORMAL SERVICE TO MDP DURING RENOVATION.
SINGLE GROUND ROD INSTALLED
2000 AMP RATING. COORDINATE EXACT ROUTING OF CABLING WITH
EXTERIOR OF RADIO BUILDING
OWNER PRIOR TO INSTALLATION. PROTECT IN PLACE DURING ENTIRE
DURATION OF RENOVATION. SEE KEYNOTE 4 THIS SHEET, AND SITE
PLAN, FOR ADDITIONAL INFORMATION. THIS WORK WILL BE
RADIO BUILDING
COMPLETED PRIOR TO BEGINNING DEMOLITION INSIDE BUILDING.
PROVIDE TEMPORARY AUTOMATIC TRANSFER SWITCH, 2000 AMP,
4
NEMA 3R ENCLOSURE. INSTALL ON CONCRETE PAD. SEE KEYNOTE 3
THIS SHEET, AND SITE PLAN, FOR ADDITIONAL INFORMATION. THIS
WORK WILL BE COMPLETED PRIOR TO BEGINNING DEMOLITION INSIDE
BUILDING.
vt
er.r 5 PROVIDE FOR PHASED SEQUENCE FOR TRANSFER OF EXISTING DEMO RISER DIAGRAM - ELECTRICAL
s CIRCUITS TO NEW PANEL, TO AVOID OUTAGES TO EXISTING SYSTEMS,
u
ha PRIOR TO DEMOLITION OF PANEL AND FEEDERS. COORDINATE WITH NOT TO SCALE
k. OWNER THE EXACT SEQUENCE OF WORK, IN ADVANCE OF BEGINNING
ar ANY WORK.
m
_
4
1 6 RELOCATE EXISTING. SEE NEW WORK RISER AND FLOOR PLAN.
R
_
AL 7 PROVIDE TEMPORARY MAIN DISCONNECT, 2000 AMP CIRCUIT BREAKER,
R NEMA 3R ENCLOSURE, ON CONCRETE PAD. SEE KEYNOTES 3 AND 4
T
N THIS SHEET FOR ADDITIONAL INFORMATION.
E
C
P
E
M
_ 1
1
3 DATE ISSUED
0
14 FEBRUARY 02, 2015
7
s\ REVISIONS
nt
me 1 ADDENDUM 2 04/06/15
u
c
o
D
er\
s
u
a
h
k.
ar DEMO
m
s\ RISER
er
s
U DIAGRAM &
C:\ Brett L. Sands, P.E.
LEGEND -
Florida License #48477
ELECTRICAL
13099 S. Cleveland Ave.
M
P Suite 500
0 SHEET NUMBER
5 Fort Myers, Florida 33907
1:
3 Phone: [phone]
1:
5 Fax: [phone] E201
1 www.tlc-engineers.com
0
2 ©Copyright 2014TLC Engineering for Architecture, Inc.
6/
4/ EB #0000015 TLC NO: 714031 Seal
GENERAL DEMOLITION NOTES:
1. ALL EXISTING CONDITIONS MUST BE VERIFIED PRIOR TO BID. FIELD CONDITIONS
SHALL GOVERN.
2. ALL EXISTING POWER EQUIPMENT, LIGHTING, WIRING, AND ASSOCIATED
CONDUIT WITHIN THE PROJECT AREA SHALL REMAIN, UNLESS NOTED 71
OTHERWISE. COORDINATE WITH THE COUNTY PROJECT MANAGER PRIOR TO 0
REMOVAL. 0
R: 0
3. TCHOEN TDREAMCOTLOITRIO WNI TSHC OA PGEE DNEESRCARL IKPNTOIOWNL IESD INGTEE ONFD TEHDE T OAR PERAO OVFID DEE TMHOELITION BE 01.
0
WORK. ANY DISCREPANCIES SHALL BE BROUGHT TO THE ATTENTION OF THE M

ENGINEER. THE CONTRACTOR IS RESPONSIBLE FOR ALL REQUIRED DEMOLITION NU P1
WHETHER SHOWN ON THE PLANS OR NOT. P 5
2
4. ALL CONDUITS SERVING OTHER SPACES OR FLOORS THAT RUN THROUGH THE A
R 4
PROJECT AREA SHALL REMAIN ACTIVE DURING CONSTRUCTION, SO AS NOT TO 4
T
CAUSE ANY DISRUPTION TO THESE OTHER SPACES. IT IS THE CONTRACTOR'S S 21
RESPONSIBILITY TO ENSURE THAT ALL CONDUITS, NEW OR EXISTING, WITHIN
THE PROJECT AREA ARE PROPERLY SUPPORTED AND PROVIDED WITH BONDING
BUSHINGS IN ACCORDANCE WITH THE 2008 NATIONAL ELECTRICAL CODE.
5. ALL ITEMS REMOVED UNDER THIS PROJECT SHALL BE DISPOSED OF OR TURNED
OVER TO THE OWNER AT THE OWNER'S DISCRETION.
P. M CLOSET P. M CLOSET S 5
T
UI O UI O N 0
Q O Q O E 9
3
E R E R M 3
E S
A
V N
O D
EQUIP. EQUIP. O
R TI RI
ROOM ROOM P CA E O
M NI NU FL
I U E
L M V Y,
A M A T
O N
C Z
C U
I
RI Y RT O
C
T T O
C E E
F 5
UPS PANEL #1 1 UPS PANEL #1 E A 6 E
(TO REMAIN) UPS PANEL #2 1 4 L S 6 L
E
C 2 S,

UPS PANEL #1C 1 PANEL UPS #2 UPS PANEL #1C UPS LOAD 1 D BLI ER
4 (TO REMAIN) CENTER E U Y
S P M
O

P T
R
O
O
R
F
P
UPS #2 1
ABANDONED SERVICE
1 BYPASS 1 DISONNECT SWITCH 1
SWITCH
T BATTERY
UPS #2 6 5
PACK
ISOLATION 1
MDP 1 1 MDP
XFMR
1
OFFICE OFFICE
1
7'-8" CLEAR
UPS #1 UPS #1
N
BELOW WIREWAY G
1 KI SI
MECHANICAL MECHANICAL E
D 6
/ / S & 0
ELECTRICAL ELECTRICAL W N 6
O 2
ROOM ROOM E T CTI 01
AHU ATS #2 AHU I C RU 0
1 N T R
6 S E NS A
O
SPD 6'-7" CLEAR I T C O.
1 BELOW WIREWAY W I OF N
EQUIP. EQUIP. EXTE M. CH ENT NSE
ROOM EXTENT 1 ROOM NT OF FR EGXEINSETRINAGTOR ATS 1 R AR EPARTM A LICE
O (4) 4" EMPTY C. TO OUTSIDE. EE E D D
F FRE CAP AT EXTERIOR. AREA T NTY ORI
E ARE ATS #1 . HVA 1 12" x 12" PE COU FL
A C WIREWAY E
. H 6 SY LE
V S
A T
C S SPD EM PANEL ME 3
Y S
S B
EQUIP. TEM 3 5 PANEL ME 1 EQUIP. EYO
S N SPD 3
ROOM B ROOM D EXISTING
E 1 1
Y UTILITY GENERATOR 1200 AMP
O 1
ND MAIN 6 SPD 1 MAIN EXISTING
FP&L MAIN GATE I/C
J-BOX 3
SPD
3 5 SPD GATE I/C J-BOX 1 SPD 2 2 SPD
AREA WHERE
1
OSP CABLES AND FIBER
ENTER BUILDING
ELECTRICAL KEY NOTES NEW WORK ELECTRICAL KEY NOTES DEMO
rvt # KEY NOTE TEXT # KEY NOTE TEXT
er.
us 1 EXISTING EQUIPMENT TO REMAIN. EXISTING EQUIPMENT TO BE REMOVED. REFER TO DEMOLITION RISER DIAGRAM
ha 1 AND PHASING NOTES FOR TEMPORARY SERVICE REQUIREMENTS, TO MINIMIZE
k. OUTAGES. REMOVE ASSOCIATED WIRE BACK TO SOURCE.
ar NEW PANEL. SEE DEMOLITION PLAN AND RISER DIAGRAMS FOR
m 2
REQUIREMENTS OF PANEL "ME".
_
4 2 DEVICE TO BE REUSED, RELOCATE AS REQUIRED. SEE POWER PLAN.
1
R
_ 3 NEW LOCATION OF EXISTING DEVICE. SEE DEMOLITION PLAN.
L
A 3 EXISTING TO REMAIN.
R
T NEW PANEL. REFER TO DEMOLITION FLOOR PLAN AND RISER DIAGRAM FOR
N 4
PHASING AND TEMPORARY SERVICE REQUIREMENTS.
E EXTEND AND RECONNECT ALL EXISTING BRANCH CIRCUITS TO NEW PANEL UPS
C
P 4 #2, PRIOR TO DEMOLITION. REFER TO POWER PLAN AND RISER DIAGRAMS FOR
E 5 RECONNECT TO NEW EQUIPMENT, RELOCATE AS REQUIRED. ADDITIONAL REQUIREMENTS.
M
_
1
3 PROVIDE FOR REMOVAL AND REPLACEMENT OF DOORS/DOOR FRAME, AND DATE ISSUED
0 6 PROVIDE NEW CONCRETE PAD FOR ALL NEW EQUIPMENT.
14 5 MECHANICAL DUCTWORK, AS REQUIRED TO ALLOW MOVING NEW EQUIPMENT FEBRUARY 02, 2015
7 INTO ELECTRICAL ROOM.
s\ REVISIONS
nt 1
me 1 1 ADDENDUM 2 04/06/15
u
c
Do ENLARGED FLOOR PLAN - POWER ENLARGED FLOOR PLAN DEMO - POWER
er\ 2 1
s
u 1/4" = 1'-0" 1/4" = 1'-0"
a
h
k.
ar ENLARGED
m
s\ FLOOR
er
s
U PLANS -
C:\ Brett L. Sands, P.E.
POWER
Florida License #48477
13099 S. Cleveland Ave.
M
P Suite 500
1 SHEET NUMBER
5 Fort Myers, Florida 33907
1:
3 Phone: [phone]
1:
5 Fax: [phone] E101
1 www.tlc-engineers.com
0
2 ©Copyright 2014TLC Engineering for Architecture, Inc.
6/
4/ EB #0000015 TLC NO: 714031 Seal
ELECTRICAL KEY NOTES
4 # KEYED NOTE TEXT
E001 1 EXISTING 500 KW GENERATOR TO REMAIN. SHOWN HERE FOR REFERENCE.
2 NEW 500 KW CUMMINS GENERATOR FURNISHED BY OWNER. PROVIDE CONCRETE PAD
AND INSTALL COMPLETE GENERATOR. REFER TO PAD DETAILS THIS SHEET. 71
0
UPS 1 11 3 EXISTING ELECTRICAL EQUIPMENT ROOM. SHOWN HERE FOR REFERENCE. SEE
0
ENLARGED PLAN FOR DETAILS. R: 0
UPS 2A UPS 2 12 4 EXISTING SITE COUNTER-POISE SHOWN FOR REFERENCE. TEST COUNTER-POISE PRIOR BE 01.
TO UNDERGROUND WORK COMMENCING AND AGAIN WHEN FINISHED. ALL EXCAVATION IN 0
M
13 THE AREA OF THE EXISTING COUNTER-POISE TO BE DONE BY HAND. NU P1
5 PROPOSED ROUTING OF NEW, REVISED UNDERGROUND FEEDERS FROM EXISTING P 5
GENERATOR TO NEW ATS #1 IN ELECTRICAL ROOM (SEE KEYNOTE #3). 2
A
6 ROUTING OF FEEDERS FROM NEW GENERATOR TO NEW ATS #1 IN ELECTRICAL ROOM R 4
4
(SEE KEYNOTE #3). T
S 21
7 APPROXIMATE LOCATION OF CAMLOCK BOX FOR PORTABLE GENERATOR HOOK-UP.
PART PLAN - ELECTRICAL CONTRACTOR MAY UTILIZE THIS CONNECTION FOR TEMPORARY SERVICE. SEE KEYNOTE
25.
2 1
8 REMOVE EXISTING MANUAL TRANSFER SWITCH. REFER TO RISER DIAGRAM AND PHASING
1/8" = 1'-0"
NOTES FOR ADDITIONAL INFORMATION.
9 EXISTING PORTABLE GENERATOR, TO BE REMOVED BY OWNER.
10 EXISTING FPL UTILITY TRANSFORMER. COORDINATE ALL ASSOCIATED WORK, S
5
SECONDARY FEEDER REPLACEMENT, WITH FPL, IN ADVANCE. CONTACT: ERIC WALTHER, T
0
239-332-9168. N
1 E 9
11 EXISTING PANEL TO REMAIN. M 3
3
12 REMOVE EXISTING PANEL IN DISPATCH AREA. EXTEND AND RECONNECT ALL BRANCH E S
A
CIRCUITS TO NEW PANEL "UPS-2A", PRIOR TO DEMOLITION. V N
O D
13 NEW PANEL. REFER TO RISER DIAGRAM FOR ADDITIONAL INFORMATION. RECESS PANEL O
IN EXISTING WALL, CUT AND PATCH AS REQUIRED TO CONCEAL ALL TOP/BOTTOM R TI RI
A
ENTERING CONDUIT. BRANCH CIRCUITS SERVING DISPATCH CONSOLE AREA SHALL P C E O
ROUTE DOWN INTO RAISED FLOOR SPACE. M NI NU FL
14 PROPOSED LOCATION OF TEMPORARY AUTOMATIC TRANSFER SWITCH, FOR SERVICE L I MU VE Y,
DURING CONSTRUCTION. PROVIDE FOR INSTALLATION OF SWITCH AND FLEXIBLE A M A T
2 CABLING FROM OUTDOOR GENERATOR TO EXISTING INDOOR MAIN MDP. SEE KEYNOTE 15 C O Z N
THIS SHEET AND DEMO RISER DIAGRAM FOR ADDITIONAL INFORMATION. C U
3 GENERATOR PAD UPS 1 11 E001 15 PROVIDE TEMPORARY SLEEVING THROUGH EXTERIOR WALL FOR ROUTING OF RI Y RTI CO
1 *20'-0" 13 UPS 2A UPS 2 12 16 TK#2EE/MY0 NPAOOWTRGEA RB14YA RTSEHE IRCSVO SIPCHPEEE ECRTA ,WB ALINREDES DCFEROMOUOMN T ROEIUSRTEPDROO IDSOIEAR,G 2TR RFAATM.N ,FS FRFOOERMR ASGDWEDNIITTECIROHAN TTAOOL R MIN PDFAPOD. R,S MMEAEINTIIMOUNM. LECT SAFET 665 O LEE
*NOTE: VERIFY PAD DIMENSIONS 18" BELOW GRADE. 5/8"x10' COPPER RODS AT EACH CORNER, EXOTHERMIC WELDED TO E
C 2 S,
WGEITNHE RCAUTMOMRIN SSH AOPPP DRROAVWEIDNGS. 4 1 CTOO UCNOTUENRTPEORIPSOE.I SPER WOVITIDHE # T2/E0S CTO WPEPLELR .AT ONE GROUND ROD. BOND GENERATOR GROUND ED BLI ER
21 17 #2/0 COPPER BURIED, BOND TO EXISITNG BUILDING COUNTERPOISE. TYPICAL (2) U Y
* LOCATIONS. EXOTHERMIC WELDS AT ALL CONNECTIONS. OS P M

1 18 TO SERVE COOLANT HEATER. 2-#10 & #10 GND. IN 1" C. TO EXISTING MDP. REFER TO NEW P T
RISER DIAGRAM. O R
O
MAIN BUILDING 2 4 19 TO SERVE BATTERY CHARGER. 2-#12 & #12 GND. IN 3/4" C. TO EXISTING PANEL "ME". R F
1 E101 REFER TO NEW RISER DIAGRAM. P
1 20 MOUNT GENERATOR EMERGENCY STOP SWITCH ON OUTSIDE OF ENCLOSURE.
26 E101 21 EXISTING INDOOR FCU AND OUTDOOR CU A/C UNITS, SERVING 911 DISPATCH IT RACK
ROOM. PROVIDE TEMPORARY COOLING TO THIS ROOM DURING ALL POWER OUTAGES.
21 (cid:57)(cid:17)(cid:42) APPROXIMATE CAPACITY EQUAL TO FIVE (5) TONS. TEMPORARY A/C UNIT WILL BE
POWERED BY PORTABLE GENERATOR, SEE NOTE 22.
22 PROVIDE TEMPORARY OUTDOOR PORTABLE DIESEL GENERATOR, WITH INTERNALLY
MOUNTED DISTRIBUTION PANEL, TO SERVE MICROWAVE, RADIO AND CEB BUILDINGS
CU-3 CU-2
DURING ALL POWER OUTAGES. REFER TO NOTES 21, 23, 24 AND 25 FOR LOAD
1 1 REQUIREMENTS. COORDINATE EXACT LOCATION OF TEMPORARY GENERATOR WITH LEE
COUNTY. INCLUDE ALL FLEXIBLE CABLING TO LOADS. ESTIMATED MINIMUM RATING 250
3
KW.
23
N
23 MICROWAVE BLDG. "A", PROVIDE TEMPORARY POWER PER KEYNOTE 22: TO PANEL A-1, G
480V, 2P-200A FEEDER. TO PANEL A-2, 480V, 2P-200A; TO ROOFTOP A/C UNIT #1, 480V, KI SI
E
3P-60A; TO ROOFTOP A/C UNIT #2, 480V, 3P-60A D 6
17 24 RADIO/MICROWAVE BLDG. "B", PROVIDE TEMPORARY POWER PER KEYNOTE 22: (1) 208V, WS N & 60
24 2P-125A FEEDER. O 2
E TI 01
25 CEB BUILDING, PROVIDE TEMPORARY POWER PER KEYNOTE 22: SERVICE A, (1) 480V, T C
4 14 15 2P-200A FEEDER. SERVICE B, (1) 480V, 2P-200A FEEDER. I C RU 0
17 26 PROVIDE FOR REMOVAL AND REPLACEMENT OF DOOR FRAME AT MAIN ENTRY AND SN E NST AR
4 GENERATOR PAD SECTION 10 OEQBSUTIPRMUECNTTIO TNHSR AOLUOGNHG B MUAILIND ICNOGR. CROIDNOTRR, AACST ROERQ SUHIRAELLD BTEO RAELSLPOOWN MSIOBVLEIN FGO NRE UWNLOADING WI T F CO NO.
6 AND COMPLETE INSTALLATION OF ALL NEW EQUIPMENT. I O
27 PROVIDE PROTECTION BOLLARD AROUND NEW GENERATOR, TYPICAL OF 6. 3'-6" HEIGHT H NT SE
ABOVE GRADE, 3'-0" EMBEDMENT DEPTH. FILL 4" STANDARD GI PIPE WITH CONCRETE. M. C ME EN
20 2 4 PROVIDE IN CONCRETE BASE TO 12" DEPTH AROUND PIPE. PAINT PIPE. R ART LIC
R A P
E A
E D D
22 1 T TY RI
16 N O
5 E OU L
19 1 C F
27 18 P E
4 E
L
1
1
8
9
4
7 25
CEB
rvt BUILDING
er.
s
u
a
h
k.
ar
m
_
4
1
R
_ 1
L
A
R
T
N
E
C
P
E
M
_
1
3 DATE ISSUED
0
14 FEBRUARY 02, 2015
7
s\ REVISIONS
nt
me 1 ADDENDUM 2 04/06/15
u SITE PLAN - ELECTRICAL
c
o 1
D
er\ 1" = 20'-0"
s
u
a
h
k.
ar SITE PLAN -
m
s\ ELECTRICAL
er
s
U
C:\ Brett L. Sands, P.E.
Florida License #48477
13099 S. Cleveland Ave.
M
P Suite 500
2 SHEET NUMBER
5 Fort Myers, Florida 33907
1:
3 Phone: [phone]
1:
5 Fax: [phone] E001
1 www.tlc-engineers.com
0
2 ©Copyright 2014TLC Engineering for Architecture, Inc.
6/
4/ EB #0000015 TLC NO: 714031 Seal
ELECTRICAL SPECIFICATIONS ELECTRICAL SYMBOL LEGEND GENERAL NOTES:
BASIC MATERIALS
DIVISION 16 - ELECTRICAL 3. SPOT PAINTING ON ROUGH-IN;
1. RECEPTACLES SHALL BE LOCATED 18 INCHES ABOVE FINISHED FLOOR TO CENTER LINE OF
71
DEVICE, UNLESS OTHERWISE NOTED. ABOVE COUNTER RECEPTACLES SHALL BE MOUNTED 6" 0
16010 BASIC ELECTRICAL REQUIREMENTS A. CONDUIT, RACEWAYS, BOXES, BACKBONES, PANELBOARDS, ETC. SHALL BE SPOT PAINTED. CONDUIT SHALL BE IDENTIFIED WITHIN 6 INCHES SYMBOL DESCRIPTION ABOVE BACK SPLASH TO CENTERLINE OF DEVICE. 0
OF THE BOX OR ENCLOSURE. THE ENTIRE BOX AND COVERPLATE SHALL BE PAINTED. R: 0
A. ALL WORK AND EQUIPMENT UNDER THIS DIVISION SHALL BE IN STRICT COMPLIANCE WITH THE CODES, STANDARDS AND PRACTICES LISTED HEREIN, AND THEIR RESPECTIVE DATES 2. EQUIPMENT SHALL BE OF MATERIALS SUITABLE FOR AND RATED FOR THE ENVIRONMENT IN BE 01.
B. USE FOLLOWING COLORS FOR COLOR BANDS AND FOR COLOR CODING; WHICH THEY ARE TO BE INSTALLED. 0
ARE FURNISHED AS THE MINIMUM LATEST REQUIREMENTS. T TRANSFORMER M

1. STATE OF FLORIDA. 1S)Y USPTSE MPOWER CBORILGOHRT ORANGE AUTOMATIC TRANSFER SWITCH A. 1W10O.RKING CLEARANCES FOR ELECTRICAL EQUIPMENT SHALL BE IN COMPLIANCE WITH NEC P NU 5 P1
2
2. LEE COUNTY. 2) NORMAL POWER WHITE A
R 4
3. CITY OF FORT MYERS. 3) MISCELLANEOUS COMMUNICATIONS BROWN 30AR NON-FUSED DISCONNECT SWITCH, SIZE AS NOTED B. THE EXCLUSIVELY DEDICATED SPACE EXTENDING FROM FLOOR TO STRUCTURAL CEILING T 4
4. LIFE SAFETY CODE - NFPA 101. NF NF DENOTES NON-FUSED WITH A WIDTH AND DEPTH OF THE PANELBOARD OR SWITCHBOARD MUST BE CLEAR OF ALL S 21
C. CABLE AND CONDUCTOR IDENTIFICATION WILL BE AS PER NFPA 70. PIPING, DUCTS, EQUIPMENT FOREIGN TO THE ELECTRICAL EQUIPMENT OR ARCHITECTURAL
5. UNDERWRITERS LABORATORIES, INC. PUBLICATIONS
30AR APPURTENANCES IN ACCORDANCE WITH NEC 408.
6. NATIONAL FIRE PROTECTION ASSOCIATION (NFPA). FUSED DISCONNECT
D. OPERATIONAL SIGNAGE SHALL BE PROVIDED WHERE REQUIRED. 20AF
7. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI). AR DENOTES AMP RATING OF SWITCH 3. WHEN ELECTRICAL BOXES ARE LOCATED IN VERTICAL FIRE-RESISTIVE ASSEMBLIES,
(CLASSIFIED AS FIRE/SMOKE AND SMOKE PARTITIONS), THEY SHALL BE INSTALLED WITHOUT
8. NATIONAL ELECTRICAL CODE - NFPA 70 (2008). 16110 BASIC MATERIALS AND METHODS AF DENOTES AMP FUSE SIZE AFFECTING THE FIRE CLASSIFICATION. ALL OF THE FOLLOWING CONDITIONS SHALL BE MET:
9. INSTITUTE OF ELECTRICAL AND ELECTRONIC ENGINEERS (IEEE).
10. NATIONAL ELECTRICAL MANUFACTURER'S ASSOCIATION (NEMA). A. RACEWAYS AND FITTINGS: SPD SURGE PROTECTION DEVICE A.ALL ELECTRICAL BOXES SHALL BE METALLIC. S 5
T
0
11. INTERNATIONAL POWER CABLE ENGINEER'S ASSOCIATION (IPCEA). BRANCH CIRCUIT PANELBOARD, UNDER 250 VOLTS, N
1. ALL WIRING SHALL BE INSTALLED IN APPROPRIATE RACEWAY SYSTEMS OF RIGID GALVANIZED CONDUIT, ELECTRIC METALLIC B.BOX OPENING SHALL OCCUR ONLY ON ONE SIDE OF FRAMING SPACE. E 9
12. NATIONAL ELECTRICAL SAFETY CODE (NBS HANDBOOK 81) SURFACE MOUNTED 3
TUBING, FLEXIBLE STEEL CONDUIT AND LIQUID-TIGHT FLEXIBLE CONDUIT AS CONDITIONS AND CODES DICTATE. EMT SHALL BE M
3
13. REQUIREMENTS OF LOCAL POWER CORPORATION. JOINED WITH STEEL COMPRESSION TYPE FITTINGS. C.BOX OPENING SHALL NOT EXCEED 16 SQUARE INCHES. E S
14. NATIONAL FIRE PROTECTION ASSOCIATION 72. BRANCH CIRCUIT PANELBOARD, UNDER 250 VOLTS, V N A
2. UNDERGROUND CONDUIT SHALL BE SCHEDULE 40 PVC. FLUSH MOUNTED D.ALL CLEARANCES BETWEEN OUTLET BOX AND GYPSUM BOARD SHALL BE COMPLETELY O O D
15. NATIONAL FIRE PROTECTION ASSOCIATION 99. FILLED WITH JOINT COMPOUND (OR OTHER APPROVED MATERIAL). R TI RI
16. BUILDING CODE: FLORIDA BUILDING CODE (2010). 3. ALL CONDUIT SHALL HAVE AN INSULATED COPPER EQUIPMENT GROUNDING CONDUCTOR THROUGHOUT THE ENTIRE LENGTH OF BRANCH CIRCUIT CONDUIT CONCEALED ABOVE P CA E O
1187.. NAIFAP GA U1I1D0E.LINES THE CIRCUIT WITHIN THE CONDUIT. PCHEAILSINEG, N OERU TINR WALA ALLN.D C GORNODUUNITD S CHOANLLD IUNCCTLOURDSE EO.FP TRHOEV WIDAEL AL RWAATLILN AGR SOHUANLDL BOEU TMLAEINTST ALIANREGDE.R THAN 16 SQUARE INCHES. THE INTEGRITY IM UNI ENU FL
16120 WIRES AND CABLES AS REQUIRED FOR CIRCUITS (UNLESS OTHERWISE NOTED). L M V Y,
F. THE TOTAL AGGREGATE SURFACE AREA OF THE BOXES SHALL NOT EXCEED 100 A M A T
TBR. SACNOSPPOE ROTFA WTIOORNK, :I N TSHUER AWNOCREK, TPERMOPVOIDREADR UYN PDREORT ETHCITSIO DNIV, ITSEIOMNP OSRHAARLLY ILNICGLHUTDINEG A, LSLU LPAEBROVRIS, IMOANT AENRDIA ILNSC, IPDEERNMTIATLS I,T INEMSPSE ECSTSIOENNTSI AALN DFO RRE IPNRSOPPEECRT IIONNS TFAELELSA,T TIOONO LASN, DE QOUPIEPRMAETNIOT,N, EVEN A. ALL BRANCH CIRCUITS SHALL BE COPPER WITH THHN OR THWN INSULATION. MINIMUM SIZE #12 AWG. GROUND OR GROUND ROD AS NOTED SQUARE INCHES PER 100 SQUARE FEET. C CO IZ UN
THOUGH NOT SPECIFICALLY MENTIONED OR INDICATED BUT WHICH ARE USUALLY PROVIDED OR ARE ESSENTIAL FOR PROPER INSTALLATION AND OPERATION OF ALL ELECTRICAL SYSTEMS B. FEEDERS AND SUBFEEDERS SIZE #4 AND LARGER SHALL BE XXHW COPPER. G.OUTLET BOXES LOCATED ON OPPOSITE SIDES OF FIRE RESISTIVE ASSEMBLIES SHALL RI Y RT O
C
AS INDICATED IN CONTRACT DOCUMENTS. C. COLOR CODING SHALL COMPLY WITH THE NATIONAL ELECTRIC CODE, 2008 EDITION SPECIFICALLY. PHASE CONDUCTORS OF EACH UP CONDUIT TURNING UP BE SEPARATED BY A MINIMUM HORIZONTAL DISTANCE OF 24 INCHES. CT ET O E
F 5
VOLTAGE SYSTEM MUST BE OF A DIFFERENT COLOR. NEUTRALS SHALL BE WHITE FOR 120/208. EQUIPMENT GROUNDING CONDUCTORS H.OUTLET BOXES SHALL BE SECURELY FASTENED TO WALL FRAMING MEMBERS. E A 6 E
C. NOTICES: GIVE ALL NOTICES, FILE ALL PLANS, PAY ALL FEES, OBTAIN ALL PERMITS AND APPROVALS FROM AUTHORITIES HAVING JURISDICTION. INCLUDE ALL FEES IN THE BID SHALL BE GREEN INSULATED. DN CONDUIT TURNING DOWN L S 6 L
PRICE. I. THE OPENING IN THE GYPSUM BOARD FACING SHALL BE CUT NOT TO EXCEED 1/8 INCH E C 2 S,
16130 OUTLET BOXES CONDUIT STUB BETWEEN THE EDGES OF THE OUTLET BOX AND THE EDGES OF THE OPENING. D LI R
B E
D. INTERPRETATION OF DRAWINGS: E
A. OUTLET BOXES: OUTLET BOXES SHALL BE ONE PIECE OR PROJECTION WELDED, GALVANIZED STAMPED STEEL FOR GANG SIZES REQUIRED. EXISTING TO BE REMOVED 4. ALL NEW AND EXISTING PANELS AFFECTED BY THIS PROJECT SHALL BE PROVIDED WITH A NEW S PU MY
SECTIONAL BOXES ARE NOT ACCEPTABLE. BOXES SHALL BE 4" SQUARE AND 1-1/2" DEEP GENERALLY. LARGER BOXES SHALL BE USED AS REQUIRED TYPE WRITTEN DIRECTORY. O
1. THE DRAWINGS ARE DIAGRAMMATIC AND ARE NOT INTENDED TO SHOW EXACT LOCATIONS OF CONDUIT RUNS, OUTLET BOXES, JUNCTION BOXES, PULL BOXES, ETC. THE
BY CODE. EXISTING TO REMAIN P T
LOCATIONS OF EQUIPMENT, APPLIANCES, FIXTURES, CONDUITS, OUTLETS, BOXES AND SIMILAR DEVICES SHOWN ON THE DRAWINGS ARE APPROXIMATE ONLY. EXACT LOCATIONS SHALL R
O
BE AS ACCEPTED BY THE ENGINEER DURING CONSTRUCTION. OBTAIN IN THE FIELD ALL INFORMATION RELEVANT TO THE PLACING OF ELECTRICAL WORK AND IN CASE OF 16231 ENGINE GENERATORS R O
F
INTERFERENCE WITH OTHER WORK, PROCEED AS DIRECTED BY THE ENGINEER AND PROVIDE ALL LABOR AND MATERIALS NECESSARY TO COMPLETE THE WORK IN AN ACCEPTABLE A. PROVIDE FOR COMPLETE INSTALLATION OF THE OWNER FURNISHED GENERATOR. P
MANNER.
B. PROVIDE FOR UNLOADING OF OWNER-FURNISHED EQUIPMENT AT SITE, WHEN SHIPPED DIRECTLY TO THE PROJECT SITE FROM
FACTORY/DISTRIBUTOR, WAREHOUSE.
2. DISCREPANCIES: NOTIFY OWNER/ENGINEER OF ANY DISCREPANCIES FOUND DURING CONSTRUCTION OF THE PROJECT AND DO NOT PROCEED WITH THAT PORTION OF THE C. ENGAGE FACTORY SERVICE REP FOR INSPECTION, ADJUSTMENTS, AND TESTING. NOTE: SOME SYMBOLS SHOWN ON THIS
1
PROJECT, UNTIL A WRITTEN DEFINITIVE STATEMENT IS RECEIVED PROVIDING CLEAR DIRECTION. IF A CONFLICT EXISTS BETWEEN THE CONTRACT DOCUMENTS AND ANY APPLICABLE D. REFER TO MANUFACTURER'S PRODUCT DATA PACKAGE FOR ADDITIONAL INFORMATION. LEGEND MAY NOT PERTAIN TO THIS PROJECT.
CODE OR STANDARD, THE MOST STRINGENT REQUIREMENT SHALL BE INCLUDED FOR THIS PROJECT. THE ENGINEER SHALL MAKE THE DECISION REGARDING QUESTIONABLE AREAS OF
16264 UNINTERRUPTIBLE POWER SUPPLY (UPS)
CONFLICT.
A. PROVIDE FOR COMPLETE INSTALLATION OF THE OWNER FURNISHED UPS. PHASING NOTES:
3. WIRING: EACH THREE-PHASE CIRCUIT SHALL BE RUN IN A SEPARATE CONDUIT UNLESS OTHERWISE SHOWN ON THE DRAWINGS. UNLESS OTHERWISE ACCEPTED BY THE B. PROVIDE FOR UNLOADING OF OWNER-FURNISHED EQUIPMENT AT SITE, WHEN SHIPPED DIRECTLY TO THE PROJECT SITE FROM
ENGINEER, CONDUIT SHALL NOT BE INSTALLED EXPOSED. WHERE CIRCUITS ARE SHOWN AS "HOME-RUNS" ALL NECESSARY FITTINGS FACTORY/DISTRIBUTOR, WAREHOUSE.
AND BOXES SHALL BE PROVIDED FOR A COMPLETE RACEWAY INSTALLATION. 1 C. ENGAGE FACTORY SERVICE REP FOR INSPECTION, ADJUSTMENTS, AND TESTING. 1. ALL WORK SHALL BE PERFORMED IN A REQUIRED SEQUENCE, TO MAINTAIN OPERATIONS WITHIN
D. REFER TO MANUFACTURER'S PRODUCT DATA PACKAGE FOR ADDITIONAL INFORMATION. THE EXISTING FACILITY. N
G
E. INVESTIGATION ON SITE: KI ESI
16425 SERVICE AND DISTRIBUTION 2. CONTRACTOR SHALL SUBMIT A SEQUENCE OF WORK TASKS, TO DEMONSTRATE THAT PHASING D 6
HAS BEEN CONSIDERED AND THAT THE PROPOSED SEQUENCE MEETS THE PROJECT S & 0
1. GENERAL: BEFORE COMMENCING THE WORK, VERIFY EXISTING CONDITIONS AT THE PREMISES INCLUDING, BUT NOT LIMITED TO, EXISTING STRUCTURAL FRAME, LOCATION AND A. SERVICE FROM TRANSFORMER TO MAIN SERVICE EQUIPMENT SHALL BE UNDERGROUND. REQUIREMENTS. SUBMIT PRIOR TO BEGINNING WORK. W N 6
O 2
AMACLELCC DOHIRAMDNEIINNCSGAIL OT ANONS TD; H EEEXL IIESNCTTTIENRNGITC O AOPLFE W TNHOINERG KCS,O EANQNTUDRI APCCMHTEA RNDATO CCTTYUEPMREEI,SN ATTNISCD.S E; XEAXMISITNIEN GA LWL AALDLJ AONINDI NPGA RWTOITRIOKN O LNO WCHATICIOHN TSH, ICSH WAORRAKC TISE RAINSYTWICASY A DNEDP REENLDAETNIOT,NSHIP TO EACH OTHER; EXISTING BFO. MRA MINE TSEERRIVNIGC ES HDAISLCLO BNEN IENCSTT ASLHLAELDL IHNA TVREA GNRSFOOURNMDE FRA USELTC OPRNODATRECYT CIOONM.P CAURRTRMEENNTT .TRANSFORMERS 3. REFER TO FLOOR PLANS AND RISER DIAGRAMS FOR ADDITIONAL REQUIREMENTS. 1 NIE CT TRUCTI R 001
16470 PANELBOARDS 4. LCIOSMT POLFE PTRE,O OPRO SINE DT HPER IPMRAORPYE TRA SSEKQSU AERNEC AES. CFOONLLTORWACST: OTHRI SS HLAISLTL IASD NDO TTO I NATNEDN MDEODD ITFOY BAES S E ONS A
2. POWER OUTAGE: SPECIAL ATTENTION IS CALLED TO THE FACT THAT WORK INVOLVED IS IN CONNECTION WITH EXISTING BUILDINGS WHICH OPERATE CONTINUOUSLY 24 HOURS PER DAY, AND WHICH REMAIN IN OPERATION REQUIRED TO MEET OWNER'S REQUIREMENTS: I T C O.
WHILE WORK IS BEING PERFORMED. WORK MUST BE DONE IN ACCORDANCE WITH THE DEFINED PHASING. SCHEDULE WORK FOR NO POWER OUTAGES TO OWNER CRITICAL SYSTEMS. REQUEST W I OF N
RWERQITUTIRENED P EART MOITSHSEIORN T AHNADN RSETCAENIDVAER WDR WITOTREKNI NAGC CHEOPUTRASN CWEH FERROEM O UTHTAEG OEWSN CEARN NNOO TL ABTEE ARC TCHEAPNT E7D2 HBYO UORWSN IENR A DDUVRAINNCGE R OEFG AULLLA PRO WWOERRK AINNGD HCOOUMRMSU. N PICRAOTTIEOCNT S EHXUISTT-DINOGW BNUSI.L DPIENRGFSO ARNMD WORK ATH. PEA TNHEELRSM SAHLA MLLA GBEN EFTUILCL T SYIZPEE,. M MINAIIMNSU MSH 2A0L" LW BIDEE L XU G5-S3 /O4"N DLYE EOPR U MSAINING BFRUELALK SEIZRES, ABSO LRTE-QOUNI RQEUDIC. KA-LML APKAEN, EQLUSI CTKO- BHRAEVAEK S CEIPRACRUAITT EB REQEAUKIPEMRESN OTF -- NTEEMWP UOPRSA R#2Y, UPAPNS E#L2S F AENEDD EFRESE.DERS. M. CH ENT NSE
EQUIPMENT DURING CONSTRUCTION. BG.R AOPUPNRDO VBEADR MANADN UTFYAPCETWURRITETRESN: DSQIRUEACRTEO RDI,E GSE., CUTLER HAMMER, SIEMENS. --- TTTEEEMMMPPPOOORRRAAARRRYYY GMA/EACNI NSE YSRSEATRTEOVMIRCS EA S NAEDNR DCV IOGNNEGNN 9EE1CR1TA DITOIOSNPRSA CTTOOCNH MN.IECCRTOIWONASV.E, RADIO, CEB BUILDINGS. R AR PARTM LICE
3. SPECIAL CONSIDERATIONS: SPECIAL ATTENTION IS CALLED TO THE FACT THAT THERE WILL BE PIPING, FIXTURES OR OTHER ITEMS IN THE EXISTING BUILDING WHICH MUST BE - DEMOLITION OF EXISTING MAIN UTILITY AND GENERATOR SERVICE. E DE DA
TRHEEM ONVEEWD C OORN SRTERLOUCCTAITOEND. IN ORDER TO PERFORM THE ALTERATION WORK. BID SHALL INCLUDE ALL REMOVAL AND RELOCATION REQUIRED FOR COMPLETION OF THE ALTERATIONS AND 16480 SAFETY SWITCHES AND ENCLOSED BREAKERS -- NREEWMO GVEEN TEERMAPTOORRA, TRRYA UNPSSF EFERE SDWEIRTSC.HES WITH MAIN SERVICE AND GENERATOR FEEDERS. T NTY ORI
- REMOVE TEMPORARY MAIN AND GENERATOR FEEDS. E OU L
A. ENCLOSED BREAKERS SHALL BE FULLY RATED, IN APPROPRIATE NEMA ENCLOSURE. C F
4. DEMOLITION - GENERAL: DURING THE EXECUTION OF WORK, ALL REQUIRED RELOCATION, REROUTING, ETC., OF EXISTING EQUIPMENT AND SYSTEMS IN THE EXISTING BUILDING P
E
AREAS WHERE THE WORK IS REQUIRED, SHALL BE PERFORMED BY THE CONTRACTOR, AS INDICATED ON THE DRAWINGS, OR AS REQUIRED BY JOB CONDITIONS AND AS DETERMINED B. ALL CONTROL, ALARM AND INTERLOCK WIRING SHALL BE IN CONDUIT AND SHALL BE COLOR CODED. 1 LE
BY THE OWNER IN THE FIELD, TO FACILITATE THE INSTALLATION OF THE NEW SYSTEMS. THE OWNER SHALL REQUIRE CONTINUOUS OPERATION OF THE EXISTING SYSTEMS, WHILE
DEMOLITION, RELOCATION WORK OR NEW TIE-INS ARE PERFORMED. C. DISCONNECT SWITCHES SHALL BE HEAVY DUTY AND SHALL USE A QUICK-MAKE, QUICK-BREAK
MECHANISM WITH AN ENCLOSURE OF A NEMA TYPE CONFORMING TO AREA IN WHICH IT IS INSTALLED.
DISCONNECTS FOR MOTORS SHALL BE HORSEPOWER RATED.
5. OWNER'S SALVAGE: THE OWNER RESERVES THE RIGHT TO INSPECT THE MATERIAL SCHEDULED FOR REMOVAL AND SALVAGE ANY ITEMS HE DEEMS USABLE AS SPARE PARTS.
D. APPROVED MANUFACTURERS: SQUARE D, GE, CUTLER HAMMER, SIEMENS.
F. EXISTING CONDITIONS:
16490 AUTOMATIC TRANSFER SWITCH
1. SUPPORT: ALL EXISTING CONDUIT AND CABLES WITHIN THE AREA OF RENOVATION SHALL BE PROVIDED WITH PROPER SUPPORTS AS SPECIFIED FOR NEW WORK IN OTHER
A. PROVIDE FOR INSTALLATION OF AUTOMATIC TRANSFER SWITCHES.
SECTIONS OF THIS SPECIFICATION.
B. PROVIDE FOR UNLOADING OF OWNER-FURNISHED EQUIPMENT AT SITE, WHEN SHIPPED DIRECTLY TO THE PROJECT SITE FROM
FACTORY/DISTRIBUTOR, WAREHOUSE.
2. INSTALLATION: ALL EXISTING ELECTRICAL WHICH IS DESIGNATED FOR REWORKING OR REQUIRES RELOCATION, REPAIR OR ADJUSTMENT SHALL CONFORM TO ALL APPLICABLE CODES
C. ENGAGE FACTORY SERVICE REP FOR INSPECTION, TESTING AND FINAL ADJUSTMENTS.
AND SHALL BE TREATED AS NEW WORK COMPLYING TO ALL SECTIONS OF THIS SPECIFICATION. 1
D. REFER TO MANUFACTURER'S PRODUCT DATA PACKAGE FOR ADDITIONAL INFORMATION.
3. VIOLATIONS: WHERE EXISTING CONDITIONS ARE DISCOVERED WHICH ARE NOT IN COMPLIANCE WITH THE CODES AND STANDARDS, THE CONTRACTOR SHALL SUBMIT PROPER 16709 SURGE SUPPRESSION , BONDING AND GROUNDING
DOCUMENTATION TO THE ARCHITECT FOR CLARIFICATION AND CORRECTIVE WORK DIRECTION. EXISTING CONDITIONS SHALL NOT REMAIN WHICH WILL CREATE A DISAPPROVAL OF THE
A. SURGE SUPPRESSION EQUIPMENT SHALL BE PROVIDED FOR ALL NEW DISTRIBUTION EQUIPMENT. IT SHALL BE INSTALLED ON THE MAIN
RENOVATED AREA. ELECTRICAL SERVICE, ALL DISTRIBUTION PANELS AND SELECTED SUB-PANELS, POWER SUPPLIES OF SPECIAL SYSTEMS, AND ON CIRCUITS
FEEDING SELECTED MAJOR ITEMS. A BONDING AND SINGLE POINT GROUNDING SYSTEM SHALL BE PROVIDED TO INTERCONNECT THE MAIN
4. PATCHING: ALL EXISTING CONDUIT AND CABLE PENETRATIONS SHALL BE PROPERLY FIRE TREATED PER CODE AND SPECIFICATION REQUIREMENTS. THE CONTRACTOR SHALL ELECTRIC SERVICE GROUND, LIGHTNING PROTECTION SYSTEM GROUNDS AND ALL SPECIAL ELECTRONIC SYSTEM ISOLATED GROUNDS.
MATCH EXISTING MANUFACTURER AND MODEL, BY TRANSTECTOR.
THOROUGHLY INSPECT ALL EXISTING LOCATIONS AND INCLUDE THE COST OF PATCHING AND REPAIR IN HIS PROPOSED CONSTRUCTION COST.
vt
ser.r G. ALL MATERIALS SHALL BE NEW, FREE FROM DEFECTS AND SHALL BE EITHER U.L. LABELED, U.L. LISTED OR BEAR THE SEAL OF A NATIONALLY RECOGNIZED ELECTRICAL TESTING BFA. CPTROORVYID/DEI SFTORRIB UUNTLOORA,D WINAGR EOHFO OUWSEN.ER-FURNISHED EQUIPMENT AT SITE, WHEN SHIPPED DIRECTLY TO THE PROJECT SITE FROM
u
ha LABORATORY.
k.
ar
m H. SHOP DRAWINGS ARE REQUIRED FOR ALL MATERIALS AND EQUIPMENT.
_
4
1
R I. ALL EQUIPMENT SHALL BE FIRMLY MOUNTED USING APPROVED HANGERS ATTACHED TO STRUCTURAL PORTIONS OF THE BUILDING. SUPPORTING WITH TIE WIRE IS PROHIBITED.
_
L
A
R
J. SERVICE AND METERING SHALL MEET THE REQUIREMENTS OF THE LOCAL UTILITY COMPANY FPL AND ALL PROVISIONS OF NFPA 70. COORDINATE ALL WORK AT SERVICE ENTRANCE, IN ADVANCE, WITH FPL.
T
N
E
C
K. SYSTEMS GUARANTEE: PROVIDE A ONE-YEAR GUARANTEE. THIS GUARANTEE SHALL BE BY THE CONTRACTOR TO THE OWNER FOR ANY DEFECTIVE WORKMANSHIP OR MATERIAL
P
E WHICH HAS BEEN PROVIDED UNDER THIS CONTRACT AT NO COST TO THE OWNER FOR A PERIOD OF ONE YEAR FROM THE DATE OF SUBSTANTIAL COMPLETION OF THE SYSTEM.
M
_ EXPLAIN THE PROVISIONS OF GUARANTEE TO THE OWNER AT THE "DEMONSTRATION OF COMPLETED SYSTEM".
1
3 DATE ISSUED
0
14 16020 TEST AND PERFORMANCE VERIFICATION FEBRUARY 02, 2015
7
s\ REVISIONS
nt A. EQUIPMENT AND APPLICATIONS SHALL BE PER NEMA STANDARDS.
me 1 ADDENDUM 2 04/06/15
u B. CABLES, MOTORS, GROUNDS, UNINTERRUPTIBLE POWER SUPPLY (UPS), AND THE EMERGENCY SYSTEM INCLUDING GENERATOR AND TRANSFER SWITCHES SHALL BE THOROUGHLY
oc TESTED. CONTRACTOR SHALL PROVIDE A REPORT INDICATING THE RESULTS OF ALL TESTS.
D
er\
s 16030 ELECTRICAL IDENTIFICATION
u
a
h
k. A. LANGUAGE ALL IDENTIFICATION SHALL BE IN ENGLISH.
ar LEGEND
m
B. PANELBOARDS, GENERATORS, TRANSFER SWITCHES, ENCLOSED BREAKERS AND ALL EQUIPMENT CABINETS WHICH ARE PART OF THE ELECTRICAL DISTRIBUTION SYSTEM SHALL BE
s\ AND
er PROVIDED WITH IDENTIFICATION MARKERS WHICH SHALL BE ENGRAVED PLASTIC, LAMINATE NAMEPLATES. CONDUIT SYSTEM MARKERS SHALL BE ADHESIVE OR PRE-TENSIONED SNAP ON
s COLOR CODED, SYSTEM MARKING MATERIALS.
U GENERAL
C:\ C. IDENTIFICATION: IDENTIFY ALL RACEWAYS PROVIDED OR UTILIZED AS PART OF THIS PROJECT AS FOLLOWS; Brett L. Sands, P.E. NOTES -
Florida License #48477
ELECTRICAL
1. APPLY BANDS 10 FEET ON CENTER ALONG THE RACEWAY SYSTEM AND AT EACH SIDE OF WALLS OR FLOORS, AND AT BRANCHES FROM MAINS.
2. IDENTIFY THE FOLLOWING SERVICES;
13099 S. Cleveland Ave.
M SERVICE LABEL
P Suite 500
3 A. LOW VOLTAGE 120/208 VOLTAGE SHEET NUMBER
5 Fort Myers, Florida 33907
1: B. ALARM MONITORING ALARM
3 Phone: [phone]
1: C. EMERGENCY EMERGENCY
5 Fax: [phone] E000
1 www.tlc-engineers.com
0
2 ©Copyright 2014TLC Engineering for Architecture, Inc.
6/
4/ EB #0000015 TLC NO: 714031 Seal