Remington 597 Takedown Guide

7 Pages·2005·2.912 MB·English

Remington 597
TakedoftnG uide
MADE EASY
Clean your own gun with confidence.
Savesy ou moneyo n repairs!
Remington5 97
T"
ndz
'@
2 Trieea Hosing A$onbly
3 Bml Asanbly
4 Dolr
5 Boh Guide Rd (2)
6 cuid. Rnit sffi (2)
TAclion sFin$ (2)
3 M,guin€ BoxA$onbly
9 As€dlHy PiD WAR]T{ING:
l0 Boh Buff€r
Triegd Hosing Asanbt Make suret he gun is
13 Hold OFn Pit entirely unloadedb efore
14ltoldO p€n 5 sFins Bshins (2)
15 Eold Op6 SFirB startingt he disassembly;
l7 Firing Pin Spring visually checks omer ounds
l8 Fidig Pio Raaining Ptr
19 Ext6.tor Sprhg canh ide.
20 Extrror lluga 1l Eold OpenS p.ing
22 Bml Cldp
23 Bdd CldO Smw Reade veryi nstruction
24 R*ivd llug Sc@ 15 Rd*e Rebining Pin
25 Bolt Hmdle carefully using the picture
26 Frcnl SiBl* Scfl l? SaGtt SpnnaR et iritrg Pin
2? Fmnt Sight only as a reference.
28 Rd Sietu B6e Sc@ (2)
29 Ra Signr Bdc 20 Safctj' Detcnt llued
Copyright@ 2 005b y JC RadocyC o. www.takedownguides.com
1. Push the magaziner eleaset o the rear and remove
magazine
t'--2.
Ilnscrew the two takedown screwst o releaset he barrel/
action and trigger guard assemblyf rom the stock.
3. The plasticinserts from the takedown screwsc an fall out of the fi
.,ffi'^
stock. Remove them so thev do not becomel ost.
4. Drift out the assemblyp in (right to left) and pull the trigger guard assemblyd own out
of the receiver.
5. Pull the bolt handlef rom the bolt
6. Unscrew the guide rail retaining screws
from the rear of the receiver.
7. Slide the action springs forward and grab the
bolt guide rail with needlen osedp liers and push
it out toward the rear. Either way restrain the
action springsa s the guide rail is removed.
Removet he guide rails and springsa nd mark
them left/risht.
8. Removet he bolt from the receiver.
9. Utrscrew the barrel clamp screw.
L0. fry the barrelc lampo ut.
the barrel out of the receiver as shown.
11. Remove the barrel from the receiver.
Do not disassemblet he bolt handle spring it is riveted in place.
12. Use a small tool to pry betweent he extractor and its
'*plunger.
With the plunger and spring pushed back lift the
, extractor out of the bolt. Remove the plunger and spring.
FE
L"**-;-{
,^,,,,,rr
tr
L3.
Drift the firing pin retaining pin left to right F
and remove the firing pin and its spring.
14. Drift out the ejector pin and remove the ejector from the
trigger guard assembly.
g
s
15. fry at the hold openp in to releaseth e hold opena nd
its spring.
For Reassembly: Note were the spring rests on thefront
of the trigger guard.
16. Place the hammer in the fired position. Drift out the hammer pivot pin and remove
the hammer and its spring. There are black plastic inserts on the spring were the pivot pin
goest hrough do not lose them as you remove the hammer and spring. For reassemblya
slave pin is very helpful. You can easily damage thosep lastic inserts, be very gently with
disassembly as weII as reassembly.
17. Drift out all threep ins shown.
18. Trigger/searp arts shown. This looks like it might be diffr-
cult to reassemble,h ave patience and be sure the pin in the
middle doesn't deform the spring when it goes back through the
loop.
L9. nrift the safetyr oll pin out from right to left.
in the safety spring as you drift out the roll
in. Remove the spring and its plunger and then
ll the safety out of the guard.
Not Recommended: The magaziner eleases hould not be disas-
sembled.