Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering 2003: Vol 217 Index PDF
Preview Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering 2003: Vol 217 Index
Author Index Abdul Ghani, A. G. A computational and experimental study of heating and cooling cycles during thermal sterilization of liquid foods in pouches using CFD Abou-Chakra, H. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Abou-Chakra, H. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257 266 tester Aleem, H. Pharmaceutical process validation: an overview 14] 15) Aleem, H. Reinterpreting validation 287 293 Asako, Y. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles 279 286 Banim, R. S. Application of inverse methods to temperature measurement in internal mixers 295 306 Bankes, A. Development of a piezoelectric force sensor for a chip refiner 133 140 Bansal, P. K. Feasibility of air cycle systems for low-temperature refrigeration applications with heat recovery 267 274 Barton, D. C. Coupled thermomechanical simulation of the polymer die drawing process 123 132 Berry, R. J. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Bohan, M. F. J. Film thickness prediction in halftone screen printing 345 359 Bradley, M. S. A. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Bradley, M. S. A. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257 266 tester Brett, P. N. Application of inverse methods to temperature measurement in internal mixers 295 306 Bridle, I. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Bridle, I. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257 266 tester Cammarata, L. Designing an optimal controller for rectangular natural circulation loops 171 180 Chen, X. D. A computational and experimental study of heating and cooling cycles during thermal sterilization 1-9 of liquid foods in pouches using CFD Claypole, T. C. An experimental investigation into ink transfer using a roller squeegee in high-speed screen printing 307 321 Claypole, T. C. Film thickness prediction in halftone screen printing 345 359 Crawford, N. M. Prediction of pressure drop for turbulent fluid flow in 90° bends 153 156 Cunningham, G. Prediction of pressure drop for turbulent fluid flow in 90° bends 153 156 Davies, C. E. An acoustic method for in-line particle size measurement in flowing bulk solids 33-40 Epstein, N. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles 279 286 Falope, G. B. O. Modelling ductile failure propagation during blowdown under localized jet fire attack 93-102 Farid, M. M. A computational and experimental study of heating and cooling cycles during thermal sterilization 1-9 of liquid foods in pouches using CFD Fichera, A. Designing an optimal controller for rectangular natural circulation loops 171 Fox, I. J. An experimental investigation into ink transfer using a roller squeegee in high-speed screen printing 307-: Fox, I. J. Film thickness prediction in halftone screen printing 345-35 Gethin, D. T. An experimental investigation into ink transfer using a roller squeegee in high-speed screen printing 307 Gethin, D. T. Film thickness prediction in halftone screen printing 345 Grace, J. R. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles Hammoud, A. H. Performance of a rotating drum skimmer in oil spill recovery Harkin-Jones, E. M. A. Plug force monitoring for the control and optimization of the thermoforming process Harron, G. W. Plug force monitoring for the control and optimization of the thermoforming process Hasan, M. M. Skewed velocity profile effect on turbine flowmeter performance Hinds, M. Application of inverse methods to temperature measurement in internal mixers Islam, M. M. Skewed velocity profile effect on turbine flowmeter performance Jewell, E. H. An experimental investigation into ink transfer using a roller squeegee in high-speed screen printing Khalil, M. F. Performance of a rotating drum skimmer in oil spill recovery Kirkegaard, M. An acoustic method for in-line particle size measurement in flowing bulk solids Kovacevic, A. Opportunities for innovation with screw compressors 157- 170 Leaper, M. C. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Leaper, M. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257- 266 tester Lee, D. H. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles 279-286 Leon, F. Thermomechanical analysis of a piercing mandrel for the production of seamless steel tubes 337-344 Li, F. Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester 233-242 Lord, S. Pharmaceutical process validation: an overview 141- 151 © IMechE 2003 Proc. Instn Mech. Engrs Vol. 217 Part E: J. Process Mechanical Engineering 362 AUTHOR INDEX Lord, S. V. Reinterpreting validation 287-293 Mahgerefteh, H. Modelling ductile failure propagation during blowdown under localized jet fire attack 93-102 Marono, R. Thermomechanical analysis of a piercing mandrel for the production of seamless steel tubes 337-344 Martin, P. J. Plug force monitoring for the control and optimization of the thermoforming process 181-188 Mba, D. Mechanical evolution of the rotating biological contactor into the 21st century 189-220 McCarthy, T. Pharmaceutical process validation: an overview 141-151 McCarthy, T. J. Reinterpreting validation 287-293 Mirza, M. S. Coupled thermomechanical simulation of the polymer die drawing process 123-132 Nagahashi, Y. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles 279-286 Novozhilov, V. Some aspects of the mathematical modelling of fireballs 103-122 Ouellet, D. Development of a piezoelectric force sensor for a chip refiner 133-140 Pagano, A. Designing an optimal controller for rectangular natural circulation loops 171-180 Parkinson, H. J. Analysis and taxonomy of remanufacturing industry practice 243-256 Prince, J. C. Thermomechanical analysis of a piercing mandrel for the production of seamless steel tubes 337-344 Puri, V. M. Mechanical behaviour of powders using a medium pressure flexible boundary cubical triaxial tester 233-242 Reed, A. R. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Reed, A. R. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257-266 tester Senger, J. Development of a piezoelectric force sensor for a chip refiner 133-140 Seshadri, V. Skewed velocity profile effect on turbine flowmeter performance 25-32 Sharratt, P. M. Pharmaceutical process validation: an overview 141-151 Sharratt, P. N. Reinterpreting validation 287-293 Siadat, A. Development of a piezoelectric force sensor for a chip refiner 133-140 Sii, H. S. A design-decision support framework for evaluation of design options/proposals using a composite 59-76 structure methodology based on the approximate reasoning approach and the evidential reasoning method Singh, S. N. Skewed velocity profile effect on turbine flowmeter performance 25-32 Smitj, I. K. Opportunities for innovation with screw compressors 157-170 Spedding, P. L. Prediction of pressure drop for turbulent fluid flow in 90° bends 153-156 Spengler, J. D. Air quality in aircraft 323-335 Stevenson, D. G. A review of current and developing potable water treatment processes 11-23 Stosic, N. M. Opportunities for innovation with screw compressors 157-170 Tallon, S. An acoustic method for in-line particle size measurement in flowing bulk solids 33-40 Tan, D. M. Fire-induced failure of a propane tank: some lessons to be learned 79-92 Taraiya, A. K. Coupled thermomechanical simulation of the polymer die drawing process 123-132 Thompson, G. Analysis and taxonomy of remanufacturing industry practice 243-256 Tierney, M. J. Application of inverse methods to temperature measurement in internal mixers 295-306 Tuziin, U. An investigation of particle degradation by impact within a centrifugal accelerator type degradation 257-266 tester Tiiziin, U. Measuring the tensile strength of caked sugar produced from humidity cycling 41-47 Venart, J. E. S. Fire-induced failure of a propane tank: some lessons to be learned 79-92 Wang, J. A design-decision support framework for evaluation of design options/proposals using a composite 59-76 structure methodology based on the approximate reasoning approach and the evidential reasoning method Ward, I. M. Coupled thermomechanical simulation of the polymer die drawing process 123-132 Wild, P. M. Development of a piezoelectric force sensor for a chip refiner 133-140 Williamson, N. J. Feasibility of air cycle systems for low-temperature refrigeration applications with heat recovery 267-274 Wilson, D. G. Air quality in aircraft 323-335 Xu, J. Fire-induced failure of a propane tank: some lessons to be learned 79-92 Yedidiah, S. An overview of methods for calculating the head of a rotodynamic impeller and their practical 221-232 significance Yokogawa, A. Effect of liquid addition on heat transfer in gas-fluidized beds of large light particles 279-286 Zhao, Y. Pharmaceutical process validation: an overview 141-151 Zhao, Y. Reinterpreting validation 287-293 Proc. Instn Mech. Engrs Vol. 217 Part E: J. Process Mechanical Engineering ) IMechE 2003
The list of books you might like
