Pro Industrial Pro-Cryl® Universal Acrylic Primer Red Oxide 2 Coats

28 Pages·2016·0.48 MB·English

SCHEDULE
Exterior Finishes
Aluminum
Primer: B66N00310 - Pro Industrial Pro-Cryl® Universal Acrylic Primer Red Oxide
Follow product data pages for proper prep and application.
2 Coats: B65B00720 - Pro Industrial Waterbased Acrolon 100 Polyurethane (Part A) Black
Follow product data pages for proper prep and application.
1-2 coats as needed to achieve proper film build
END OF SECTION
SURFACE PREPARATION
1) Aluminum
Remove all oil, grease, dirt, oxide and other foreign material by cleaning per SSPC-SP1, Solvent
Cleaning.
2) Galvanized Metal
Allow to weather a minimum of 6 months prior to coating. Clean per SSPC-SP1 using detergent and
water or a degreasing cleaner, then prime as required. When weathering is not possible or the surface
has been treated with chromate's or silicates, first Solvent Clean per SSPC-SP1 and apply a test
area, priming as required. Allow the coating to dry at least one week before testing. If adhesion is
poor, Brush Blast per SSPC-SP7 is necessary to remove these treatments.
3) Previously Coated Surfaces
Maintenance painting will frequently not permit or require complete removal of all old coatings prior to
repainting. However, all surface contamination such as oil, grease, loose paint, mill scale, dirt, foreign
matter, rust, mold, mildew, mortar, efflorescence, and sealers must be removed to assure sound
bonding to the tightly adhering old paint. Glossy surfaces of old paint films must be clean and dull
before repainting. Thorough washing with an abrasive cleanser will clean and dull in one operation, or,
wash thoroughly and dull by sanding. Spot prime any bare areas with an appropriate primer.
Recognize that any surface preparation short of total removal of the old coating may compromise the
service length of the system. Check for compatibility by applying a test patch of the recommended
coating system, covering at least 2 to 3 square feet. Allow to dry one week before testing adhesion
per ASTM D3359. If the coating system is incompatible, complete removal is required.
4) Solvent Cleaning
Solvent Cleaning is a method for removing all visible oil, grease, soil, drawing and cutting compounds,
and other soluble contaminants. Solvent cleaning does not remove rust or mill scale. Change rags
and cleaning solution frequently so that deposits of oil and grease are not spread over additional
areas in the cleaning process. Be sure to allow adequate ventilation. For complete instructions, refer
to Steel Structures Paint Council Surface Preparation Specification No. 1. (SSPC-SP1)
5) Hand Tool Cleaning
Hand Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is
not intended that adherent mill scale, rust, and paint be removed by this process. Mill scale, rust, and
paint are considered adherent if they cannot be removed by lifting with a dull putty knife. Before hand
tool cleaning, remove visible oil, grease, soluble residues, and salts by the methods outlined in SSPC-
SP1. For complete instructions, refer to Steel Structures Paint Council Surface Preparation
Specification No. 2 (SSPC-SP2)
6) Power Tool Cleaning
Power Tool Cleaning removes all loose mill scale, loose rust, and other detrimental foreign matter. It is
not intended that adherent mill scale, rust, and paint be removed by this process. Mill scale, rust, and
paint are considered adherent if they cannot be removed by lifting with a dull putty knife. Before power
tool cleaning, remove visible oil, grease, soluble residues, and salts by the methods outlined in SSPC-
SP1. For complete instructions, refer to Steel Structures Paint Council Surface Preparation
Specification No.3.(SSP-PC3)
END OF SPECIFICATION
Data Pages
113.05
PRO
PRO-CRYL®
UNIVERSAL PRIMER
INDUSTRIAL™

B66W00310 OFF WHITE
As of 09/11/2015, Complies with: B66A00310 GRAY
OTC Yes LEED® 09 CI Yes
SCAQMD Yes LEED® 09 NC Yes B66N00310 RED OXIDE
CARB Yes LEED® 09 CS Yes
CARB SCM 2007 Yes LEED® 09 S Yes
MPI 107,134 NGBS Yes
CHARACTERISTICS RECOMMENDED SYSTEMS

Waterborne topcoat:
Pro Industrial Pro-Cryl Universal
1-2 cts. Pro Industrial Acrylic
Primer is an advanced technology, self
or Pro Industrial DTM Acrlyic
cross-linking acrylic primer. It is rust
or Pro Industrial Multi-Surface Acrylic
inhibitive and designed for commercial,
or Pro Industrial Pre-Catalyzed Waterbased Epoxy
new construction and maintenance
or Pro Industrial Waterbased Acrolon 100
applications. It can be used as a primer
or Pro Industrial Waterbased Catalyzed Epoxy
under water-based or solvent-based high

performance topcoats.

 Rust inhibitive
Solventborne topcoat:
 Single component
1-2 cts. Pro Industrial High Performance Epoxy
 Early moisture resistant
or Pro Industrial Urethane Alkyd
 Fast dry

 Low temperature application 40°F
 Interior and exterior use
 Suitable for use in USDA inspected
facilities
Pro Industrial Pro-Cryl Universal Primer B66W310 Off White is GREENGUARD GOLD certified for low
Color: Off White, Gray, Red Oxide chemical emissions into indoor air during product usage. For more information, visit ul.com/gg.
Recommended Spread Rate per coat:
Wet mils: 5.0 - 10.0 System Tested: (unless otherwise indicated)
Dry mils: 1.8 - 3.6 Substrate: Steel
~Coverage: 160 - 320 sq ft/gal Surface Preparation: SSPC-SP10
Approximate 1 ct. Pro Industrial Pro-Cryl Universal Primer
Theoretical coverage sq ft/gal 1 ct. Pro Industrial Acrylic
(m2/L) @ 1 mil / 25 microns dft 577sq ft
Adhesion: Moisture Condensation Resistance:
NOTE: Brush or roll application may require multiple
coats to achieve maximum film thickness and Method: ASTM D4541 Method: ASTM D4585, 100°F, 1250
uniformity of appearance. Result: 500 psi hours
Result: Passes
Drying Time @ 6.0 mils wet 50% RH: Corrosion Weathering:
40°F 77°F 120°F Method: ASTM D5894, 10 cycles, Pencil Hardness:
To touch: 2 hrs 40 min 20 min 3360 hours Method: ASTM D3363
Tack free: 8 hrs 2 hrs 1 hr Result: Passes Result: H
To recoat: 16 hrs 4 hrs 2 hrs
To cure: 45 days 30 days 14 days Direct Impact Resistance: Salt Fog Resistance:
Drying time is temperature, humidity, and film Method: ASTM D2794 Method: ASTM B117, 1250 hours
thickness dependent.
Result: >140 in. lbs. Result: Passes
Finish: Low sheen

Flash Point: N/A
Dry Heat Resistance*: Provides performance comparable to
Shelf Life: 36 months, unopened
Method: ASTM D2485 products formulated In Lieu of Federal
Store indoors at 40°F to 100°F.
Result: 200°F Specification: AA50557 and Paint
Tinting: Do not tint
Specification: SSPC-Paint 23.
B66W310 (may vary by color)
Flexibility:
VOC (less exempt solvents):
Method: ASTM D522, 180° bend,
96 g/L; 0.80 lb/gal
1/4" mandrel
As per 40 CFR 59.406 and SOR/2009-264, s.12
Volume Solids: 36% ± 2% Result: Passes
Weight Solids: 49% ± 2%
Weight per Gallon: 10.23 lb
*Suitable for intermittent dry heat resistance up to 300°F when used as a system with Sher-Cryl HPA
9/2015 www.sherwin-williams.com continued on back
PRO INDUSTRIAL™
PRO-CRYL® UNIVERSAL PRIMER
SURFACE PREPARATION APPLICATION

WARNING! Removal of old paint by sanding, scraping or other means may generate Refer to the SDS before using
dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain Temperature: 40°F minimum
damage or other adverse health effects, especially in children or pregnant women. 120°F maximum
Controlling exposure to lead or other hazardous substances requires the use of (air, surface, and material)
proper protective equipment, such as a properly fitted respirator (NIOSH approved) At least 5°F above dew point
and proper containment and cleanup. For more information, call the National Lead Relative humidity: 85% maximum
Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
The following is a guide. Changes in pressures and
Do not use hydrocarbon solvents for cleaning. tip sizes may be needed for proper spray
characteristics. Always purge spray equipment before

use with listed reducer. Any reduction must be
Iron & Steel - Minimum surface preparation is Hand Tool Cleaning per SSPC-SP2. compatible with the existing environmental and
Remove all oil and grease from the surface per SSPC-SP1. For better performance, application conditions.

use Commercial Blast Cleaning per SSPC-SP6.
Reducer: Water

Aluminum - Remove all oil, grease, dirt, oxide and other foreign material per SSPC-
Airless Spray
SP1.Prime the area the same day as cleaned.
Pressure .................................... 2000 psi

Hose ............................................ 1/4" ID
Galvanizing - Allow to weather a minimum of six months prior to coating. Solvent
Tip ...................................... .015" - .019"
Clean per SSPC-SP1. When weathering is not possible, or the surface has been
Filter ......................................... 60 mesh
treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a
Reduction .................. Not recommended
test patch. Allow paint to dry at least one week before testing adhesion. If adhesion is

poor, brush blasting per SSPC-SP7 is necessary to remove these treatments. Rusty
Conventional Spray
galvanizing requires a minimum of Hand Tool Cleaning per SSPC-SP2, prime the
Gun .......................................... Binks 95
area the same day as cleaned.
Fluid Nozzle ........................................ 66

Air Nozzle ...................................... 63PB
Previously Painted Surfaces - If in sound condition, clean the surface of all foreign
Atomization Pressure .................... 60 psi
material. Smooth, hard or glossy coatings and surfaces should be dulled by abrading
Fluid Pressure ...............................2 5 psi
the surface. Apply a test area, allowing paint to dry one week before testing
ReductionAs needed up to 5% by volume
adhesion. If adhesion is poor, additional abrasion of the surface and/or removal of

the previous coating may be necessary. Retest surface for adhesion. If paint is
Brush ........................... Nylon/Polyester
peeling or badly weathered, clean surface to sound substrate and treat as a new
Reduction .................. Not recommended
surface as above. Recognize that any surface preparation short of total removal of

the old coating may compromise the service length of the system.
Roller ...................................3/8" woven

APPLICATION PROCEDURES ReductionAs needed up to 5% by volume

Apply paint at the recommended film thickness and spreading rate as indicated on
If specific application equipment is listed above,
front page. Application of coating below minimum recommended spreading rate will equivalent equipment may be substituted.
adversely affect coating performance.
CLEANUP INFORMATION
SAFETY PRECAUTIONS
Refer to the SDS sheets before use. FOR PROFESSIONAL USE ONLY Clean spills and spatters immediately with
Published technical data and instructions are subject to change without notice. soap and warm water. Clean hands and tools
Contact your Sherwin-Williams representative for additional technical data and immediately after use with soap and warm
water. After cleaning, flush spray equipment
instructions.
with compliant cleanup solvent to prevent

rusting of the equipment. Follow
PERFORMANCE TIPS manufacturer's safety recommendations when
No painting should be done immediately after a rain or during foggy weather. using solvents.
When using spray application, use a 50% overlap with each pass of the gun to avoid
holidays, bare areas, and pinholes. Apply coating evenly while maintaining a wet HOTW 09/11/2015 B66W00310 32 96

edge to prevent lapping.
KOR, FRC, SP

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such
information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams
representative or visit www.paintdocs.com to obtain the most current version of the PDS and/or an SDS.
113.68
PRO

WATERBASED ACROLON™100
WATERBASED URETHANE
INDUSTRIAL™
Part A B65W00721 Extra White Base
Part A B65T00724 Ultradeep/Clear Base
Part A B65B00720 Black
As of 10/09/2015, Complies with: Part A B65R00720 Safety Red
OTC Yes LEED® 09 CI Yes Part A B65Y00720 Safety Yellow
SCAQMD Yes LEED® 09 NC Yes
CARB Yes LEED® 09 CS Yes Part B B65V00720 Hardener
CARB SCM 2007 Yes CalGreen 2013 Yes
MPI NGBS Yes
CHARACTERISTICS RECOMMENDED SYSTEMS

Steel:
Pro Industrial Water Based Acrolon 100
1 ct.Pro Industrial Pro-Cryl Primer Concrete: (high performance)
is an advanced technology, <100 g/L VOC,
1-2cts.Pro Industrial Water Based Acrolon 100 1 ct.Kem Cati-Coat HS Epoxy Filler/Sealer
waterbased, acrylic urethane. It provides
performance properties comparable to Steel: 1-2cts.Pro Industrial Water Based Acrolon 100
premium quality solvent based urethanes. 1 ct.Zinc-Clad IV Primer Concrete/Masonry:
This is a high gloss, abrasion resistant 1-2cts.Pro Industrial Water Based Acrolon 100 1 ct.Loxon Concrete & Masonry Primer
urethane that has excellent weathering Steel: 1-2cts.Pro Industrial Water Based Acrolon 100
properties. 1 ct.Zinc-Clad IV Primer Drywall:
 Can be applied directly to water based 1 ct.Macropoxy 646-100 1 ct.ProMar 200 Zero VOC Primer
and solvent based organic zinc rich 1-2cts.Pro Industrial Water Based Acrolon 100 1-2cts.Pro Industrial Water Based Acrolon 100
primers
Aluminum: Galvanizing:
 Suitable for use in USDA inspected
1 ct.DTM Wash Primer 1 ct.DTM Wash Primer
facilities
1-2cts.Pro Industrial Water Based Acrolon 100 1-2cts.Pro Industrial Water Based Acrolon 100
 Acceptable for use in high performance
Concrete Block (CMU): Pre-Finished Siding:(Baked-on finishes)
architectural applications
1 ct.Heavy Duty Blockfiller 1 ct.Bond-Plex WB Acrylic
Color: many colors
1-2cts.Pro Industrial Water Based Acrolon 100 1-2cts.Pro Industrial Water Based Acrolon 100
Recommended Spread Rate per coat:
Wet mils: 4.0 - 8.0
Dry mils: 1.8 - 3.6 The systems listed above are representative of the product's use, other systems may be appropriate.
Coverage: 200 - 400 sq ft/gal
System Tested: (*unless otherwise indicated below)
Approximate spreading rates are calculated on volume solids
and do not include any application loss. Note: Brush or roll Substrate: Steel
application may require multiple coats to achieve maximum Surface Preparation*: SSPC-SP10
film thickness and uniformity of appearance.
Drying Time @ 5.0 mils wet 50% RH:
@ 55°F @ 77°F @ 120°F 1 ct. Waterbased Tile-Clad Primer @ 4.0 mils (100 microns) dft
To touch: 3 hr 1.5 hr 45 min 1 ct. Pro Industrial Waterbased Acrolon 100 @ 3.0 mils (75 microns) dft
To handle: 12 hrs 6 hrs 2 hrs
To recoat: Adhesion: Salt Fog Resistance: System Tested
minimum: 16 hrs 8 hrs 2-4 hrs Method: ASTM D4541 (Zinc Clad IV, 2 coats Water Based Acrolon 100)
maximum: 3 months Result: 1080 psi Method: ASTM B117, 4000 hours
To Cure: 14 Days 10 Days 2 days Corrosion Weathering: Rating 9 per ASTM D610 for
Pot Life: 2.5 hrs 2 hrs 45 min Method: ASTM D5894, 10 cycles rusting
Sweat-in-Time: None 3360 hours, Scrub Resistance:
Drying time is temperature, humidity, and film thickness
dependent. Result: Rating 10, per ASTM D610 Method: ASTM D2486, 5000+ cycles,
Finish: 80+@ 60° High Gloss for rusting, no more than with no visible wear
Flash Point: 105°F TCC catalyzed 1/8” rust creepage at scribe Accelerated Weathering - QUV:
Shelf Life: 24 months, unopened Direct Impact Resistance: Method: ASTM D4587, QUV-A,
Store indoors at 40°F to 100°F. Method: ASTM D2794 2000 hours
Tinting part A with CCE or Envirotoner: Result: >160 in. lb Result: Passes
Use the 100% tint strength formula pages. Five Flexibility:
minutes minimum mixing on a mechanical shaker is Method: ASTM D522, 180° bend,
required for complete mixing of color.
1/8" mandrel

Extra White B65W00721/B65V00720 Result: Pass
VOC (less exempt solvents): Mixed/Unreduced: Pencil Hardness:
97 g/L - 0.81 lb/gal Method: ASTM D3363
As per 40 CFR 59.406 and SOR/2009-264, s.12 Result: 3H
Mix Ratio: 4:1 by volume

Volume Solids: 45 ± 2%
Weight Solids: 52 ± 2%
Weight per Gallon: 9.54 lb
10/2015 www.sherwin-williams.com continued on back
PRO INDUSTRIAL
WATER BASED ACROLON 100
APPLICATION
SURFACE PREPARATION
Temperature: 55°F(13°C) minimum
WARNING! Removal of old paint by sanding, scraping or other means may generate dust or
120°F (49°C) maximum
fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other
(Air, surface, and material)
adverse health effects, especially in children or pregnant women. Controlling exposure to lead
At least 5°F (2.8°C) above dew point
or other hazardous substances requires the use of proper protective equipment, such as a
Relative humidity: 85% maximum
properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more

information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact
The following is a guide. Changes in pressures
your local health authority.
and tip sizes may be needed for proper spray

characteristics. Always purge spray equipment
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust,
before use with listed reducer. Any reduction
and other foreign material to ensure adequate adhesion.
must be compatible with the existing
Do not use hydrocarbon solvents for cleaning.
environmental and application conditions.

Reduction over 15% of material can affect film
Iron & Steel - Remove all oil and grease from surface by Solvent Cleaning per SSPC-SP1.
build, appearance, and adhesion.
Minimum surface preparation is Commercial Blast Cleaning per SSPC-SP6/NACE 3. For better
When using spray application, use a 50%
performance, use Near White Blast Cleaning per SSPC-SP10/NACE 2. Blast clean all surfaces
overlap with each pass of the gun to avoid
using a sharp, angular abrasive for optimum surface profile (2 mils / 50 microns). Prime any
holidays, bare areas, and pinholes. If
bare steel the same day as it is cleaned or before flash rusting occurs.
necessary, cross spray at a right angle.

Aluminum - Remove all oil, grease, dirt, oxide and other foreign material per SSPC-SP1.
Clear Tint Base (B65T00724) can be used as
Primer required.
clear coat

Galvanizing - Allow to weather a minimum of six months prior to coating. Solvent Clean per
Reducer: Water
SSPC-SP1. When weathering is not possible, or the surface has been treated with chromates or
Airless Spray
silicates, first Solvent Clean per SSPC-SP1 and apply a test patch. Allow paint to dry at least
Unit ................................................ 30:1 Pump
one week before testing adhesion. If adhesion is poor, brush blasting per SSPC-SP7 is
Pressure ................................... 2700-3000 psi
necessary to remove these treatments. Rusty galvanizing requires a minimum of Hand Tool
Hose ..................................................... 1/4" ID
Cleaning per SSPC-SP2, prime the area the same day as cleaned. Primer required.
Tip ............................................... .013" - .015"

Filter .................................................. 60 mesh
Concrete and Masonry - For surface preparation, refer to SSPC-SP13/NACE 6, or ICRI No.
Reduction .... As needed up to 15% by volume
310.2R , CSP 1-3. Surfaces should be thoroughly cleaned and dry. Concrete and mortar must
Conventional Spray
be cured at least 28 days @ 75°F (24°C). Surface temperatures must be at least 55°F before
Gun .......................................... DeVilbiss JGA
filling. Surface must be free of laitance, concrete dust, dirt, form release agents, moisture curing
Fluid Nozzle .................................................. E
membranes, loose cement and hardeners. Fill bug holes, air pockets and other voids. Primer
Air Nozzle ................................................. 765
required.
Atomization Pressure ..................... 45-55 PSI

Fluid Pressure ................................ 10-20 PSI
Pre-Finished Siding: (Fluorocarbon, Silicone Polyester, and Polyester Polymers) Remove
Reduction .... As needed up to 15% by volume
oil, grease, dirt, oxides, and other contaminants from the surface by cleaning per SSPC-SP1 or

water blasting per NACE Standard RP-01-72 (caution: excessive blasting pressure may cause
In order to avoid blockage of spray equipment,
warping, use caution). Always check for compatibility of the previously painted surface with the
clean equipment before use or before periods
new coating by applying a test patch of 2 - 3 square feet. Allow to dry thoroughly for 1 week
of extended downtime with water.
before checking adhesion. Use recommended primer.

Brush .................................. Nylon / polyester
APPLICATION PROCEDURES Reduction .... As needed up to 15% by volume
Mix separate components thoroughly with low speed agitation before use. Make certain Water, 5-15% minimum reduction required for brush
no pigment remains on the bottom of the can. Then combine 4 parts by volume of Part A and roll
Roller ........................................... 3/8" woven
with 1 part by volume of Part B. Mix thoroughly with low speed agitation. Reduce 5% -
Reduction .... As needed up to 15% by volume
15% by volume with water for brush and roll application.
Water, 5-15% minimum reduction required for brush

and roll.
Apply paint at the recommended film thickness and spreading rate as indicated on front page.
If specific application equipment is not listed above,
Application of coating above maximum or below minimum recommended spreading rate may equivalent equipment may be substituted.
adversely affect coating performance.
SAFETY PRECAUTIONS

Refer to the SDS sheets before use. CLEANUP INFORMATION
Published technical data and instructions are subject to change without notice. Contact your

Sherwin-Williams representative for additional technical data and instructions.
Clean spills and spatters immediately with

soap and warm water. Clean hands and tools
PERFORMANCE TIPS immediately after use with soap and warm
water. After cleaning, flush spray equipment
Stripe coat crevices, welds, and sharp angles to prevent early failure in these areas.
with compliant cleanup solvent to prevent
Do not mix previously catalyzed material with new.
rusting of the equipment. Follow
Do not apply the material beyond recommended pot life.
manufacturer's safety recommendations when
When using spray application, use a 50% overlap with each pass of the gun to avoid holidays,
using solvents.
bare areas, and pinholes. If necessary, cross spray at a right angle.

KOR,FRC,SP

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of The Sherwin-Williams Company. Such
information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Consult your Sherwin-Williams
representative or visit www.paintdocs.com to obtain the most current version of the PDS and/or an SDS.
SAFETY DATA SHEET
B66N310
Section 1. Identification
Product name : PRO INDUSTRIAL™ PRO-CRYL® Universal Acrylic Primer
Red Oxide
Product code : B66N310
Other means of : Not available.
identification
Product type : Liquid.
Relevant identified uses of the substance or mixture and uses advised against
Not applicable.
Manufacturer : THE SHERWIN-WILLIAMS COMPANY
101 PROSPECT AVENUE, NW
CLEVELAND, OHIO 44115
Emergency telephone : [phone]
number of the company
Product Information : [phone]
Telephone Number
Regulatory Information : [phone]
Telephone Number
Transportation Emergency : [phone]
Telephone Number
Section 2. Hazards identification
OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Classification of the : CARCINOGENICITY - Category 2
substance or mixture
Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 1%
GHS label elements
Hazard pictograms :
Signal word : Warning
Hazard statements : Suspected of causing cancer.
Precautionary statements
Prevention : Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves. Wear eye or face protection.
Wear protective clothing.
Response : IF exposed or concerned: Get medical attention.
Storage : Store locked up.
Disposal Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Supplemental label WARNING: This product contains chemicals known to the State of California to cause
elements cancer and birth defects or other reproductive harm. FOR INDUSTRIAL USE ONLY.
Date of issue/Date of revision :1/21/2016 Date of previous issue :11/27/2015 Version :1.1 1/10
Section 2. Hazards identification
Please refer to the SDS for additional information. Do not transfer contents to other
containers for storage.
Hazards not otherwise :None known.
classified
Section 3. Composition/information on ingredients
Substance/mixture : Mixture
Other means of : Not available.
identification
CAS number/other identifiers
Ingredient name % by weight CAS number
Titanium Dioxide ≥1 - <3 13463-67-7
Carbon Black ≥0.1 - <0.3 1333-86-4
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health and hence require reporting in this section.
Occupational exposure limits, if available, are listed in Section 8.
Section 4. First aid measures
Description of necessary first aid measures
Eye contact : Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. If
not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial
respiration or oxygen by trained personnel. It may be dangerous to the person providing
aid to give mouth-to-mouth resuscitation. Get medical attention. If unconscious, place
in recovery position and get medical attention immediately. Maintain an open airway.
Loosen tight clothing such as a collar, tie, belt or waistband.
Skin contact : Flush contaminated skin with plenty of water. Remove contaminated clothing and
shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing
before reuse. Clean shoes thoroughly before reuse.
Ingestion : Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and
keep at rest in a position comfortable for breathing. If material has been swallowed and
the exposed person is conscious, give small quantities of water to drink. Stop if the
exposed person feels sick as vomiting may be dangerous. Do not induce vomiting
unless directed to do so by medical personnel. If vomiting occurs, the head should be
kept low so that vomit does not enter the lungs. Get medical attention. Never give
anything by mouth to an unconscious person. If unconscious, place in recovery position
and get medical attention immediately. Maintain an open airway. Loosen tight clothing
such as a collar, tie, belt or waistband.
Most important symptoms/effects, acute and delayed
Potential acute health effects
Eye contact : No known significant effects or critical hazards.
Inhalation : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Over-exposure signs/symptoms
Eye contact : No specific data.
Inhalation : No specific data.
Date of issue/Date of revision :1/21/2016 Date of previous issue :11/27/2015 Version :1.1 2/10