PowerSeries Neo Alarm Controller

130 Pages·2014·3.67 MB·English

PowerSeries Neo Alarm Controller
V1.0 Reference Manual
Models:
HS2016/HS2032/HS2064/HS2128
WARNING: This manual contains information on limitations regarding product use and function and
information on the limitations as to liability of the manufacturer. The entire manual should be carefully
read.
Contents
1: Introduction . . . . . . . . . . . . . . . . . . . . 1 Factory Defaults..............................................12
Alternate Communicator Setup...........12
About the System.....................................1
Real Time Clock..............................................13
Features.............................................................1
Communication Paths.....................................13
Available Models..............................................1
Communications Options................................13
Compatible Devices..........................................2
Communication Attempt Limit.......................13
2: Installation . . . . . . . . . . . . . . . . . . . . . 3 Supervision Restore........................................13
Remote Firmware Upgrade.............................13
Overview of Installation Process............3 Local Firmware Upgrade.....................13
Alarm Controller Installation................3 Testing the System.................................13
Mounting the Enclosure....................................3 Walk Test.........................................................13
Wiring.......................................................3 Viewing the Event Buffer................................13
Terminal Descriptions.......................................3
4: System Operation. . . . . . . . . . . . . . . 14
Wire Routing for Power & Non-Power Limited4
Corbus Wiring...................................................4
Arming and Disarming.........................14
Installing Modules...................................5
Partition vs. Global Keypad.................14
Zone Expander..................................................5
Output Expander...............................................5 Labels.....................................................14
Wireless Transceiver Module...........................5 System Label...................................................14
Power Supply Wiring........................................5 Zone Labels.....................................................14
Keypad Wiring..................................................6 Partition Labels...............................................14
Assigning Keypad Zones..................................6 Module Labels.................................................14
Audio Verification Module...............................6 Event Labels....................................................15
Alternate Communicator Wiring......................6 Partition Command Output Labels..................15
Zone Wiring......................................................6
Annunciation.........................................15
PGM Wiring......................................................7
Door Chime.....................................................15
Bell Wiring........................................................7
Temperature Display.......................................15
Telephone Line Wiring.....................................8
Low Temperature Warning..............................15
Smoke Detector Wiring....................................8
Fire Zone Wiring: 2-wire Smoke Detectors......8 Keypad Function Keys.........................15
CO Detector......................................................8 Function Key Definitions................................15
Ground Wiring..................................................9
Language Selection...............................16
Connecting Power.............................................9
[*] Commands.......................................16
3: Configuration. . . . . . . . . . . . . . . . . . 10
[*][1] Bypass or Stay/Away/Night Zones.......17
[*][2] Trouble Display....................................17
Basic Configuration Steps.....................10
[*][3] Alarm Memory Display........................18
Using the Keypad...................................10 [*][4] Door Chime Enable/Disable.................19
Special Keys...................................................10 [*][5] Program Access Codes.........................19
LED Indicators................................................10 [*][6] User Functions......................................21
[*][7] Command Outputs 1-4..........................22
Enrollment..............................................10
[*][8] Installer Programming..........................22
Enrolling Modules..........................................10
[*][9] No-Entry Arming..................................22
Module Supervision.........................................11
[*][0] Quick Arm/Exit.....................................22
Enroll Wireless Devices...................................11
SMS Command and Control................22
Working with Partitions.......................11
SMS Command and Control Functions..........22
Setting Up a Partition.......................................11
Visual Verification.................................23
Bell/Siren Operation........................................11
Trouble Indicators.................................12
5: Programming . . . . . . . . . . . . . . . . . . 24
Keypad Partition Setup.........................12
How to Program....................................24
Global Zones...................................................12
Fire and CO Zone Types.................................12 Programming Methods.........................24
Bell/PGM Support..........................................12
Template Programming...................................24
Communications.............................................12
i
Contents
DLS Programming..........................................24
Installer Programming....................................25
Viewing Programming....................................25
Programming Hex and Decimal Data.............25
Programming Descriptions...................26
Adding Labels.................................................26
Zone Setup......................................................27
System Times..................................................30
Access Codes..................................................30
PGM Configuration........................................31
PGM Types.....................................................31
System Options...............................................37
Partition Setup................................................42
Reporting........................................................43
System Communications................................46
DLS Programming..........................................50
Schedule Programming...................................52
Wireless Programming....................................52
Systems Information.......................................53
Module Programming.....................................53
Testing.............................................................54
Defaults...........................................................54
6: Programming Worksheets . . . . . . . 55
7: Troubleshooting. . . . . . . . . . . . . . . . 93
Testing.....................................................93
Troubleshooting.....................................93
Appendix A : Event Codes . . . . . . . . . 98
Appendix B : Word Library. . . . . . . 104
Appendix C : Template Programming
Tables . . . . . . . . . . . . . . . . . . . . . . . . . 105
Appendix D : Regulatory Approvals 110
UL/ULC Installations....................................111
SIA False Alarm Reduction Installations: Quick
Reference...........................................................................113
Appendix E : ASCII Characters. . . . 114
Appendix F : Wiring Diagrams . . . . 115
Appendix G : Specifications . . . . . . . 119
Appendix H : Index . . . . . . . . . . . . . . 122
ii
Before Installing The Equipment
Ensure your package includes the following items:
• Installation and User manuals, including the SAFETY INSTRUCTIONS.
READ and SAVE these instructions!
Follow all WARNINGS AND INSTRUCTIONS specified within this document and/or on the equipment.
• HS2016/2032/2064/2128 alarm controller
• Power Supply, direct plug-in
• Mounting hardware
Safety Instructions for Service Personnel
Warning: When using equipment connected to the telephone network, always follow the basic safety instructions provided with this product.
Save these instructions for future reference. Inform the end-user of the safety precautions that must be observed when operating this equipment.
Selecting A Suitable Location For The Alarm Controller
Use the following list as a guide to find a suitable location to install this equipment:
• Locate near a telephone socket and power outlet.
• Select a location free from vibration and shock.
• Place alarm controller on a flat, stable surface and follow the installation instructions.
Do NOT locate this product where people may walk on the secondary circuit cable(s).
Do NOT connect alarm controller to electrical the same circuit as large appliances.
Do NOT select a location that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals or dust.
Do not install this equipment near water. (e.g., bath tub, kitchen/laundry sink, wet basement, near a swimming pool).
Do NOT install this equipment and accessories in areas where risk of explosion exists.
Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers.
AVOID interference sources.
AVOID installing equipment near heaters, air conditioners, ventilators, and refrigerators.
AVOID locating equipment close to or on top of large metal objects (e.g., wall studs).
• See page120 for information on locating smoke and CO detectors.
SAFETY Precautions Required During Installation
• NEVER install this equipment and/or telephone wiring during a lightning storm.
• NEVER touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Position cables so that accidents can not occur. Connected cables must NOT be subject to excessive mechanical strain.
• Use only the power supply provided with this equipment. Use of unauthorized power supplies may cause damage.
• For direct plug-in versions, use the transformer supplied with the device.
WARNING:
THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO
SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED. IT IS IMPERATIVE THAT
ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET IS NEVER OBSTRUCTED.
IMPORTANT NOTE!
This alarm system must be installed and used within an environment (a) The equipment enclosure must be secured to the building
that provides the pollution degree max 2 and over-voltages category structure before operation.
II NON-HAZARDOUS LOCATIONS, indoor only. The equipment is (b) Internal wiring must be routed in a manner that prevents:
DIRECT PLUG-IN (external transformer) and is designed to be
- Excessive strain or loosening of wire on terminal connections;
installed, serviced and/or repaired by service persons only; [service
- Damage of conductor insulation
person is defined as a person having the appropriate technical
training and experience necessary to be aware of hazards to which (c) Disposal of used batteries must be made in accordance with
that person may be exposed in performing a task and of measures to local waste recovery and recycling regulations.
minimize the risks to that person or other persons]. There are no (d) Before servicing, DISCONNECT the power and telephone
parts replaceable by the end-user within this equipment. The wiring connection.
(cables) used for installation of the alarm system and accessories, (e) DO NOT route any wiring over circuit boards.
shall be insulated with PVC, TFE, PTFE, FEP, Neoprene or
(f) The installer is responsible to ensure that a readily accessible
Polyamide.
disconnect device is incorporated in the building for permanently
connected installations.
The power supply must be Class II, FAIL SAFE with double or reinforced insulation between the PRIMARY and SECONDARY CIRCUIT/
ENCLOSURE and be an approved type acceptable to the local authorities. All national wiring rules must be observed.
xxv
Section 1: Introduction
1.1 About the System Model Differences
The table below lists the features of each alarm system model.
The PowerSeries Neo alarm panel is a feature-rich, scalable alarm
system designed for residential and light commercial use. The alarm Table 1-1 Model Differences
panel supports both hardwired and wireless devices. This section lists
Features HS2128 HS2064 HS2032 HS2016
the features of the alarm panel, available models, and compatible
Hardwired zones 128 64 32 16
devices.
Onboard zone inputs 8 8 8 6
1.1.1 Features
Wireless zones 128 64 32 16
The following features are available on the PowerSeries Neo alarm
Partitions 8 8 4 2
controller.
Users 95 95 72 48
Zones
Onboard outputs 4 4 2 2
• 16, 32, 64, or 128 wireless zones supported and 8 hardwired
Max outputs 148 80 38 22
zones available on the controller
Keypads 16 8 8 8
• 40 zone types and 14 programmable zone attributes
Wireless keys 32 32 32 16
• Up to 16 separate wireless keypads supported
Wireless sirens 16 8 8 4
• Up to 32 separate wireless keys or panic pendants supported
Wireless repeaters * 8 8 8 4
• Up to 95 separate proximity tags supported
Proximity tags 94 94 71 47
Access Codes
Alt Comm. phone #’s 4 4 4 4
• Up to 98 access codes: one system master code, one installer
code, and one maintenance code User-programmable 8 8 8 8
phone #’s
• Programmable attributes for each user code (see page20)
Lifesafety event buffer 1000 500 500 500
Programmable Outputs (PGMs)
8-zone expander 15 7 3 1
• Up to 4 programmable outputs (PGM) on the alarm controller HSM2108
with 41 available options Power supply 4 3 3 3
• 148, 80, 38, 22 maximum programmable outputs HSM2300
System Supervision Features Power supply/high- 4 3 1 1
current output
• The PowerSeries Neo continuously monitors a number of possi-
expander HSM2204
ble trouble conditions and provides audible and visual indica-
8-output expander 16 8 4 2
tion at the keypad. Trouble conditions include: HSM2208
• AC power failure 2- way wireless inte- 1 1 1 1
• Zone trouble gration module
• Fire trouble Audio verification 1 1 1 1
PC5950
• Telephone line trouble
• Communicator trouble
• Low battery condition *For UL installations, 2 repeaters must be installed for proper signal
routing.
• RF jam
• AUX power supply fault
• Failure to communicate
• Module fault (supervisory or tamper)
Additional Features
• 2-way wireless device support
• Visual verification (images + audio)*
• Proximity tag support
• PGM scheduling
• Quick arming
• User, partition, module, zone and system labels
• Programmable system loop response
• Keypad and panel software versions viewable through keypad
• Doorbell zone type
• Low battery PGM type
1.1.2 Available Models
The following alarm controller models are available:
• HS2016
• HS2032
• HS2064
• HS2128
1
S e c t i o n 1 : I n t r o d u c t i o n
1.1.3 Compatible Devices CO detector CO-12/24UL
The following wireless devices and modules are compatible with this 12-24SIRUL
alarm controller. FW-CO12UL
NOTE: On the chart below and throughout this document, x in the FW-CO1224UL
model number represents the operating frequency of the device as fol- CO1224UL
lows: 9 (912-919 MHz), 8 (868MHz), 4 (433MHz).
Wireless Devices
NOTE: Only models operating in the band 912-919 MHz are UL/ULC
Wireless PG smoke detector PGx926UL
listed where indicated. OnlyUL approved devices are to be used with UL/
ULC listed systems. Wireless PG smoke and heat detector PGx916UL
Wireless PG CO detector PGx913UL
Table 1-2 Compatible Devices
Wireless PG PIR motion detector PGx904(P)UL
Modules
Wireless PG PIR + camera motion PGx934(P)UL
Wireless keypads HS2LCDWFx detector
HS2LCDWFPx
HS2LCDWFPVx Wireless PG curtain motion detector PGx924UL
Hardwired keypads with 2-way wire- HS2LCDRFxUL Wireless PG dual tech motion detec- PGx984(P)
less integration module HS2LCDRFPxUL tor
HS2ICNRFx UL Wireless PG mirror motion detector PGx974(P)UL
HS2ICNRFPxUL Wireless PG outdoor motion detector PGx994UL
Hardwired keypads HS2LCDUL Wireless PG glass break detector PGx912
HS2LCDPUL Wireless PG shock detector PGx935UL
HS2ICNUL
HS2ICNPUL Wireless PG flood detector PGx985UL
HS2LEDUL Wireless PG temperature detector PGx905UL
(indoor use)
2-way wireless integration module HSM2HOSTx UL
Outdoor temperature probe (requires PGTEMP-PROBE
8-zone expander HSM2108UL PGx905)
8-output expander HSM2208UL Wireless PG key PGx939UL
Power supply HSM2300UL Wireless PG key PGx929UL
4 high current output expander HSM2204UL Wireless PG panic key PGx938UL
Alternate communicator 3G2080UL Wireless PG 2-button key PGx949UL
3G2080RUL Wireless PG indoor siren PGx901UL
TTLL228800URLU L Wireless PG outdoor siren PGx911UL
TL2803GUL Wireless PG repeater PGx920UL
TL2803GRUL Wireless PG door/window contact PGx975UL
PCL-422UL Wireless PG door/window contact w/ PGx945UL
Hardwired Devices AUX
2-wire smoke detector FSA-210xUL Central Station Receivers
FSA-210xTUL SG-System I, II, III, IV, 5
x= A, B, or C
FSA-210xSUL Enclosures
A: ULC listed models FSA-210xSTUL
BC:: UEuLr olipseteadn manodd Aelusstralian models FSA-210xLSTUL Tinh teh eH mS2e1ta2l8 e/nHcSlo2s0u6r4e/sH liSs2te0d3 b2e/HloSw2:0 T1a6m mpaeirn p brootaercdt icoann s bwei ticnhsetasl cleadn
FSA-210xRUL be installed on all enclosures, including door opening protection
FSA-210xRTUL and/or removal from the mounting position. Doors can be secured
using screws or keylock.
FSA-210xRSUL • Model PC5003C (removable door) made of 22Ga steel, painted,
FSA-210xRSTUL dimensions: 248mm(L) x 298mm(W) x 76mm(H), weight: 4.5Kg
FSA-210xLRSTUL (with PCB, battery and transformer included)
4-wire smoke detector FSA-410xUL
FSA-410xTUL
x= A, B, or C
FSA-410xSUL
A: ULC listed models FSA-410xSTUL
B: UL listed models FSA-410xLSTUL
C: European and Australian models
FSA-410xRUL
FSA-410xRTUL
FSA-410xRSUL
FSA-410xRSTUL
FSA-410xLRSTUL
2
Section 2: Installation
2.1 Overview of Installation Process 2.2.1 Mounting the Enclosure
The steps below are provided to assist with the installation of the Locate the panel in a dry area, preferably near an unswitched AC
alarm system. Read over this section briefly to get an overall under- power source and the incoming telephone line. Complete all wiring
standing of the order of installation. Working from this plan can help before applying AC or connecting the battery.
reduce problems and reduce the overall time required for installation. 2.3 Wiring
Step 1 – Create a Layout
Draw a rough sketch of the site and include all alarm detection All wiring entry points on the enclosure are designated by arrows. All
devices, zone expanders, keypads and other required modules. circuits are classified UL power limited except for the battery leads.
Minimum 1/4” (6.4mm) separation must be maintained at all points
Step 2 – Mount the Panel
between power limited and non-power limited wiring and connections.
Decide on a location for the alarm panel and secure it to the wall
using suitable mounting hardware. See 2.2.1 Mounting the Enclosure 2.3.1 Terminal Descriptions
on page 3.
The following terminals are available on the PowerSeries Neo alarm
Step 3 – Wire the Alarm Controller controller.
Wire each of the modules to the alarm controller following the guide-
Terminal Description
lines provided in section 2.3.3 Corbus Wiring on page 4.
AC Power terminals.
Step 4 – Wire Zones
Connect the battery before connecting
Complete all zone wiring. Follow the guidelines provided in section
2.4.8 Zone Wiring on page 6 to connect zones using normally closed the AC. Do not connect the battery or
loops, single EOL resistor, double EOL resistors, fire zones and key- transformer until all other wiring is
switch arming zones. complete.
Step 5 – Complete Wiring BAT+, BAT- Battery terminals. Use to provide backup
Complete all other wiring including bells or sirens, telephone line power and additional current when sys-
connections, ground connections or any other wiring necessary. Fol- tem demands exceed the power output of
low the guidelines provided in section 2.3.1 Terminal Descriptions the transformer, such as when the system
on page 3. is in alarm.
Do not connect the battery until all other
Step 6 – Power up the Control Panel
wiring is complete.
Once all zone and alarm controller wiring is complete, connect the
battery and power up the system. The alarm controller will not power AUX+, AUX- Auxiliary terminals. Use to power
up if only the battery is connected. modules, detectors, relays, LEDs, etc.
Step 7 – Enroll Keypads and Modules (700mA MAX). Connect the positive side
All keypads must be enrolled in order to operate on the system. To of device to AUX+, the negative side to
enroll the first keypad, see page11. To enroll optional keypads, see AUX-.
page52.
BELL+, BELL- Bell/Siren power. Connect the positive
Step 8 – Confirm Module Supervision side of any alarm warning device to
By default, all modules are supervised upon installation. Supervision BELL+, the negative side to BELL-.
is enabled at all times. To confirm that each module is properly RED, BLK, YEL, GRN Corbus terminals. Use to provide
supervised, see [903] Confirm Module on page 54.
communication between the alarm
Step 9 – Enroll Wireless Devices controller and connected modules. Each
Wireless devices are enrolled via the wireless transceiver module module has four Corbus terminals that
(HSM2HOSTx) or RF keypad and Installer Programming section must be connected to the Corbus.
[804]. See [804] Wireless Programming on page 52 to enroll wireless
PGM1 to PGM4 Programmable output terminals. Use to
devices.
activate devices such as LEDs.
Step 10 – Program the System
(PGM1, PGM3, and PGM4: 50mA
Section 5 on page24 provides a complete description of how to pro-
PGM2: 300mA or can be configured as an
gram the alarm controller. It contains complete descriptions of the
input)
various programmable features and options. Fill out the program-
ming worksheets starting on page57 completely before attempting to Z1 to Z8 Zone input terminals. Ideally, each zone
program the system. COM should have one detection device; how-
ever, multiple detection devices can be
Step 11 – Test the System
wired to the same zone.
Test the panel completely to ensure that all features and functions
operate as programmed. TIP, RING, T-1, R-1 Telephone line terminals.
EGND Earth ground connection.
2.2 Alarm Controller Installation
PCLINK_1 DLS/SA
Begin the installation by mounting the alarm controller in the metal
PCLINK_2 DLS/SA, Alternate Communicator
enclosure using the stand-offs provided. Optional modules, such as
the HSM2108 and HSM2208, can also be mounted in the enclosure.
Install hardware in the sequence indicated on the following pages.
3
S e c t i o n 2 : I n s t a l l a t i o n
2.3.2 Wire Routing for Power & Non-Power Table 2-1: System Output Ratings
Limited
Device Output Rating (12VDC)
All wiring entry points are designated on the diagram by arrows. All HS2016 AUX: 700mA. Subtract the listed rating for each
circuits are classified UL installation power limited except for the
HS2032 keypad, expansion module and accessory
battery leads which are not power limited.
HS2064 connected to AUX or Corbus. At least
A minimum ¼” (6.4mm) separation must be maintained at all points
HS2128 100mA must be reserved for the Corbus.
between power limited and non-power limited wiring and connec-
BELL: 700mA. continuous rating.
tions. See page115 for expanded diagrams.
2.0A. short term. Available only with
Diagram 2-1: Wiring Routing
standby battery connected. Not for UL/
North America Only
POWER LIMITED ULC or EN certified applications
HSM2208 AUX: 250mA.Continuous rating. Subtract for
PC Board Stand Off CableTie (not supplied) recommended
each device connected. Subtract the total
Cabinet UA503 DSC load on this terminal from the alarm panel
HS2016/032/064/128
AUX/Corbus output.
WARNING:
HighVoltage.Disconnect ACPo wer HSM2108 AUX: 100mA. Subtract for each device
and telephone lines before servicing
connected. Subtract the total load on this
SDCPelSraciCmsosPna TIIdrDya :Tr11ry62a:40n10Vs6Uf.A5oCVrm/D6Ce0r H40z.VA BACTO+NB1AT- A C+AUX-+BELL-REDBLKYELGRN1PGM2HHH 3 OSSSP222nG001lMy162648-44Z1COMZ2Z3COMZ4Z5COMZ6ZHHHH7SSSSOC2222O0010nM3621ly2486-4Z8GNDRingTipR-1T-1TB-2 toeurtmpuint.al from the panel AUX/Corbus
NOTE:Do not connect
tcroanntsrfoollremde br yto a r sewceitpchtacle PE (Protective Earth) Alarm Controller Current Calculation
Maximum (Standby or Alarm)
12V / 7 AHr 12V / 7 AHr AUX (700mA max. including
BLACK PGMs 1-4)
RED
NON-POWER LIMITED DSCo Mr eoqdueilv BaDle7n-t12 Corbus (700mA max.)***
Battery
StandbyTime:
24Hrs min.
PCLink+ (Alt. Com.:125mA)
NOTE: Wire entry for power limited wiring must be separated by a dif-
ferent entry access from non-power limited wiring.
2.3.3 Corbus Wiring
Total (must not exceed 700mA)
The RED and BLK Corbus terminals are used to provide power
while YEL and GRN are used for data communications. The 4 Cor-
***See Corbus Current Calculation Chart.
bus terminals of the alarm controller must be connected to the 4 Cor-
bus terminals or wires of each module. For UL, ULC and Commercial Listed applications, the total standby and
alarm current cannot exceed 700mA.
The following conditions apply:
• Corbus should be run with minimum 22 gauge quad. two pair Table 2-2:Corbus Current Calculation Chart
twisted preferred.
Item Current (mA) x Quantity Total (mA)
• The modules can be home run to the panel, connected in series
HS2LCD 100 x
or can be T-tapped.
HS2ICN 100 x
NOTE: Any module can be connected anywhere along the Corbus. Sep-
HS2LED 100 x
arate wire runs for keypads, zone expanders etc. are not necessary.
HS2LCDP 100 x
NOTE: No module can be more than 1,000'/305m (in wire length) from
the panel. Do not use shielded wire for Corbus wiring. HS2ICNP 100 x
HS2LCDRF 100 x
Diagram 2-2: Corbus Wiring
HS2ICNRF 100 x
Module (A) is wired correctly as it is
within 1,000'/305m of the panel, in HS2ICNRFP 100 x
wire distance. Module (B) is wired Current required for connected devices =
correctly as it is within 1,000'/305m HSM2108* 30 x
of the panel, in wire distance. Module
HSM2208* 40 x
(C) is NOT wired correctly as it is
HSM2300/2204* 35 x
farther than 1,000'/305m from the
panel. HSM2HOSTx 35 x
3G2080(R)/ 125 (PCLINK) x
Current Ratings
TL2803G(R)/
In order for the system to operate properly, the power output of the
TL280(R)
alarm controller and power supply modules cannot be exceeded. Use
Total Corbus Current =
the data below to ensure that the available current is not exceeded.
*These units draw current from the Corbus to power devices external
to the module. This current must be added to the total Corbus current.
See manufacturer's specifications for the current draw of each device.
4
S e c t i o n 2 : I n s t a l l a t i o n
Line Loss 2.4.2 Output Expander
Voltage loss through wire resistance must be considered for all instal- The HSM2208 module is used to add up to 8 low-current programmable
lations. To ensure proper operation, at least 12.5VDC must be applied outputs to the alarm system.
to all modules on the system (when AC is connected and the battery The 4-wire Corbus connection is used by the panel to communicate with
is fully charged). If less than 12.5VDC is applied, system operation is the module. Connect the RED, BLK, YEL and GRN terminals to the
adversely affected. Corbus terminals on the alarm panel. Board current draw: 40mA.
To correct the problem, try any or all of the following:
Diagram 2-4: HSM2208 Output Expander
1. Connect an HSM2300/2204 power supply between the alarm

controller and the module to provide power to the Corbus.
SERIAL NUMBER
2. Reduce the length of the Corbus run to the module.
3. Increase the gauge of wire. SWITCH
LED
Capacitance Limits
An increase in capacitance on the Corbus affects data transmission
and causes the system to slow down. Capacitance increases for every
foot of wire added to the Corbus. The capacitance rating of the wire
used will determine the maximum length of the Corbus.
For example, 22-gauge, non-shielded, 4-conductor wire has a typical
capacitance rating of 20 picofarads per foot (which is 20nF/1000’).
For every 1000' of wire added – regardless of where it is run – the
capacitance of the Corbus increases by 20nF. 2.4.3 Wireless Transceiver Module
The following chart indicates the total wire distance allowed for the
The HSM2HOSTx 2-way wireless integration module provides com-
capacitance rating of the wire used:
munication between wireless devices and the alarm controller.
Table 2-3: Wire Capacitance Connect the HSM2HOSTx to the 4-wire Corbus of the alarm control-
ler according to the diagram below.
Wire Capacitance per 1000’
(300m) Total Corbus Wire Length Diagram 2-5: HSM2HOSTx Wiring Diagram
15nF 5300’/1616m
20nF 4000’/1220m
25nF 3200’/976m
30nF 2666’/810m
35nF 2280’/693m
CORBUS TO
40nF 2000’/608m HSM2HOST
2.4 Installing Modules After you have completed the wiring, reconnect power to the security
system. Board currant draw: 35mA
Remove all power from the system while connecting modules to the
alarm controller. 2.4.4 Power Supply Wiring
2.4.1 Zone Expander The HSM2300/2204 power supply/high-current output module pro-
vides up to 1.0A of additional current and can be used to add up to
The main alarm controller has connection terminals for zones 1 to 8.
four programmable outputs (HSM2204 only) to the alarm system.
Additional HSM2108 zone expanders may be added to increase the
The 4-wire Corbus connection provides communication between the
number of zones on the system. Each zone expander consists of one
module and alarm panel. Connect the RED, BLK, YEL & GRN ter-
group of 8 zones. At enrollment, the zone expander is automatically
minals to the RED, BLK, YEL & GRN Corbus terminals on the
assigned to the next available zone slot. Connect the RED, BLK,
alarm controller. If O1 is not used, connect to Aux with a 1K resistor.
YEL and GRN terminals to the Corbus terminals on the alarm panel.
Board current draw: 1.2A.
Board current draw: 30mA.
Diagram 2-6: Power Supply Wiring
Diagram 2-3: HSM2108 Zone Expander
SERIAL NUMBER
SWITCH
LED Residential
Burglary
BACTO+ N B1AT-
RED* BLK*YELGRN
SaBmB1A2aeTtV Trt aeE 7trRiyAnY h1g 2 as MchaaxBri1mAg32Te6uV T0cm E um7R rAbrYAeah 1tntte irsy MchaaxriB1mg32Ae6uVT 0cm T um7E rAbRrAeahYtntte irsy 1P2r60i0mVHAazrCy/TRANSFORMER BTLOK
Battery standby capacity is at least for 24 hours for Fire 1P6.T5DV1A6C4 /0 4U0 V/ A RED
Refer to the HSM2108 installation sheet for more information. ARepcpolimcamtieonnds.ed Battery: DSC model BD7-12. EAUus, tSraoliuat,h N AZPfrT eiDctac1,:6 40 EXMPAOAUTNDOXSU *I*LOEN GBYRLEKNL CTOOKN CPENAOYENNBCEUTTLRSIOONL
primary 230VAC/ 50/60Hz
* Red, Blk, 12 VDC @ 20mA
** Refer to the Specifications Chart above for
the maximum current draw.
5
S e c t i o n 2 : I n s t a l l a t i o n
2.4.5 Keypad Wiring Diagram 2-8: PC5950 Wiring Diagram
To wire a keypad to the alarm controller, remove the keypad back-
B Universal Configuration Wiring Diagram
plate (refer to the keypad installation sheet) and connect the R, B, Y, (Positive Bell Drive from Panel)
and G terminals to the corresponding terminals on the alarm control-
ler.
*Panel
*NOTE: Connections may vary
Keypad Zone/PGM Wiring depending on configuration
PGM
Hardwired devices can be connected to hardwired keypads with AUXCOM 1 2 + BELL- ZONE
SIREN
inputs (zone) or outputs (PGM). This saves from running wires back EOLR
to the control panel for every device.
To connect a zone device to HS2LCD, HS2ICON and HS2LED key-
pads, run one wire to the P/Z terminal and the other to B. For pow-
NOTE(cid:29)(cid:3)(cid:36)(cid:81)(cid:3)(cid:53)(cid:48)(cid:20)(cid:18)(cid:53)(cid:48)(cid:20)(cid:38)(cid:3)(cid:85)(cid:72)(cid:79)(cid:68)(cid:92)(cid:3)
ered devices, use red and black to supply power to the device. Run (cid:76)(cid:86)(cid:3)(cid:85)(cid:72)(cid:84)(cid:88)(cid:76)(cid:85)(cid:72)(cid:71)(cid:3)(cid:76)(cid:81)(cid:3)(cid:82)(cid:85)(cid:71)(cid:72)(cid:85)(cid:3)(cid:87)(cid:82)(cid:3)
the red wire to the R (positive) terminal and the black wire to the B (cid:86)(cid:88)(cid:83)(cid:83)(cid:85)(cid:72)(cid:86)(cid:86)(cid:3)(cid:37)(cid:72)(cid:79)(cid:79)(cid:3)(cid:55)(cid:85)(cid:82)(cid:88)(cid:69)(cid:79)(cid:72)(cid:3)
(cid:76)(cid:81)(cid:71)(cid:76)(cid:70)(cid:68)(cid:87)(cid:76)(cid:82)(cid:81)(cid:17)(cid:3)(cid:37)(cid:72)(cid:79)(cid:79)(cid:3)(cid:55)(cid:85)(cid:82)(cid:88)(cid:69)(cid:79)(cid:72)(cid:3)(cid:90)(cid:76)(cid:79)(cid:79)(cid:3)
(negative) terminal. (cid:82)(cid:70)(cid:70)(cid:88)(cid:85)(cid:3)(cid:76)(cid:73)(cid:3)(cid:68)(cid:88)(cid:71)(cid:76)(cid:82)(cid:3)(cid:86)(cid:72)(cid:86)(cid:86)(cid:76)(cid:82)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)
(cid:79)(cid:82)(cid:81)(cid:74)(cid:72)(cid:85)(cid:3)(cid:87)(cid:75)(cid:68)(cid:81)(cid:3)(cid:37)(cid:72)(cid:79)(cid:79)(cid:3)(cid:55)(cid:76)(cid:80)(cid:72)(cid:16)(cid:82)(cid:88)(cid:87)(cid:17)
Keypad zones support Normally Closed Loops, Single End of Line
RM1 / RM1C
and Double End of Line.
Bell (Siren)
(cid:44)(cid:73)(cid:3)(cid:81)(cid:82)(cid:3)(cid:86)(cid:76)(cid:85)(cid:72)(cid:81)(cid:3)(cid:76)(cid:86)(cid:3)(cid:85)(cid:72)(cid:84)(cid:88)(cid:76)(cid:85)(cid:72)(cid:71)(cid:15)(cid:3)
To connect the PGM output, run one wire to the P terminal and the (cid:85)(cid:72)(cid:83)(cid:79)(cid:68)(cid:70)(cid:72)(cid:3)(cid:86)(cid:76)(cid:85)(cid:72)(cid:81)(cid:18)(cid:40)(cid:50)(cid:47)(cid:53)(cid:3)(cid:90)(cid:76)(cid:87)(cid:75)(cid:3)(cid:68)(cid:3)
other to R. (cid:20)(cid:19)(cid:19)(cid:19)(cid:3)(cid:50)(cid:75)(cid:80)(cid:3)(cid:19)(cid:17)(cid:24)(cid:58)(cid:3)(cid:85)(cid:72)(cid:86)(cid:76)(cid:86)(cid:87)(cid:82)(cid:85)(cid:17)
Diagram 2-7: Keypad P/Z Terminals Trg/
EnbEnb SIREN / EOLR
RED REDBLKYELGRN + - TAM OFF
BELL RNG To outside
BLK TIP phone line
PC5950 R-1
YEL T-1
M1M2M3M4SPK1 SPK2 AUXCOM
GRN
To zone or
PGM output AuxCom AuxCom AuxCom AuxCom
NOTE: When using end of line supervision, connect the zone according Audio Audio Audio Audio
Station Station Station Station
to one of the configurations outlined in Section 2.4.8.. End of line resis- Mic Spkr Mic Spkr Mic Spkr Mic Spkr
tors must be placed on the device end of the loop, not at the keypad.
Assigning Keypad Zones
2.4.7 Alternate Communicator Wiring
When using keypad zone inputs, each input used must be assigned a
zone number in Installer Programming. See Alternate Communicator installation manual.
First, ensure that you have enrolled all installed keypads into the
2.4.8 Zone Wiring
desired slots (See “[902] Add/Remove Modules” on page53). Next,
assign keypad zones by entering programming section [861]-[876], Power down the alarm controller and complete all zone wiring.
subsection 011 for keypads 1-16. Enter a 3-digit zone number for Zones can be wired to supervise normally open devices (e.g., smoke
each of the keypad zones. This number must be programmed into the detectors) or normally closed devices (e.g., door contacts). The alarm
slot location that the keypad is assigned to. panel can also be programmed for single end-of-line or double end-
NOTE: If a keypad zone input is assigned to zone number 1 to 8, the of-line resistors.
corresponding zone cannot be used on the main control panel. Zone programming is done using the following programming sec-
Once the keypad zones are assigned, you must also program zone tions:
definitions and zone attributes. See “[001] Zone Type” on page27 • [001] selects zone definition
and [002] Zone Attributes on page 29. • [013] Opt [1] for normally closed or EOL; Opt [2] for SEOL or
DEOL
2.4.6 Audio Verification Module
Observe the following guidelines when wiring zones:
(Non-UL listed systems only)
• For UL listed installations use SEOL or DEOL only
The PC5950 Universal VOX Audio Verification module provides • Minimum 22 AWG wire, maximum 18 AWG
“talk/listen-in” capability for audio verification of alarms. The mod-
• Do not use shielded wire
ule permits the central station to monitor microphones and communi-
• Do not exceed 100 wire resistance. Refer to the chart below:
cate to occupants through speakers. The following diagram illustrates
how to wire the PC5950 to the alarm control panel and listening sta- Table 2-4: Burglary Zone Wiring Chart
tions.
Wire Maximum Length to
Gauge EOL Resistor (ft/meters)
22 3000 / 914
20 4900 / 1493
19 6200 / 1889
18 7800 / 2377
Figures are based on maximum wiring resistance of 100
6