Materials Design and Applications

416 Pages·2017·17.868 MB·English

by  Lucas F. M. da Silva (eds.)

Advanced Structured Materials
Lucas F.M. da Silva Editor
Materials
Design and
Applications
Advanced Structured Materials
Volume 65
Series editors
Andreas Öchsner, Southport Queensland, Australia
Lucas F.M. da Silva, Porto, Portugal
Holm Altenbach, Magdeburg, Germany
More information about this series at http://www.springer.com/series/8611
Lucas F.M. da Silva
Editor
Materials Design
and Applications
123
Editor
Lucas F.M.daSilva
Department ofMechanical Engineering
Faculty of Engineering ofthe University
ofPorto
Porto
Portugal
ISSN 1869-8433 ISSN 1869-8441 (electronic)
AdvancedStructured Materials
ISBN978-3-319-50783-5 ISBN978-3-319-50784-2 (eBook)
DOI 10.1007/978-3-319-50784-2
LibraryofCongressControlNumber:2016960268
©SpringerInternationalPublishingAG2017
Thisworkissubjecttocopyright.AllrightsarereservedbythePublisher,whetherthewholeorpart
of the material is concerned, specifically the rights of translation, reprinting, reuse of illustrations,
recitation, broadcasting, reproduction on microfilms or in any other physical way, and transmission
orinformationstorageandretrieval,electronicadaptation,computersoftware,orbysimilarordissimilar
methodologynowknownorhereafterdeveloped.
The use of general descriptive names, registered names, trademarks, service marks, etc. in this
publicationdoesnotimply,evenintheabsenceofaspecificstatement,thatsuchnamesareexemptfrom
therelevantprotectivelawsandregulationsandthereforefreeforgeneraluse.
The publisher, the authors and the editors are safe to assume that the advice and information in this
book are believed to be true and accurate at the date of publication. Neither the publisher nor the
authorsortheeditorsgiveawarranty,expressorimplied,withrespecttothematerialcontainedhereinor
foranyerrorsoromissionsthatmayhavebeenmade.
Printedonacid-freepaper
ThisSpringerimprintispublishedbySpringerNature
TheregisteredcompanyisSpringerInternationalPublishingAG
Theregisteredcompanyaddressis:Gewerbestrasse11,6330Cham,Switzerland
Preface
This volume of Advanced Structured Materials contains selected papers presented
at the 1st International Conference on Materials Design and Applications 2016
(MDA2016),heldinPorto,Portugal,duringJune30–July1,2016.Thegoalofthe
conference was to provide a unique opportunity to exchange information, present
the latest results, as well as discuss issues relevant to materials design and appli-
cations. The focus is on fundamental research and application areas in the field
of the design and application of engineering materials, predominantly within the
context of mechanical engineering applications such as automobile, railway, mar-
ine, aerospace, biomedical, pressure vessel technology, and turbine technology.
This includes a wide range of materials engineering and technology, including
metals, e.g., lightweight metallic materials, polymers, composites, and ceramics.
Advanced applications include manufacturing in the new materials, testing meth-
ods, and multi-scale experimental and computational aspects (e.g., microscale and
nanoscale techniques). Approximately, 150 papers were presented by researchers
from nearly 30 countries.
In order to disseminate thework presented in MDA 2016, selected papers were
prepared which resulted in the present volume dedicated to ‘Materials Design and
Applications.’ A wide range of topics are covered resulting in 31 excellent papers
dealing with metals, ceramics, composites, design, power generation, additive
manufacturing, machining, and joining. This book is state of the art of materials
design and applications and also serves as a reference volume for researchers and
graduate students working with advanced materials.
Theorganizerandeditorwishtothankalltheauthorsfortheirparticipationand
cooperation, which made this volume possible. Finally, I would like to thank the
team of Springer-Verlag, especially Dr. Christoph Baumann, for the excellent
cooperation during the preparation of this volume.
Porto, Portugal Lucas F.M. da Silva
September 2016
v
Contents
Part I Metals
Selected Properties of P/M Ti-6Al-2Sn-4Zr-6Mo Alloy
After Hot Deformation.. .... ..... .... .... .... .... .... ..... .... 3
M. Wojtaszek, T. Śleboda and G. Korpała
Positron Annihilation Study on Nanocrystalline Copper
Thin Films Doped with Nitrogen... .... .... .... .... .... ..... .... 15
P.M. Gordo, M.F. Ferreira Marques and M.T. Vieira
The Influence of Microstructure on the Mechanical Behaviour
of Dual Phase Steels .... .... ..... .... .... .... .... .... ..... .... 25
R. Amaral, A.D. Santos, J.A. Sousa and A.B. Lopes
Part II Ceramics
Application of Cutting Edges with High Durability Made
of Nanocrystalline Cemented Carbides .. .... .... .... .... ..... .... 39
Maciej Jan Kupczyk, Piotr Siwak and Jedrzej Komolka
Design of Nanocrystalline Cemented Carbides with High Hardness........ 49
Maciej Jan Kupczyk
Probing Oxygen Vacancies in BaTiO Powders and Single
3
Crystals by Micro-Raman Scattering ... .... .... .... .... ..... .... 65
Hiroaki Fukushima, Hirotaka Oka, Hiroki Moriwake, Hiroshi Uchida,
Hiroshi Funakubo and Ken Nishida
Part III Composites
Investigation of Film Formation and Electrical Properties
of PS Latex/MWCNT Nanocomposites .. .... .... .... .... ..... .... 79
Saziye Ugur, Okan Yildiz and Selim Kara
vii
viii Contents
Cellulose Nanowhiskers Obtained from Waste Recycling
of Paper Industry .. .... .... ..... .... .... .... .... .... ..... .... 101
Alana G. Souza, Daniel B. Rocha and Derval S. Rosa
Coffee Powder Reused as a Composite Material... .... .... ..... .... 113
Vasco Canavarro, Jorge L. Alves and Bárbara Rangel
Comparison of Mechanical Properties of Polyester Composites
Reinforced with Autochthonous Natural Fibres: Flax and Hemp.. .... 125
J. Rocha, J.E. Ribeiro and L. Queijo
Advanced Epoxy-Based Anticorrosion Coatings Containing
Graphite Oxide.... .... .... ..... .... .... .... .... .... ..... .... 135
Monica Periolatto, Elisabetta Di Francia, Marco Sangermano,
Sabrina Grassini and Pasquale Russo Spena
Part IV Design
A Numerical Study of Fenestral Otosclerosis . .... .... .... ..... .... 147
B. Areias, M.P.L. Parente, F. Gentil and R.M. Natal Jorge
Development and Validation of a Numerical Model
for the Optimization of a Brace for Lower Limb.. .... .... ..... .... 157
G. Bellavita, M. Cocconcelli, D. Castagnetti and R. Rubini
Part V Power Generation
Electrical and Geometrical Optimization for a 2DoF
Non-linear Energy Harvester. ..... .... .... .... .... .... ..... .... 173
E. Boco, R. Frizzell and J. Punch
Nonlinear Analysis of a Two-Degree-of-Freedom Energy Harvester........ 187
Valeria Nico, Ronan Frizzell and Jeff Punch
Experimental Investigations of MR Fluids in Air and Water
Used for Brakes and Clutches ..... .... .... .... .... .... ..... .... 197
Alin Ilie Bosioc, Trandafir Emanuel Beja, Sebastian Muntean,
Istvan Borbáth and Ladislau Vékás
Hydrodynamic Investigations in a Swirl Generator Using
a Magneto-Rheological Brake ..... .... .... .... .... .... ..... .... 209
Sebastian Muntean, Alin Ilie Bosioc, Raul Alexandru Szakal,
Ladislau Vékás and Romeo Florin Susan-Resiga
Contents ix
Part VI Additive Manufacturing
Direct Digital Manufacturing: A Challenge to the Artistic
Glass Production... .... .... ..... .... .... .... .... .... ..... .... 221
R. Felismina, M. Silva, A. Mateus and C. Malça
Post-process Influence of Infiltration on Binder Jetting Technology........ 233
Edwin Ocaña Garzón, Jorge Lino Alves and Rui J. Neto
Development of Plaster Mixtures Formulations for Additive
Manufacturing. .... .... .... ..... .... .... .... .... .... ..... .... 257
D.E. Caetano, J.L. Alves, R.L. Neto and T.P. Duarte
Part VII Machining
FE Modal and Harmonic Analysis of Micro Drill
with Ultrasonic Horn ... .... ..... .... .... .... .... .... ..... .... 281
MudduAllaparthi,MohammedRajikKhanandSyamNarayanaAddepalli
Optimization of Machining Parameters to Minimize Surface
Roughness in the Turning of Carbon-Filled and Glass
Fiber-Filled Polytetrafluoroethylene. .... .... .... .... .... ..... .... 295
Muhammet Emre Sanci, Serdar Halis and Yavuz Kaplan
Investigation and Application of Fe–Co−Cu Based Diamond
Cutting Tools with Different Bronze Content Used in Marble
Production.... .... .... .... ..... .... .... .... .... .... ..... .... 307
Berrak Bulut, Onur Tazegul, Murat Baydogan and Eyup Sabri Kayali
Investigation of Surface Roughness and Tool Wear in End
Milling of Al7075-SiC Co-continuous Composite .. .... .... ..... .... 315
A.S. Prasanth and R. Ramesh
Machinability of an Aluminium Cast Alloy Using PCD
Tools for Turning.. .... .... ..... .... .... .... .... .... ..... .... 329
R.B. Soares, A.M.P. de Jesus, R.J.L. Neto, P.A.R. Rosa, M. Machado
and A. Reis
Optimization of Geometric Quality in a 5 Axis Machining
of Curved Surfaces in a EN-AW-7075 Alloy by Taguchi Method.. .... 347
K. Castro, L.J. Segura, S.D. Castellanos and J. Lino Alves
Part VIII Joining
The Production-Related Influence of Iron Oxides on Steel
Surfaces on the Adhesion of Fusion-Bonded Hybrid Structures ... .... 363
T. Reincke, S. Kreling and K. Dilger
x Contents
Comparison of Stepped, Curved, and S-Type Lap Joints
Under Tensile Loading.. .... ..... .... .... .... .... .... ..... .... 377
Şerif Çitil
Bonding Strength of Hot-Formed Steel with an AlSi Coating
and Approaches to Improve It by Laser Surface Engineering .... .... 389
Alexander Wieczorek, Matthias Graul and Klaus Dilger
Micro Cork Particles as Adhesive Reinforcement Material
for Brittle Resins... .... .... ..... .... .... .... .... .... ..... .... 399
A.Q. Barbosa, L.F.M. da Silva, A. Öchsner, E.A.S. Marques
and J. Abenojar
Magnetic Pulse Welding of Dissimilar Materials:
Aluminum-Copper . .... .... ..... .... .... .... .... .... ..... .... 419
I.V. Oliveira, A.J. Cavaleiro, G.A. Taber and A. Reis