manual addendum

278 Pages·2006·2.62 MB·English

SITRANS F
Ultrasonic Flowmeters
SITRANS 1010AERWDP Portable Flowmeter

O p e r a t i n g I n s t r u c t ions
Edition 12/2014
Answers for industry.

IMPORTANT NOTICE
Controlotron is now part of:
Siemens Industry, Inc.
Industry Automation Division
CoC Ultrasonic Flow
Hauppauge, NY 11788 USA
1010AERWDP
UNIFLOW UNIVERSAL
PORTABLE FLOWMETER
This equipment contains components that are
susceptible to electrostatic discharge (ESD).
Please observe ESD control measures during
the handling and connection process.
Field Manual A5E02617285 Rev AB
December 2014
For use with Operating System
Software Version 3.01.06F or later
Copyright©2014 Siemens Industry, Inc. All Rights Reserved Made in the USA
Manual Changes
NOTE: For the latest updates and revisions to this field manual go to:
http://support.automation.siemens.com/ and check the Product Manual listing.
1010FMA-56
MANUAL
ADDENDUM
Operating System Software
Version Update
Manual Addendum
September 2008
Copyright © 2008 Siemens Industry, Inc. All rights reserved Made in the USA

Manual Addendum 1010FMA-56
Operating System Software Version Update
INTRODUCTION
The following software operating system version update is for Version 3 flowmeters. Please refer to
this addendum when using this technical manual with Version 3 operating system software and
flowmeters that have been updated to Version 5.
Operating System Software Changes
1. The [Meter Type Menu] includes a [Language] menu item that allows the selection of multiple flowmeter
menu foreign languages.
2. Version 3 and Version 5 Operating System Differences
The following table lists the differences between Version 3 and Version 5 operating system menu
items and menu hint lines.

Version 3 Version 5
Select Pipe Class Pick Pipe Class
Pick/Install Xdcr Install Xdcr
Data/Span/Set/Ca Span/Set/Cal
Strip Chart Setup Display Setup
Dual Channel Flow 2 Channel Flow
Dual Beam Flow Dual Path Flow
Datalogger Setup Logger Setup
Temperature Range Temp Range
Pipe Configuration Pipe Config
Datalogger Setup Logger Setup
Datalogger Mode Logger Mode
Datalogger Data Logger Data
Log Time Interval Logger Interval
Display Datalogger Display Logger
Recall Site Setup Recall Site
Delete Site Setup Delete Site
Install Completed? Install Complete
Estimated Vs m/s Estimated Vs M/S
Channel /Path Setup Channel Setup
Reflexor Zero Fault/Set Zero Fault/Set
Memory Delay (sec) Memory Delay s)
Flow Volume Units Flow Vol. Units
Flow Display Range Flow Disp. Range
Flow Display Scale Flow Disp. Scale
Total Volume Units Total Vol. Units
Batch/Sample Total Batch/Sample Tot
Calibrate Flowrate Calib. Flowrate
Analog Input Setup Analog Inp Setup
Flow Vel F/S Velocity F/S
Vs m/s Vs M/S
Valc % Valc
Vaer % Vaer
Vs Max m/s Vs Max M/S
(continued )
A-1
Manual Addendum 1010FMA-56
Version 3 Version 5
Vs Min m/s Vs Min M/S
Channel/Path Setup Chan/Path Setup
Vfmax GAL/MIN Vfmax
Date Site Created: Site Created:
Empty % Empty
Analog Output Trim Analog Out Trim
Pick flowtube size and type Select flowtube
and start operation
Empty Flowtube Set Empty Pipe Set
Gas Flowmeter Flow and VoS Unit Changes
1. Flowmeter Types
Flowmeter configurations included with this change include all SITRANS F Gas Flowmeters (7ME361*).
2. Flow Units
The table below describes the translation from the current gas flow units to the new gas flow units,
where only Cubic Feet and Cubic Meter volume units are affected. Also note that M = thousands and
MM = millions. Mass units and Velocity units remain unchanged.
Note: The flow legend changes depending upon the selection of Standard Volume enabled or
disabled.
FLOW UNITS
For STD VOLUME disabled For STD VOLUME enabled
Version 3 Version 5 Version 3 Version 5
CU FT/SEC ACFS CU FT/SEC SCFS
CU FT/MIN ACFM CU FT/MIN SCFM
CU FT/HR ACFH CU FT/HR SCFH
CU FT/DAY ACFD CU FT/DAY SCFD
KCU FT/SEC MACFS KCU FT/SEC MSCFS
KCU FT/MIN MACFM KCU FT/MIN MSCFM
KCU FT/HR MACFH KCU FT/HR MSCFH
KCU FT/DAY MACFD KCU FT/DAY MSCFD
MCU FT/SEC MMACFS MCU FT/SEC MMSCFS
MCU FT/MIN MMACFM MCU FT/MIN MMSCFM
MCU FT/HR MMACFH MCU FT/HR MMSCFH
MCU FT/DAY MMACFD MCU FT/DAY MMSCFD
CU M/SEC M3/sec M/SEC NM3/sec
CU M/MIN M3/min CU M/MIN NM3/min
CU M/HR M3/hr CU M/HR NM3/hr
CU M/DAY M3/day CU M/DAY NM3/day
KCU M/SEC E3 M3/sec KCU M/SEC E3 NM3/sec
KCU M/MIN E3 M3/min KCU M/MIN E3 NM3/min
KCU M/HR E3 M3/hr KCU M/HR E3 NM3/hr
KCU M/DAY E3 M3/day KCU M/DAY E3 NM3/day
MCU M/SEC E6 M3/sec MCU M/SEC E6 NM3/sec
MCU M/MIN E6 M3/min MCU M/MIN E6 NM3/min
MCU M/HR E6 M3/hr MCU M/HR E6 NM3/hr
MCU M/DAY E6 M3/day MCU M/DAY E6 NM3/day
A-2
Manual Addendum 1010FMA-56
3. Total Units
Total units are similar to flow units.
TOTALIZE UNITS
For STD VOLUME disabled
Version 3 Version 5
CU FT ACF
KCU FT MACF
MCU FT MMACF
CUM M3
KCU M E3 M3
MCU M E6 M3
TOTALIZE UNITS
For STD VOLUME enabled
Version 3 Version 5
CU FT SCF
KCU FT MSCF
MCU FT MMSCF
CUM NM3
KCU M E3 NM3
MCU M E6 NM3
4. Sound Velocity Units
Sound velocity will continue to be reported in units of meters/sec for metric units but will change to
Feet/sec for English unit selection. The flowmeter will display M/S and F/S to represent these two
variations.
Note: The units for Sound Velocity will be based on the [Preferred Units] menu item found in
the [Meter Facilities] menu and can not be changed unless a new site is created.
5. Transducer Model Menu Name
The following table lists the operating system menu item differences between Version 3 Hi Precision
and Version 5 Hi Precision transducer model names that appear on the [Install Xdcr] menu. Note that
T1, T2 and T3 indicate the different temperature ranges of the transducer.
Version 3 Transducers Version 5 Transducers
Hi Precision Hi Precision
1011HG Hi Prec. 1011HP-T1
1011HP-T2
1011HP-T3
A-3