K-1463-V-AB, K-1463-H-AB, K-1464-V-AB, K-1464-H-AB, K-1472-V-AB, K-1472-H-AB, K-1474-V

24 Pages·2004·0.32 MB·English

by  Consumber Affairs 1993

(cid:1)

Infinity Whirlpool Baths:
K-1463-V-AB K-1463-H-AB
K-1463-JA-AA K-1464-V-AB
K-1464-H-AB K-1464-JA-AA
K-1472-V-AB K-1472-H-AB
K-1472-JA-AA K-1474-V-AB
K-1474-H-AB K-1474-JA-AA
K-1482-H-AB K-1482-JA-AA
K-1484-H-AB K-1484-JA-AA
112130-CA (1093) Copyright(cid:2)1993 Kohler Co.
IMPORTANT SAFETY INSTRUCTIONS
ATTENTION INSTALLER: INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS
READ AND FOLLOW ALL INSTRUCTIONS
WARNING: When using this unit, always follow basic precautions, including the following:
A pressure wire connector marked ground is provided
DANGER: RISK OF ELECTRICAL SHOCK.
within the terminal compartment. To reduce the risk of
The installation must have Class A Ground-
electric shock, connect this connector to the grounding
Fault Circuit-Interrupters (GFCI), one for the
terminal of your electric service or supply panel with a
whirlpool system and one for the heater (if
continuous green insulated copper wire equivalent in
used).
size to the circuit conductors supplying this equipment,
This will provide additional protection against but no smaller than No. 12 AWG (3.3 mm2).
line-to-ground shock hazard.
A pressure wire connector is provided on the exterior of
Such a GFCI should be provided by the installer and the control box within this unit to permit connection of a
should be tested on a routine basis. No. 8 AWG (8.4 mm2)solid copper bonding conductor
between this unit and all other electrical equipment and
To test the GFCI, press the test button. The GFCI should exposed metal in the vicinity, as needed to comply with
interrupt power. Press the reset button. Power should be local requirements.
restored.
If the GFCI fails to operate in this manner, there is a
ground current flowing or the GFCI is defective. The
possibility of an electric shock may exist. DO NOT use
this unit. Disconnect the unit and have the problem
corrected by a qualified licensed electrician.
DO NOT operate this unit without the guard on the Use this unit only for its intended use as denoted in this
suction fitting. manual. DO NOT use attachments not recommended
by the Kohler Co.
Never drop or insert any object into any opening.
DANGER: To reduce the risk of injury, do not WARNING: For heater models, do not adjust
permit children to use this unit unless they are the heater thermostat while wet.
closely supervised at all times.
SAVE THESE INSTRUCTIONS
112130-CA (1093) 2 Kohler Co., Kohler WI
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . 2 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 11
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Materials Required . . . . . . . . . . . . . . . . . . . . . . . . . 11
ROUGHING-IN: K-1463-V-AB, K-1464-V-AB . . . . 4
Clearance Requirements . . . . . . . . . . . . . . . . . . . . 11
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 4
New or Replacement Installation Requirements 11
Required Electrical Service . . . . . . . . . . . . . . . . . . 4
Product Information . . . . . . . . . . . . . . . . . . . . . . . . 4 SITE REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Old Bath Removal. . . . . . . . . . . . . . . . . . . . . . . . . . 11
Subfloor Preparation. . . . . . . . . . . . . . . . . . . . . . . . 11
ROUGHING-IN: K-1463-H-AB, K-1463-JA-AA,
Stud Pocket Preparation . . . . . . . . . . . . . . . . . . . . 12
K-1464-H-AB, K-1464-JA-AA . . . . . . . . . . . . . . . . . . 5 Plumbing Preparation . . . . . . . . . . . . . . . . . . . . . . . 13
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 5
BEFORE INSTALLING UNIT . . . . . . . . . . . . . . . . . . 13
Required Electrical Service . . . . . . . . . . . . . . . . . . 5
Tiling-In Bead Installation. . . . . . . . . . . . . . . . . . . . 13
Product Information . . . . . . . . . . . . . . . . . . . . . . . . 5
Partially Install Bath Drain . . . . . . . . . . . . . . . . . . . 13
Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Protect Bath Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ROUGHING-IN: K-1472-V-AB, K-1474-V-AB,. . . . 6
INSTALL WHIRLPOOL . . . . . . . . . . . . . . . . . . . . . . . 14
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 6
Whirlpool Set-In. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Required Electrical Service . . . . . . . . . . . . . . . . . . 6
Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 15
Product Information . . . . . . . . . . . . . . . . . . . . . . . . 6
Secure Whirlpool . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install Plumbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ROUGHING-IN: K-1472-H-AB, K-1472-JA-AA,
INSTALL VACUUM BREAKER . . . . . . . . . . . . . . . . . 16
K-1474-H-AB, K-1474-JA-AA . . . . . . . . . . . . . . . . . . 7
FIELD WIRE ELECTRONICS . . . . . . . . . . . . . . . . . . 17
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 7
Service Requirements . . . . . . . . . . . . . . . . . . . . . . 17
Required Electrical Service . . . . . . . . . . . . . . . . . . 7
Identify Electrical Requirements . . . . . . . . . . . . . . 17
Product Information . . . . . . . . . . . . . . . . . . . . . . . . 7
Locate Field Wiring Compartments . . . . . . . . . . . 17
Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connect Control Box - 120V, 60 Hz . . . . . . . . . . . 18
ROUGHING-IN: K-1482-H-AB, K-1482-JA-AA, Connect Control Box - 230V, 50 Hz . . . . . . . . . . . 18
K-1484-H-AB, K-1484-JA-AA . . . . . . . . . . . . . . . . . . 8 Connect Heater - 60 Hz at 120V . . . . . . . . . . . . . 19
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 8 Connect Heater - 60 Hz at 240V . . . . . . . . . . . . . 19
Required Electrical Service . . . . . . . . . . . . . . . . . . 8 Connect Heater - 50 Hz at 230V . . . . . . . . . . . . . 19
Product Information . . . . . . . . . . . . . . . . . . . . . . . . 8
WATER TEST WHIRLPOOL & ELECTRONICS . . 20
Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . 8
COMPLETE FINISH WALL . . . . . . . . . . . . . . . . . . . . 20
PRODUCT NOTICES. . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALL GRIP RAILS . . . . . . . . . . . . . . . . . . . . . . . . 20
Installer Hazard Notification . . . . . . . . . . . . . . . . . 9
Factory-Assembled Features . . . . . . . . . . . . . . . . 9 COMPLETE INSTALLATION . . . . . . . . . . . . . . . . . . 20
Install Handles and Spout . . . . . . . . . . . . . . . . . . . . 20
PRODUCT REQUIREMENTS . . . . . . . . . . . . . . . . . 10
Install Whirlpool Trim Kit . . . . . . . . . . . . . . . . . . . . 20
Summary of Key Requirements . . . . . . . . . . . . . . 10
Plumbing Specifications . . . . . . . . . . . . . . . . . . . . . . 10 CLEAN-UP AFTER INSTALLATION . . . . . . . . . . . . 21
Product Inspection . . . . . . . . . . . . . . . . . . . . . . . . . 10 CONFIRM PROPER OPERATION . . . . . . . . . . . . . 22
Connections and Service Access . . . . . . . . . . . . . 10 Start-Up Whirlpool . . . . . . . . . . . . . . . . . . . . . . . . . 22
Electrical Requirements . . . . . . . . . . . . . . . . . . . . . 10 Operating Sequence. . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshoot Whirlpool System . . . . . . . . . . . . . . 23
INTRODUCTION
Please read these instructions carefully to familiarize The variety of installations possible with this whirlpool
yourself with the required tools, materials, and may require framing procedures other than those
installation sequences. Follow the sections that pertain described in this manual.
to your particular installation. This will aid you in avoiding
All information in this manual is based on the latest
the unnecessary expense associated with improper
product information available at the time of publication.
installation. In addition to proper installation, read all
Kohler Co. reserves the right to make changes in
operating and safety instructions.
product characteristics, packaging, or availability at any
time without notice.
Identify and record below the model and serial number (found at the pump end of the whirlpool):
Model No. Serial No. Date of Manufacture
Kohler Co., Kohler WI 3 112130-CA (1093)
1. ROUGHING-IN: K-1463-V-AB, K-1464-V-AB
A. ORDERING INFORMATION B. REQUIRED ELECTRICAL SERVICE
Dedicated circuits required, protected with Class A
Factory installed components include pump, control with
Ground-Fault Circuit-Interrupter (GFCI):
water level control, and piezoic switch.
Pump/control 120 V., 15 A, 60 Hz
Accessories/hardware:
Pump on left K-1463-V- shown C. PRODUCT INFORMATION
AB
Fixture: basin area top area weight
Pump on left (copper har- K-1463-K-AB
Bathing well 48” x 29” 66” x 36” 160 lbs.
ness)
water depth capacity
Pump on right K-1464-V- not shown
AB To overflow 18” 118 gals.
Pump on right K-1464-V-AB
Pump, 2-speed: high low V Hz A
Jet trim kit K-9696 required
60 Hz 1 hp 1/8 hp 120 60 12
Faucet trim kit K-9587 required
D. INSTALLATION NOTES
K-9589
K-9599 Refer to installation instructions included with fixture before
Grip rail kit K-9596 required beginning installation.
Vinyl tiling-in bead* K-1179 optional
*Use K-1179 vinyl bead when wall material contacts
any top surface of bath.
ROUGHING-IN NOTES
Fixture dimensions are nominal and conform to toler-
ances in ANSI Standard Z124.1.
No change in measurements if connected with drain
illustrated.
PUMP
Cut-out 70-1/2” x 40”
CONTROL BOX
Minimum access:
Pump/control box 20” W x 15” H panel required
11-1/2”
4-1/4”
PUMP/CONTROL ACCESS 2-1/2”
36”
1/2” I.P.S. TO VACUUM BREAKER 1/2” I.P.S. COLD 72” 7-3/8” 5-5/8”
42” 3-1/2” 1/2” I.P.S. HOT
3/4”
1/2” I.P.S. 3-7/8”
TO
1” SHOWER
24”
2-9/16” WHEN
SPECIFIED
3/4”
YOKE DETAIL 2-7/8” 1-1/2” I.P.S. THR’D 1”
2-9/16”
1/2” PIPING TO FILL SPOUT 3” 1-1/2” O.D.
1.25>132
FROM VACUUM BREAKER
112130-CA (1093) 4 Kohler Co., Kohler WI
2. ROUGHING-IN: K-1463-H-AB, K-1463-JA-AA, K-1464-H-AB, K-1464-JA-AA
A. ORDERING INFORMATION B. REQUIRED ELECTRICAL SERVICE
Dedicated circuits required, protected with Class A
Factory installed components include pump, heater,
Ground-Fault Circuit-Interrupter (60 Hz) or ELCB (50
control with water level control, and piezoic switch.
Hz):
Applicable product:
Pump/control 120 V., 15 A, 60 Hz
Pump on left K-1463-H- shown or 230 V., 15 A, 50 Hz
AB
Heater (60 Hz) 15 A, 1.5 kW at 120 V.
Pump on right K-1464-H- not shown or 30 A, 6.0 kW at 240 V.
AB
Heater (50 Hz) 30 A, 5.5 kW at 230 V.
Accessories/hardware:
C. PRODUCT INFORMATION
Jet trim kit K-9696 required
Fixture: basin area top area weight
Grip rail kit K-9596 required
Bathing well 48” x 29” 66” x 36” 175 lbs.
Faucet trim kit K-9587 required
water depth capacity
K-9589
To overflow 18” 118 gals.
K-9599
Vinyl tiling-in bead* K-1179 optional Pump, 2-speed: high low V Hz A
60 Hz 1 hp 1/8 hp 120 60 12
*Use K-1179 vinyl bead when wall material contacts
any top surface of bath. 50 Hz 1 hp 1/8 hp 230 50 5.5
D. INSTALLATION NOTES
Refer to installation instructions included with fixture before
beginning installation.
ROUGHING-IN NOTES
PUMP/CONTROL ACCESS
Fixture dimensions are nominal and conform to toler-
HEATER ACCESS
ances in ANSI Standard Z124.1.
No change in measurements if connected with drain
illustrated.
Cut-out 70-1/2 x 40” HEATER
PUMP
Minimum access:
CONTROL BOX
Pump/control box 30” W x 15” H panel required
Heater 20” W x 15” H panel recom-
11-1/2”
mended
4-1/4”
Heater service 16” clearance required
2-1/2”
36” 72”
1/2” I.P.S. TO VACUUM BREAKER
42” 1/2” I.P.S. COLD 5-5/8” 7-3/8”
3/4”
1/2” I.P.S. TO 3-7/8”
SHOWER
1” 3-1/2”
WHEN 1/2” I.P.S.
2-9/16” SPECIFIED 24” HOT
YOKE DETAIL
1/2” PIPING TO FILL SPOUT 2-7/8” 1-1/2” I.P.S. THR’D 3/4” 1” PUMP/CONTROL
FROM VACUUM BREAKER 3” 1-1/2” O.D. 2-9/16” ACCESS 1.25>132
Kohler Co., Kohler WI 5 112130-CA (1093)
3. ROUGHING-IN: K-1472-V-AB, K-1474-V-AB
A. ORDERING INFORMATION B. REQUIRED ELECTRICAL SERVICE
Dedicated circuits required, protected with Class A
Factory installed components include pump, control with
Ground-Fault Circuit-Interrupter (GFCI):
water level control, and piezoic switch.
Pump/control 120 V., 15 A, 60 Hz
Applicable product:
Pump on left K-1472-V- shown C. PRODUCT INFORMATION
AB
Fixture: basin area top area weight
Pump on right K-1474-V- not shown
AB Bathing well 48” x 30” 62” x 36” 160 lbs.
Accessories/hardware: water depth capacity
Jet trim kit K-9696 required
To overflow 15” 96 gals.
Faucet trim kit K-9587 reqquired
Pump, 2-speed: high low V Hz A
K-9589
60 Hz 1 hp 1/8 hp 120 60 12
K-9599
Grip rail kit K-9596 recom- D. INSTALLATION NOTES
mended
Vinyl tiling-in bead* K-1179 optional Refer to installation instructions included with fixture before
beginning installation.
* Use K-1179 vinyl bead when wall material contacts
any top surface of bath.
ROUGHING-IN NOTES
Fixture dimensions are nominal and conform to toler-
ances in ANSI Standard Z124.1.
No change in measurements if connected with drain
illustrated.
Cut-out 70-1/2” x 40”
Minimum access:
Pump/control box 20” W x 15” H panel required PUMP
CONTROL
BOX
11-1/2”
2-1/2” 4-1/4”
36”
72”
1/2” I.P.S. TO PUMP/CONTROL 7-3/8”
ACCESS
VACUUM 1/2” I.P.S.
BREAKER 41-5/8” COLD 5-5/8”
2-3/4” 1/2” I.P.S. HOT
3-1/2” 3-7/8”
1” 3/4”
2-9/16”
21”
1/2” I.P.S. TO SHOWER
WHEN SPECIFIED
1/2” PIPING TO FILL SPOUT 2-7/8” 3” 3/4” 1”
FROM VACUUM BREAKER
132 YOKE DETAIL 1-1/2” O.D. 1-1/2” I.P.S. THR’D. 2-9/16”
112130-CA (1093) 6 Kohler Co., Kohler WI
4. ROUGHING-IN: K-1472-H-AB, K-1472-JA-AA, K-1474-H-AB, K-1474-JA-AA
A. ORDERING INFORMATION B. REQUIRED ELECTRICAL SERVICE
Dedicated circuits required, protected with Class A
Factory installed components include pump, heater,
Ground-Fault Circuit-Interrupter (60 Hz) or ELCB (50
control with water level control, and piezoic switch.
Hz):
Accessories/hardware:
Pump/control 120 V., 15 A, 60 Hz
Pump on left K-1472-H- shown or 230 V., 15 A, 50 Hz
AB
Heater (60 Hz) 15 A, 1.5 kW at 120 V.
Pump on right K-1474-H- not shown or 30 A, 6.0 kW at 240 V.
AB
Heater (50 Hz) 30 A, 5.5 kW at 230 V.
Jet trim kit K-9696 required
C. PRODUCT INFORMATION
Faucet trim kit K-9587 required
Fixture: basin area top area weight
K-9589
Bathing well 48” x 30” 62” x 36” 170 lbs.
K-9599
water depth capacity
Grip rail kit K-9596 required
To overflow 15” 96 gals.
Vinyl tiling-in bead K-1179 optional
Pump, 2-speed: high low V Hz A
*Use K-1179 vinyl bead when wall material contacts
any top surface of bath. 60 Hz 1 hp 1/8 hp 120 60 12
50 Hz 1 hp 1/8 hp 230 50 5.5
D. INSTALLATION NOTES
Refer to installation instructions included with fixture before
beginning installation.
ROUGHING-IN NOTES
Fixture dimensions are nominal and conform to toler-
ances in ANSI Standard Z124.1. HEATER ACCESS
No change in measurements if connected with drain
illustrated.
HEATER
Cut-out 70-1/2” x 40”
PUMP
CONTROL BOX
Minimum access:
Pump/control box 30” W x 15” H panel required
11-1/2”
Heater 20” W x 15” H panel recom-
2-1/2” 4-1/4”
mended 36”
Heater service 16” clearance required 72”
7-3/8”
PUMP/CONTROL ACCESS 1/2” I.P.S.
5-5/8”
41-5/8”
2-3/4” COLD 1/2” I.P.S. HOT
1/2” I.P.S. TO
3-7/8”
1” VACUUM BREAKER 3-1/2” 3/4”
2-9/16” 21”
1/2” I.P.S. TO
SHOWER WHEN
YOKE DETAIL SPECIFIED 2-7/8” 3” 1-1/2” I.P.S. THR’D. 3/4” 1”
1/2” PIPING TO FILL SPOUT
1-1/2” O.D. 2-9/16” 1.15>132
FROM VACUUM BREAKER
Kohler Co., Kohler WI 7 112130-CA (1093)
5. ROUGHING-IN: K-1482-H-AB, K-1482-JA-AA, K-1484-H-AB, K-1484-JA-AA
A. ORDERING INFORMATION B. REQUIRED ELECTRICAL SERVICE
Dedicated circuits required, protected with Class A
Factory installed components include pump, heater,
Ground-Fault Circuit-Interrupter (60 Hz) or ELCB (50
control with water level control, and piezoic switch.
Hz):
Accessories/hardware:
Pump/control 120 V., 15 A, 60 Hz
Pump on left K-1482-H- shown or 230 V., 15 A, 50 Hz
AB
Heater (60 Hz) 15 A, 1.5 kW at 120 V.
Pump on right K-1484-H- not shown or 30 A, 6.0 kW at 240 V.
AB
Heater (50 Hz) 30 A, 5.5 kW at 230 V.
Jet trim kit K-9696 required
C. PRODUCT INFORMATION
Faucet trim kit K-9587 required
K-9589 Fixture: basin area top area weight
K-9599
Bathing well 41” x 29” 56” x 36” 140 lbs.
Grip rail kit K-9596 recom-
water depth capacity
mended
To overflow 15” 85 gals.
Vinyl tiling-in bead* K-1179 optional
*Use K-1179 vinyl bead when wall material contacts Pump, 2-speed: high low V Hz A
any top surface of bath
60 Hz 1 hp 1/8 hp 120 60 12
50 Hz 1 hp 1/8 hp 230 50 5.5
D. INSTALLATION NOTES
Refer to installation instructions included with fixture before
beginning installation.
ROUGHING-IN NOTES
Fixture dimensions are nominal and conform to toler-
ances in ANSI Standard Z124.1. HEATER ACCESS
NOTE: Heater and power panel extend 1/2” beyond the
bath rim. Provisions may be made in the framing to pro-
vide additional clearance around heater and power
panel.
HEATER
Cut-out 58” x 40” CONTROL
BOX PUMP
Minimum access:
PUMP/
Pump/control box 30” W x 15” H panel required
CONTROL
Heater 20” W x 15” H panel recom- ACCESS
mended 11-1/2”
Heater service 16” clearance required
29-3/4” 2-1/2” 4-1/4”
1T/O2” I.P.S. 41-5/8” 1/2” I.P.S. COLD 59-1/52-”5/8” 7-3/8” 1/2” I.P.S. HOT
3/4”
VACUUM
BREAKER
3-1/2” 3-7/8”
1/2” I.P.S. TO
1” 21”
SHOWER WHEN
2-9/16” SPECIFIED
YOKE DETAIL 3/4”
1/2” PIPING TO FILL SPOUT 2-7/8” 3” 1-1/2” I.P.S. THR’D 2-9/16” 1”
FROM VACUUM BREAKER 1-1/2” O.D. 1.25>132
112130-CA (1093) 8 Kohler Co., Kohler WI
6. PRODUCT NOTICES
A. INSTALLER HAZARD NOTIFICATION B. FACTORY-ASSEMBLED FEATURES
DANGER: Risk of fire, electric shock, or injury K-1463-V, K-1464-V, K-1472-V, K-1474-V: Factory
to persons. Read important safety instructions on installed components include pump, control, piezo
inside front cover of these instructions. switch, and water level control.
WARNING: Risk of electrical shock. A licensed
K-1463-H, K-1463-JA, K-1464-H, K-1464-JA,
electrician should make all electrical connections.
K-1472-H, K-1472-JA, K-1474-H, K-1474-JA,
WARNING: Risk of electrical shock. Connect K-1482-H, K-1482-JA, K-1484-H, K-1484-JA: Factory
only to a circuit protected by a Ground-Fault installed components include pump, heater, control,
Circuit-Interrupter (GFCI). piezo switch, and water level control.
WARNING: Risk of electrical shock.
The automatic timer has been factory installed to the
Disconnect power before servicing.
whirlpool system. No installation is needed.
WARNING: Risk of injury or property damage.
Please read all instructions thoroughly before The whirlpool pump and piping are factory-assembled.
beginning installation, including the following
Product Requirements.
WARNING: Unauthorized modification may
NOTICE: Follow all local plumbing and electrical
cause unsafe operation and poor performance
codes.
of the whirlpool. Do not relocate the whirlpool
pump or make other modifications to the whirlpool
system, as this could adversely affect the
performance and safe operation of the whirlpool.
Kohler Co. shall not be liable under its warranty or
otherwise for personal injury or damage caused by
any such unauthorized modification.
The optional heater, when wired with 120V/15A, will
maintain the water temperature. When wired with 240
V/30A, the water temperature can be raised several
degrees Fahrenheit in a 20-minute cycle. This
temperature rise is based on laboratory conditions.
Actual temperatures may vary in your installation. The
maximum temperature limit is 104 degrees Fahrenheit.
Kohler Co., Kohler WI 9 112130-CA (1093)
7. PRODUCT REQUIREMENTS
A. SUMMARY OF KEY REQUIREMENTS B. PLUMBING SPECIFICATIONS
(cid:3) Install unit to level subfloor.
If using a rim mounted bath faucet, flexible connections
(cid:3) Provide properly dimensioned framing. between the valves and spout may be required. Confirm
adequate mounting and connection space of specified
(cid:3) Bath can be installed in a corner. Recess, penin-
faucet for your installation.
sular or sunken installation is also possible.
Confirm adequate support for faucet; large faucets that
may be inadvertently used as a means of support are not
appropriate or safe for this installation.
C. PRODUCT INSPECTION D. CONNECTIONS AND SERVICE ACCESS
Carefully uncrate and inspect your product for damage. Before installation, ensure proper access to the final
Leave all materials in carton during construction to connections.
prevent damage.
NOTICE: Provide unrestricted service access to
NOTICE: Make sure both connections to the the pump and heater. One access panel is required for
whirlpool pump are securely tightened. servicing the pump and heater. Kohler Co. recommends
an additional access panel (see Roughing-In section
beginning on page 4 for recommended locations) when
installing a whirlpool with a heater. For future heater
servicing, provide a 16” minimum horizontal draw for
removal of the heating element.
E. ELECTRICAL REQUIREMENTS
K-1463-V-AB, K-1464-V-AB, K-1472-V-AB,
K-1474-V-AB: A Class A Ground-Fault
Circuit-Interrupter (GFCI) is required. The GFCI
protects against line-to-ground shock hazard. A 120V,
15A, 60 Hz dedicated circuit is required.
K-1463-H-AB, K-1464-H-AB, K-1472-H-AB,
K-1474-H-AB, K-1482-H-AB, K-1484-H-AB: Two Class
A Ground-Fault Circuit-Interrupters are required. One is
required for the whirlpool system and one is required for
the heater. The GFCI protects against line-to-ground
shock hazard. Use a 240V/30A (for 6.0 kW) or
120V/15A (for 1.5 kW) dedicated service for the heater.
Use a 120V/15A dedicated service for the whirlpool.
K-1463-JA-AA, K-1464-JA-AA, K-1472-JA-AA,
K-1474-JA-AA, K-1482-JA-AA, K-1484-JA-AA: Two
Earth Leakage Circuit Breakers (ELCB) are required.
One is required for the whirlpool system and one is
required for the heater. The ELCB protects against
line-to-ground shock hazard. Use a 230V/15A
dedicated service for the whirlpool. Use a 230V/30A
dedicated service for the heater.
112130-CA (1093) 10 Kohler Co., Kohler WI