Table Of Content

इंटरनेट मानक Disclosure to Promote the Right To Information Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public. “जान1 का अ+धकार, जी1 का अ+धकार” “प0रा1 को छोड न’ 5 तरफ” Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru “The Right to Information, The Right to Live” “Step Out From the Old to the New” IS 208 (1996): Door Handles -Specification [CED 15: Builder Hardware] “!ान $ एक न’ भारत का +नम-ण” Satyanarayan Gangaram Pitroda ““IInnvveenntt aa NNeeww IInnddiiaa UUssiinngg KKnnoowwlleeddggee”” “!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता हहहहै””ै” Bhartṛhari—Nītiśatakam “Knowledge is such a treasure which cannot be stolen” IS 208: 1996 lll7 mTfQ "Q(q - ~ cFi FftfHUT ) ( q/i/C/( Indian Standard DOOR HANDLES - SPECIFICATION ( Fifth Revision) (FirstReprintSEPTEMBER 1999) tcs 91.060.50 © BIS 1996 BUREAU OF INDIAN STANDARDS MANAK BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI 110002 October 1996 PriceGroup 3 AMENDMENT NO. 1 APRIL 2001 TO IS 208: 1996 DOOR HANDLES - SPECIFICATION (FifthRevision) (Page4, Table2B,Note)- Substitutethefollowing fortheexistingNote: 'NOTE- InFig.1to4thedistanceofoutercircleofthescrewholefromedgeofplateshallbe minimum4mm.' (CED15) ReprographyUnit,BIS,NewDelhi,India AMENDMENT NO. 2 'JANUARY 2003 TO IS 208:1996 DOOR HANDLES - SPECIFICATION (Fifth Revision) (Page I,clause7.1.lilies 12and2\ )- Deletethewords 'orasrequiredby thepurchaser'. (CEO 15) ReprographyUnit,BlS.NewDelhi.India AMENDMENT NO.4 MARCH 2008 TO IS 208: 1996 DOOR HANDLES - SPECIFICATION ( Fifth Revision) (Page 4, Table 28, colll)- Delete 'When aContinuous Plate isUsed'. (Page 3, Fig. 4) - Substitutethe following figure forthe existing: I /~--------------. ui -, I ~/ ~ FIXING ARRANGEMENT~ ~~ o ~i :: L II II II II II II 11111 11111 11111 11111 0r I Wi. JLl.Jl. I I I B II'-------------A------------ r (9 L~---~ NOTE- MSx20mmGIcountersunkmachinescreworanyothersuitablefixingarrangement maybeused. Fig.4 TYPICALDOORHANDLE(TYPE4) (CED 15) ReprographyUnit,SIS,NewDelhi,India AMENDMENT NO.5 NOVEMBER 2009 TO IS 208: 1996DOOR HANDLES - SPECIFICATION (Fifth Revision) (Page I, clause 4.1, last line) - Substitute 'Type 4 Mild steel, brass or aluminiumalloy'for 'Type 4Brassoraluminiumalloy'. (Page I, Table I)- Addthefollowing intheend: SINo, Material ConformingtoIndianStandard (I) (2) (3) 'ix) Mildsteelbar GradeE165(Fe290)ofIS2062:2006' (Page 5,AnnexA)- Insertthe following,asappropriate: '2062 :2006 Hotrolled low,mediumandhightensilestructural steel(sixth revision)' (CEDI5) ReprographyUnit, SIS,New Delhi,India Builders HardwareSectionalCommittee,CED 15 FOREWORD This Indian Standard (Fifth Revision) wasadopted bythe Bureau of Indian Standards, after the draft finalized bythe Builders Hardware Sectional Committeehad been approved bythe CivilEngineering Division Council. This standardwasfirst publishedin 1950and revisedsubsequentlyin 1965,1972,1979and 1987. The presentrevision hasbeenundertakento incorporatethe necessarymodificationasaresultofexperience gained duringthe useofthisstandard. Inthis revision apartfrom generalupdationofthe crossreferred standards,some dimensionshavebeenchanged and sampling clause hasbeenmodified. The compositionofthetechnicalcommitteeresponsibleforthe forniulationof this standardisgivenat AnnexC. Forthepurposeofdecidingwhetheraparticularrequirementofthisstandardiscompliedwith,the final value,observed orcalculated,expressingthe resultofatestoranalysis,shallberoundedoffinaccordance with IS 2 : 1960'Rules for rounding off numerical values (revised)'. The number of significant places retainedintheroundedoffvalue shouldbethesame asthatofthe specifiedvalue inthis standard.