installation & programming manual ness d8x / d16x alarm control panel

88 Pages·2013·2.79 MB·English

Automation Ness iComms/aComms
compatible
ness D8x / D16x alarm Control panel
Available with Navigator, Saturn or KPX keypad options
InstallatIon & programmIng manUal
7.8.1
Revision
Innovative Electronic Solutions
www.nesscorporation.com
NSW Ph 02 8825 9222 VIC Ph 03 9875 6400 QLD Ph 07 3399 4910 WA Ph 08 9328 2511 SA Ph 08 8152 0000
[email protected] [email protected] [email protected] [email protected] [email protected]
N55
D8X/D16X INStALLER MANuAL
REV 7.8.1 January 2013
Document Part No: 890-007
For use with Ness D8x/D16x control panels V5.0 and later.
WArNINgS & NotICeS
Ness Corporation manufacturing processes are accredited to ISO9001 quality standards and all possible care and diligence has been
applied during manufacture to ensure the reliable operation of this product. However there are various external factors that may impede
or restrict the operation of this product in accordance with the product’s specification.
these factors include, but are not limited to:
1. Erratic or reduced radio range (if radio accessories are installed). Ness radio products are sophisticated low power devices, however
the presence of in-band radio signals, high power transmissions or interference caused by electrical appliances such as Mains
Inverters, Wireless Routers, Cordless Phones, Computers, tVs and other electronic devices may reduce radio range performance.
While such occurrences are unusual, they are possible. In this case it may be necessary to either increase the physical separation
between the Ness receiver and other devices or if possible change the radio frequency or channel of the other devices.
2. unauthorised tampering, physical damage, electrical interruptions such as mains failure, electrical spikes or lightning.
3. Solar power inverters are a known source of electrical interference. Please ensure that this product and all associated cabling is
installed at least 3 metres away from a solar power inverter and its cabling.
WArNINg: Installation and maintenance to be performed only by qualified service personnel.
CAUtIoN: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries in accordance with local regulations.
ADSL NotICe: ADSL broadband data can interfere with the operation of your alarm dialler. It is recommended that a quality ADSL filter
be installed as per the filter manufacturer's guidelines in premises with an alarm dialler installed.
All rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Ness.
Ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing
product development and improvement.
© 2013 Ness Corporation Pty Ltd ABN 28 069 984 372
CoNteNtS
PRODuCt FEAtuRES ..................................................4 SpeCIAL FUNCtIoNS
NessComms Features ..................................................5 Send test report ..........................................................12
Installation notes ...........................................................6 Siren test .....................................................................12
Inputs and outputs ........................................................7 Panel reset ..................................................................12
Display software version .............................................12
CONNECtION DIAgRAM .........................................8–9
Keypad ........................................................................10 FACtory DeFAULtS
Clear Radio Devices ....................................................53
operAtIoN Clear Memory ..............................................................53
Operation Summary ...................................................11 Clear Panel Options ....................................................53
Clear user Codes ........................................................53
HoW to progrAm
Quick start Programming ............................................12 Output Expander options......................................54–55
How to enter Program Mode ......................................13
How to program using NessPD ..................................13 AUx oUtpUtS
Aux1 output options ...............................................58-59
geNerAL optIoNS Aux2 output options ...............................................60-61
user Codes ...........................................................14, 15 Aux3 output options ...............................................62-63
timers..........................................................................16 Aux4 output options ...............................................64-65
Vibration Sensitivity .....................................................17
Zone Assignment ..................................................18, 19 Enable/Disable hardwire zones ..................................66
Definitions. Day Zones, temp Day Zones, Home Monitor KPX Keypad options ............................................66
20
End Of Line Resistor options ...............................66
Zone to Output Mapping ......................................22–23
Various Options .....................................................24–25
AUtotIme optIoNS
tamper/Keypad Panic Output Mapping .....................26
Autotime description and examples ..........................67
System Operation Shortcuts.......................................27
Realtime Clock programming ....................................68
Home mode output mapping .....................................28
Autotime programming .........................................68-69
Day mode output mapping .........................................28
Miscellaneous Options .........................................29–30
rADIo optIoNS
Zone Supervision options .....................................31–33
Signal strength test .....................................................70
Misc. options ........................................................35–37
Ness Radio Interface ...................................................70
RADIO DEVICE PROgRAMMINg ..............................71
DIALLer optIoNS
RADIO KEy PROgRAMMINg .....................................72
tELEPHONE NuMBERS ......................................38–39
Account Numbers .......................................................38
Serial Output options ...........................................73
Report zone alarms .....................................................40
Report zone restorals ..................................................40
ACCeSS CoNtroL optIoNS
Report multiple zone alarms .......................................40
PROgRAMMINg ACCESS CARDS ............................74
Account No.2 zones ....................................................40
Access Control options .........................................74–77
Report Miscellaneous alarms .....................................41
Weigand Reader wiring diagram ................................78
Report Miscellaneous Restorals .................................41
test Call options ..........................................................42
remote operAtIoN
Dialler format options ............................................43–44
Monitoring operation ...................................................79
CONtACt ID REPORtINg CODES ...........................43
Remote operation by telephone ................................80
Dialling options ...........................................................45
Area1, Area2 open/close reports ................................46
progrAmmINg optIoNS SUmmAry ............82–85
Siren Chirp, Flash options ..........................................46
Specifications and approvals......................................86
Other reports ...............................................................47
Release Notes .............................................................87
Enable test Calls .........................................................48
Installation Record ......................................................88
Mains Report Delay .....................................................48
Listen-in to dialler ........................................................48
Swinger Shutdown ......................................................49
Line Fault Monitor .......................................................49
Programming options specific to the D8x/D16x panels
Remote access options ........................................50–51
version 6 and later are marked with the symbol.
Required Rings ...........................................................52
All other programming options are valid for panels from
version 5.0 to version 5.7
No Memory Warning zones ........................................52 See page 12 for information on how to display the panel's
software version.
D8x/D16x FeAtUreS
• 8 or 16 alarm zones.
OPtIONAL PRODuCt
• Supports up to 3 keypads (Navigator, Saturn or LCD)
• 56 user codes can be programmed to operate by keypad PIN, radio key or
access card.
• Optional NESS RADIO INtERFACE for fully integrated wireless security.
• Programmable tWO AREA PARtItIONINg can split the panel into two
independent areas plus a common area.
• REAL tIME CLOCK with AutOtIME features - auto arm/disarm, auto aux
outputs, time based user control.
• 3 Door ACCESS CONtROLLER onboard with support for Weigand prox or
Ness iComms fingerprint readers.
Ness aComms
• Supports mobile control using Ness iComms/aComms iPhone/iPad and
Andriod apps and optional ethernet adapter.
• Home Mode allows partial arming, (eg, perimeter security overnight).
Ness iComms and aComms apps
for mobile control of your D8x/ 16x • Day Mode feature allows daytime monitoring of fire doors, coolrooms etc.
control panel from home, office, • Temporary Day Zone feature allows easy enabling/disabling of Day Mode.
anywhere in the world using your • Keypad Panic feature.
iPhone/iPad or Android device. • Keypad Duress feature.
• Two button arming feature.
■ ARM, DISARM
• Fire Alarm feature with different siren tones.
■ VIEW ZONE StAtuS
• Highly flexible zone to output mapping.
■ EMERgENCy ALARMS
• ONBOARD VIBRAtION SENSOR ANALySER with programmable sensitivity.
■ CONtROL tHE PANEL OutPutS
use with Nessensor™ vibration sensors.
(D8X/D16X V7.8+)
• MuLtIPLE PROgRAMMABLE EOL resistor values from 0k to 22k (2k2
Requirements:
resistors supplied).
D8x/D16x V5.6 or later (V7.8 or later
• Siren chirp and strobe flash on arming with radio key.
to operate panel outputs).
• Quiet chirps option on arm/disarm by radio key.
Optional 101-244 Ethernet adapter, • True Dynamic Battery Test actively tests the battery under load every hour
450-185 RS232 cable. and every time a keypad code is entered.
• 4 programmable auxiliary outputs.
iPhone/iPad/Smartphone not
• ENHANCED SERIAL DAtA input/output via RS232.
included.
• AutOMAtIC RESEt FuSES.
iComms is a third party product • Programmable Reset Output lockout.
which is endorsed by Ness without • 30 event memory from keypad. 80 event memory can be accessed using
tech support. NessComms™.
• Standard defaults to suit most applications.
Emergency alarms must be enabled
• Easy programming by keypad or NessComms™ software.
in the control panel to be available in
• All programming data is permanently stored in a non-volatile memory.
iComms and aComms.
• All inputs and outputs are heavily protected against lightning and high
voltage supply transients.
• Optional output expander.
DIALLER
• Full remote upload/download by PC and modem using NessComms™
software.
• View system status and arm/disarm using NessComms™.
• Remote control of outputs via telephone.
• Contact ID Format - Two 14 digit phone numbers plus one “follow me”
number.
• Audible Voice format feature.
• Phone line monitoring (activates output).
• Dialler ‘Listen in’ option for installers.
• Auto Test calls.
• Pulse or DTMF dialling.
• True dial tone detection.
• Hex programmable client codes as required by some central stations.
4
Ness D8x / D16x Control Panel – Installation Manual
Control Panel is sold separately.
FREE SOFtWARE NeSSCommS
powerful pC-based programming & operation
software
• Fast and easy installation programming
• Arm & Disarm remotely with the Virtual Keypad
• Live zone status mode
• Download system logs, including extended D8x/D16x
logs not accessible by keypad - up to 80 events
• Database stores hundreds of clients
• All relevant control panel manuals are installed with
D8X / D16X DIreCt CoNNeCt On-Site
NessComms
SERIAL • Free For Trade users
450-185 Serial extension cable
Serial cable Now the preferred programming tool for many installers,
NessComms makes control panel programming as simple
...or 101-231 Serial to
as ticking the boxes.
uSB Adapter cable
Connect to your control panels on site via modem and
landline. If your standard modem is capable of 300 baud
half duplex operation it may be suitable for use with
...OR
Nesscomms.
DIAL-Up via modem For the added convenience of on-site programming, D8x
PStN and D16x panels also allow direct connect via serial port for
Modem fast and easy access by laptop computer. the Ness 450-185
300 Baud Serial Cable is required.
half duplex
OPtIONAL PRODuCt
MiniCENtRAL Part No. 106-125
to Clipsal C-Bus
the Ness MiniCENtRAL C-Bus interface combined
with a Ness D8x or D16x control panel gives you
full two-way C-Bus control and all the features and
benefits of a powerful alarm panel.
■ Fully Clipsal approved C-Bus Enabled Product.
■ Controls up to 255 individual C-Bus lights or outputs.
D8x/D16x Control Panel Includes full dimming, On/Off and toggle commands.
V7.3 or later ■ true 2 way communications on the C-Bus network.
■ Connects directly onto C-Bus without the need for ad-
ditional hardware such as a PCI Interface.
■ Many D16X events or status changes can control mod-
ules on the C-Bus.
■ C-Bus trigger Control and Enable Control.
■ C-Bus events can control the D8x/D16x.
■ Multiple onboard SERIAL repeater ports means the D8x/
D16x panel can also connect to other serial devices while
connected to MiniCENtRAL.
OPtIONAL PRODuCt NeSS pD
portable Download tool
Part No. 106-017
Ness PD is the fast, easy and simple way to copy
programming options from one control panel to
another in the field - all without a computer.
Ness PD copies and loads data from panel to panel
using the READER header on D8x and D16x panels.
Requires D8x/D16x V7.4 or later. Not ■ Stores separate data for one D8x and one D16x.
compatible with 106-009 D16x C-Bus panel. ■ Ideal for programming service panels.
How to use the NessPD, see page 13. ■ use Ness PD to store your default programming for even
faster commissioning on site.
5
Ness D8x / D16x Control Panel – Installation Manual
INStALLAtIoN proCeDUreS
eSD WArNINg the main panel housing and keypad/s should be installed within areas that are
(Electrostatic Discharge). protected by motion sensors or reed switches. A linen closet or cupboard are good
Once properly installed, Ness control examples as these are generally located in the centre of the premises. Installing in
panels are well protected from ESD. ceiling spaces or other areas where extremes of temperature may be encountered is
However, take note of the following not advised.
precautions during installation.
Positioning of the movement detectors should be considered as the incorrect position
the human body can generate static may cause unwanted alarms. Refer to the motion sensors' installation instructions.
electricity when it is insulated from earth
1. Remove the lid and the battery from the base.
- for instance by walking over carpet.
2. Securely mount the rear panel housing in a secure location.
ESD occurs (and a small shock is
3. Run all cabling needed for the installation.
sometimes felt) if an earthed metal
object is then touched. 4. Insert the red PCB stand-offs in the housing and then plug the circuit board onto
the stand-offs. See the ESD Warning on this page.
the installer should be aware that if
he generates static electricity while 5. Wire the sensors, sirens and accessories to the main board terminal blocks as per
installing the panel and then discharges the wiring instructions shown in this installation manual.
this static electricity into the internal 6. Fit the battery into the housing but DO NOt CONNECt the battery yet.
components on the main D8/D16 circuit 7. Insert the panel tamper bracket leads as shown below.
board or the keypad board, then ESD 8. Power up as described below.
damage may occur.
9. Close the lid and program the panel as required.
the circuit board should not be
unwrapped until it is actually ready to be
installed.
poWer-Up proCeDUre
to enter INStALLER PROgRAM MODE the first time, power-up with the PROg/tAMP
Methods to avoid electrostatic build-up.
link OFF. If TthELeEP PHORNOELgEA/Dt(ASuMppPlie dl)ink is ON and any other 24hr zones are unsealed on
1. use a foot strap, a wrist strap,
power-up thCeo npneactntoeMl owdeil3l siomckmetediately go into alarm - reset the alarm via keypad or
or a grounding mat. the aim is
to connect the body to earth to remove powLeeard tsoho wsntoispfo rtAhuest raalilaaornmly..
N.OTAMPERSWITCH
discharge static before it builds up. ALTERNATIVETAMPERSWITCHWIRING
1. CoNNeCt tHe bAttery FIrSt(.7 6O1b-0s0e2)rvCeol ocuor:rBrLeAcCtK polarity.
the connection is a high resistance ForN.C.TamperSwitches
a) the heartbeat LED will flash coSnutpinpluieoduwsithlyN etoss isnirdeniccaotveer scorrect operation.
for personnel safety. N.CTAMPERSWITCH(SWI920)Colour:WHITE
2. If the above is not available, then it b) the Current Limiting globes should be OFF. If the globes are glowing, the
is advisable to wear clothing that will battery connection TisAM Preversed. Immediately disconnect the battery and check the
minimise the build-up of statDic.8MAINBOARD TpELoElPaHrOitNyE of the batte+r0y1V2 Vleads. 12VDCoutput
3. Handle circuit boards by the edges.
Avoid touching any components on If the heartbeat LED doZe8s not flash s2tek2adilyZo oner 8cycleEsN oDffO iFnLteINrmERitEteSnIStlTyO tRhSere may be a
tinh ep abrotiacrudl aars, athree ninotte gguraatreadn tceiercdu bitsy, pmroodbele mpr ewsitsh pth9e5 ein,i tpia9liCZ7s7eat i&o np o9f8 teh eto o2 ken2rbaosaZerod nae lml7 pemroogiTsrrhyfaeu. mldltyeofmpa ruorlitegnermagnmd eamodnfalbyidnl,ee riwrneeits lhIiosnataocsrhdtova aifcllaueleecoritsf op12r3kry2roe (dsg2i2ser0taof0armOvuah llmutsess.), .sTeheepErOogLrvaamlue
their manufacturers to be safe from LDIiSagTnEoNstPicINs.SConntehcteann remove power byZ 6briefly remov2ikn2g onZoen eo6f the oNbpeatsiotstnepParn1ye2 ll9seEaa.redssu pthplieedn wrieth-c2ko2n1n%etcolte.r atnhceeM etalFilmresistors.
ESD. 8Ohmhornspeahkeeratortbeat LED should nCow be flashing continuouslyC,o ploruorccoedee:dR etod, Rseted,pB l2ac.k,Brown,Brown.
45.. taaitdnoovsisso u tmcpacidholhilna saw riastmgiainobeli nksle eaie.an n wrgttyhhh aeseilr tedoba uuwtoinicblod dbjre-k ueacinpfsto g tmroo LISTENRECEIVEReof u nswct oahthtr ikecRHcoIi n,nopEe tentaCgirondEfen eaIcaVrctlefEionR.Rrgadio lisJBPt1oOewnXLeItTNorA==Ku2dMpiSTa.Pawel ElmeatiRtrlhpetHt&deoolir,nnPena ekRloisaonrN.OrmfmfGdat RosltiAtcseaMtUntaaetteLertrIeNNK th oatN t hteH bea CZZZZpt2354teLrUyg is pcAhCark2222gkkkk.i2222 ntgh ZZZZecooooo nnnnCeeeerr2453uercretlny.t(NN ZNLOOO.iCRRmN.MM)EAADitLLEWiLLnVYYIICgRCOE LPISgNOENSGloEDbeZZsoo nnCmee ay glow slightlyZZ OONNEESS11--88
on the installation. installerprogrammode C (N.O.)DEVICES C
AAUUXX21 AUX Z1 2k2 Zone1
AAUUXX43 A1-u4x.outputs 0V D8x/D161x2 VHDoCuoustpiuntfgordetectors.AutoResetfuseprotected.
+120VV TAPR +12V 500mAmax.fromall12Voutputs.
SERIAL SRREEs2RA3DIA2ELRserialport BSN(WWO.CHXI.TITCTCAEoHM)ntPaJ1EctRs MPOG KEYPAD+CDC1OAL2KMTV Rthee+CmDC OLA1lKiMT2odVv wabithle tlhide. sCclripew lesf tp srPaiodcrvoceived fisiesrsisdNoM3otE. nakSrteyxh Sfiy meoLpbCnruaoD dm sassKlerieddycpesua-.drine
READ Cupontone3cNtieosnsfor RESET OUpRt3ox21x2NVesSscr1ea2mVeSrir(e1n0(01-0203-81,7120)0-004)
E Weigandreaders
R
STR Upto2xStrobe Light(NOI-300)
“HEARTBEAT”LED
Constantlyflashes
BATTERYLEADS SIREN Upto3xHornSpeaker,8Ohm (NOI-110)
(supplied)
BATTE RBLEADC+K 1AA7CCV 1(W7VhiAteC&Black) Ness17VACPlugPackBFbiaatstct ekurupyp. t ob a1t2teVr y7 Ahho lder.
RY EARTH (Australiaonly)
EARTH
HEATSINK (Yellow/Greenstripe)
BATTERYCONNECTION
For12V7Ahbackup
battery(BAT210) OPTIONALACCESSORIESFORD8X&D16X
NessRADIOINTERFACE NessRELAYBOARD NessOUTPUTEXPANDER WEIGANDREADERINTERFACE NessSERIALCABLE
PartNo.100-200 PartNo.106-013 PartNo.106-011 PartNo.106-012 PartNo.450-185
ToREADER
TORECEIVER ToAuxHeader header ToSERIAL
HEADER NI header
6 OVBlackRSSIBlueDATAWhite+12VRedNess DpsNvTo8otouhOrlxtewiNtTkpaOA eeREuUgC/srX:tee1Ne s.ElCaDdaslcyeNbucO1cABiyeUCttXa6rso2NtibhscCaxloeresd rNctiCfOreApooiUCskrXrnoo3NetssCsvruwnoiNdmclOiAtethpUCcursXah4NasoCn4istnelrng eel.oPllealUtoc0+AAAAabVysUUUUw1tXXXX2ereV4321nicaeToAuxHeaderl – InsConnectuptoonetaadditionalexpanderllation TMU+O12VIn12345678910111213141516anual16programmableopencollectoroutputs UrcReoepanadtndoe3eer3crsatIe(ndNdtdee2rvrseifasascst1hae0e.b11leoBBGWRB-0lrlperukhnndW1ttio4en)igaclaa3nndwbaey UtosaedPfCorfodrirpercotgcrPpoaoCmnrntsmeerciinatlg
separatepowersupply.
ortwowayserialcomms.
INpUtS oUtpUtS
Monitored Zones. 12 VoLt outPut
the Ness D8x and D16x have 8 or 16 fully programmable zone A regulated 13.8 VDC output is available to power detectors
inputs. (Monitored by end of line resistor). and other equipment. this output is available from two sets of
Also, 1 x 24 hour External tAMP input. (Monitored by end of line terminals marked +12V and 0V. this output is protected by an
resistor). 1 x 24 hour Box tamper input. (Normally Closed input. Automatic Reset fuse.
Resistor is not required). A maximum load of 500mA may be connected to these terminals.
end of Line resistor
siren
Each zone input must be terminated with an end of line (EOL) resistor
the on-board siren driver will drive a maximum of 3 x 8 ohm horn
unless the zone is disabled by option P125E.
speakers (Ness Part No. NOI110 or 100-171 Internal Siren). the
the default EOL resistor value is 2.2k (2200 Ohms). the EOL value will reset at the end of siren time (P29E) or whenever the panel is
is fully programmable. Available options are 0k (closed circuit), 1k, reset, whichever comes first.
1.5k, 2.2k, 3.3k, 3.9k, 4.7k, 5.6k, 6.8k, 8.2k, 10k, 12k and 22k. See
this output is protected by an Automatic Reset fuse.
programming option P129E.
str
tAMP – tamper input
A latched 12VDC output for connecting strobe lights.
the tAMP input must also be sealed with an end of line resistor. this
this output will reset after 72 hours (3 days) or when the panel is
input is always a 24hr input. the EOL value programed by option
disarmed. (D8/D16 versions prior to V4.5 allow indefinite strobe
p129E also applies to the tAMP input.
operation, until the panel is reset).
AC inPut terMinALs
A maximum of 2 x 1 Watt Strobes (Ness Part No. NOI300) can be
these terminals are for the connection of the Ness plugpack. the
connected to this output.
Ness D8/D16 requires an AC transformer rating of 1.4 Amps @ 17V
this output is protected by an Automatic Reset fuse.
AC minimum. (Ness Part No. POW215)
reset
eArth
A 12V DC output for connecting Ness sirens, piezo sirens or
For maximum protection against damage caused by lightning strikes,
relays, etc. this output will reset at the end of siren time (P29E) or
connect a good earth to this terminal. Alternatively use the Earth lead
whenever the panel is reset, whichever comes first.
from the plug pack.
A maximum of 3 x 12V piezo screamers (Ness Part No. 100-238,
BAttery
100-004) or 2 X Ness Piezo (Part No 100-172) can be connected to
these terminals are for the connection of a sealed lead-acid
this output.
rechargeable 12Volt battery. Charge current is limited to 350mA.
the charge voltage is factory preset at 13.8V. Note: A 12 Volt sealed this output is protected by an Automatic Reset fuse.
lead acid rechargeable battery must be connected for correct panel AuX heAder
operation and to ensure the Siren, Strobe and Reset outputs operate the Aux1 to Aux4 outputs are open collector outputs (switch
correctly. negative) which can supply a maximum of 100mA. Each Aux
the panel will shut down if battery voltage is below 11V and mains output can be programmed to perform several different functions.
power is off. the header also provides a 12V DC output, max. draw 100mA.
See program options P141E to P144E.
Observe correct polarity when connecting the battery.
(Ness Part Number BAt210 12V 7Ah battery) rs232 seriAL Port
two way RS232 serial port for interfacing to a PC or external
Current LiMiting gLoBes
automation products. the serial data is 9600 baud, 8 data bits, no
the current limiting globes serve to regulate battery charging current.
parity, 1 stop bit. Developer's kit available on request.
When the battery is fully charged the globes will not glow. the
globes will glow slightly when recharging the battery after a short Prog/tAMP – Program Link & internal tamper input
power outage. If the globes glow very brightly the battery is drawing the PROg/tAMP link appears on the two pin J1 header.
excessive current and may be faulty, or the battery is connected in the PROg/tAMP link has two purposes:
reverse. Check the connections or connect a charged battery.
1. to enter Installer program mode on initial power up. Power-
up with the PROg link OFF. the PROg link (or Box tamper lead)
must be ON in operating mode.
2. box tamper. When used with the Internal tamper Lead
RED+ 12V7AhSealed (supplied), PROg/tAMP serves as the 24hr tamper input for the
LeadAcidBattery panel’s internal tamper switch.
Replace the PROg Link with the Box tamper Lead. Connect the
BLACK Internal tamper Lead spade terminals directly to the terminals of
OBSERVE the internal tamper switch (supplied). An end-of-line resistor is
CORRECTPOLARITY
NOt required on this input.
YRETTAB When PROg/tAMP is used for Internal tamper, powering up with
the panel’s cover open will enter Installer Program Mode.
CurrentLimiting
Globes SIreN LoAD. A maximum output of 2.0A continuous is
HE available from the SIREN and RESEt outputs and 200mA
A
TS from the StR output.
IN
K Recommended maximum power load:
3 x Horn speakers (SIREN output)
oUtpUt FUSINg. the 12V outputs, Siren, Reset and 2 x Strobe lights (StR output)
2 x Ness Internal Sirens (100-172) (RESEt output)
Strobe outputs are protected by Automatic Reset elec-
tronic fuses. these outputs will automatically reset once Note: (This assumes no more than 500mA is being drawn from the
the overload is removed. 12V device outputs).
7
Ness D8x / D16x Control Panel – Installation Manual
D8x CoNNeCtIoN DIAgrAm
TELEPHONELEAD(Supplied)
ConnecttoMode3socket
LeadshownisforAustraliaonly.
N.OTAMPERSWITCH
ALTERNATIVETAMPERSWITCHWIRING
(761-002)Colour:BLACK
ForN.C.TamperSwitches
SuppliedwithNesssirencovers
N.CTAMPERSWITCH(SWI920)Colour:WHITE
TAMP
0V
TELEPHONE 12VDCoutput
D8MAINBOARD +12V
Z8 2k2 Zone8 ENDOFLINERESISTORS
C Thedefaultendoflineresistorvalueis2k2(2200Ohms).TheEOLvalue
2k2 Zone7 isfullyprogrammablewithachoiceof13resistorvalues,seeprogram
Z7
LISTENPINS optionP129E.
Diagnostics.Connectan Z6 2k2 Zone6 Nesspanelsaresuppliedwith2k21%toleranceMetalFilmresistors.
8Ohmhornspeakerto C Colourcode:Red,Red,Black,Brown,Brown.
LIS listentodiallertones. Z5 2k2 Zone5
TE ZONEWIRING ZONES1-8
N Z4
J1LINK 2k2 Zone4 NORMALLYCLOSED Zone
RECEIVER RHcoInopEetentaCirondEfeneaIcaVrctlefEionR.Rrgadio PBoOwXeTrA==uMpTSPaweEmaiRtlhpe&delir,nPnakRloaorOrmfmfGatRoslAtseaMtntaetteeLrINK CZZ23 22kk22 ZZoonnee23 N(NO.CR.M)ADLELVYICOEPSEN ZonCe ZONES1-8
installerprogrammode C (N.O.)DEVICES C
AAUUXX21 AUX Z1 2k2 Zone1
AAUUXX43 A1-u4x.outputs 0V 12VDCoutputfordetectors. Maximum 3 keypads per system.
+102VV J TAMPPROG +1D2AVT 500mAAmuatox.Rfreosmetafulls1e2pVrootuetcptuetds..
1
SERIAL SREs2R3IA2Lserialport BSNWO.CXI.TTCCAoHMntPaEctRs KEYPADCCOLKM +CDCOLA1KMT2T V (((WBB (llRauheceitkde))))
READER (WHITE) +12V navigator keypad*Saturn keypad KPX keypad
READ CuWpoentigonae3ncdtNioernesasfdoerrs. RESET UOpRt3ox21x2NVesSscr1ea2mVeSrir(e1n0(01-0203-81,7120)0-004)
E
R Also used for Ness PD
Portable Download tool. STR Upto2xStrobe Light(NOI-300)
“HEARTBEAT”LED
Constantlyflashes
BATTERYLEADS SIREN Upto3xHornSpeaker,8Ohm(NOI-110)
(supplied)
BA BLACK 1A7CV
TTE RED+ AC 1(W7VhiAteC&Black) Ness17VACPlugPack *navigator keypad is compatible
RY EARTH (Australiaonly) with D8x/D16x control panels
EARTH version 7.0 or later
HEATSINK (Yellow/Greenstripe)
BATTERYCONNECTION
For12V7Ahbackup
battery(BAT210)
Optional Accessories for D8x & D16x AuX header
AuX header
RECEIVER #the Weigand Interface and Ness PD SERIAL
header bheoathd ecro. nWneeicgta tnod th Ine tRerEfaAcDeE mR ay be RhEeAaDdEeRr# header NI
temporarily disconnected to use the TUO
Ness PD. +12VIn
OVBlackRSSIBlueDATAWhite+12VRed 3 2 1BBGWRBlrlerukhnndt RhEeAaDdEeRr# DOWNLOADPORTABLED8X / D16X 106-017NESS PD PCp Soertrial 0V+12VAUX4AUX3AUX2AUX1NOCNCNOCNCNOCNCNOCNCAUX1AUX2AUX3AUX4 Connectuptooneadditionalexpander 12345678910111213141516
100-200 106-012 Weigand 106-017 Ness pD 450-185 106-013 relay board. 106-011 output expander.
Ness radio Interface. Interface. portable Download Serial Cable. Provides 4 relay Provides 16 programmable
Provides connection tool. Allows easy used for two-way outputs suitable for open collector outputs.
for up to 3 addressable on-site copying and serial comms or switching low voltage See page 54.
Weigand Readers (Ness re-loading of D8x/ direct connect to accessories.
101-014). D16x programming a PC.
See page 78. options without a PC. the Relay Board and the Output Expander Board connect to
the Aux header on the D8x/D16x main board but you cannot
Requires D8x/D16x connect both at the same time. If required, the Relay Board
version 7.4 or later. can be driven by outputs from the Output Expander.
8
Ness D8x / D16x Control Panel – Installation Manual
D16x CoNNeCtIoN DIAgrAm
TELEPHONELEAD(Supplied)
ConnecttoMode3socket
LeadshownisforAustraliaonly.
N.OTAMPERSWITCH
ALTERNATIVETAMPERSWITCHWIRING
(761-002)Colour:BLACK
ForN.C.TamperSwitches
SuppliedwithNesssirencovers
D16MAINBOARD N.CTAMPERSWITCH(SWI920)Colour:WHITE
TELEPHONE
TAMP
0V
LISTENPINS 12VDCoutput
D8lisiOateghnnmotoshtdoicirasnl.lesCrpoetonannkeeescr.ttoan Z16C +Z182V Zone8 Z16 Zone16 ENDOFLINERESISTORS
C C
ZONES9-16 Z14Z15 ZZ76 ZZoonnee67 Z14Z15 ZZoonnee1145 TvTahhleeuedEeOisfLa2uvklat2leu(ne2d2iso0ff0ulilOnlyehpmrreoss)gi.sratomrmable
LISTEN JC1onPnRecOtGin/tTeArnMalPtaLmINpKer Z12Z13CC CZZ54 ZZoonnee45 Z12Z13C ZZoonnee1123 1wsNe%eiteshtspoarploecarghnaroneailcmcseeaoMorpefeti1stoau3nlpFrPpeil1lsmie2isd9rtoeEwsr.iitvshatol2urkse2.s,
RECEIVER RHcoInopEetentaCirondEfeneaIcaVrctleEfionR.Rrgadio ltPoPehforaefowdtgsoeoruraerpmunpleptlaieeMvwrdeoIijtndluhisenmtt.kahpeleedlerl.wrinikth Z11Z10C CZZ23 ZZoonnee23 Z11Z10C ZZoonnee1101 CRoedlo,uRrecdo,dBel:ack,Brown,Brown.
C C 12VDCoutputfordetectors.
+AAAAUUU1U20XXXXVV4231 AA1-Uu4xX.outputs 0VZ9+12V +Z01V12V Zone1 0VZ9+12V Zone9 5A0u0tomRAesmeatxf.usfreomproatlelc1t2eVd.outputs.
TAPR DAT
SERIAL SREs2R3IA2Lserialport BSNWO.CXI.TTCCAoHMntPaEctRs MPOG KEYPADCCOLKM +CDCOLA1KMT2T V (((WBB (llRauheceitkde)))) Mpearx simysutmem 3. keypads
READER (WHITE) +12V navigator keypad*Saturn keypad KPX keypad
READ CuWpoentigonae3ncdtNioernesasfdoerrs. RESET OUpRt3ox21x2NVeSscsr1ea2mVeSrir(e1n0(01-0203-81,7120)0-004)
E
R Also used for Ness PD “HEARTBEAT”LED
Portable Download tool. Constantlyflashes STR Upto2xStrobeLight(NOI-300)
BATTERYLEADS SIREN Upto3xHornSpeaker,8Ohm(NOI-110)
(supplied)
B BLACK AC
A 17V
TTE RED+ AC 1(W7VhiAteC&Black) Ness17VACPlugPack *navigator keypad is compatible
RY EARTH (Australiaonly) with D8x/D16x control panels
version 7.0 or later
EARTH
HEATSINK (Yellow/Greenstripe)
BATTERYCONNECTION
For12V7Ahbackup
battery(BAT210)
SIREN WIRING (D8 & D16) EXTERNAL INTERNAL
ALTERNATIVE 12V SIRENS:
100-172 Ness 12V Internal Siren
NESS D8/D16 N.O. TAMPER SWITCH 100-238 Top Hat 12V Piezo Screamer
CONTROL PANEL (761-002) Colour: BLACK
TAMP Ness Panel & Noise KITS
C 2K2 are supplied with the
HORN 100-238 Top Hat screamer
RESET
SPEAKER
SISRTERN RED BLACK (NOI110) BLACK RED
The terminal block should STROBE LIGHT
be mounted inside the (NOI300)
siren cover.
© 2004 ness Security Products
9
Ness D8x / D16x Control Panel – Installation Manual
KeypaD
keypAD DISpLAy INDICAtorS IN operAtINg moDe
keypAD ICoN
oFF oN FLASHINg
DISpLAy
ZoNeS
Zone is sealed. Zone is unsealed. Zone is in alarm.
1-8 (or 1-16)
Zone/s are unsealed. Ready to Arm
OK or Power fault.
or Panel is armed.
READY TO ARM
or phone line fault.
Panel is disarmed, Panel is armed,
ARMED
or Area 1 is disarmed, if or Area 1 is armed, if
using Areas. using Areas.
Area 2 is disarmed. Area 2 is armed if
ARMED
using Areas.
Home Mode is disarmed. Panel is armed in Day Mode enabled, (see
HOME
Home Mode. page 20).
Normal. Memory mode New alarm/s in memory.
selected.
MEMORY
the instructions on this page relate to
Normal. Receiving a radio A Radio Key or other
Ness Saturn and KPX keypads. signal. (If radio fitted.) radio device has low
Refer to the Ness Navigator user's battery.
manual for operating instructions specific Normal. Internal tamper: Double
to the Navigator touch Screen keypad. Flash with long pause.
External tamper: Steady
TAMPER
flash.
keypAD beepS
Normal. Zone/s are Excluded.
beepS meANINg
EXCLUDE
Any key press. Normal. the backup battery
1 BEEP
is low.
LOW
3 BEEPS Valid Command. BATTERY

Normal. Mains power is off.
–– 1 LONg BEEP Error.

MAINS
OFF
..10.. 10 BEEPS Mains Power is off
or Panel Battery is low Normal. user Program Mode. Installer Program Mode.
or A Radio Device PROG
has sent a low battery
signal Normal Dialler is on line. Phone line fault or
or telephone Line Fail LINE failure to communicate.
has been detected.
An Autotime action is
... ... ...
Constant SLOW beeps due to begin. keypAD DISpLAy INDICAtorS IN memory moDe
keypAD ICoN memory eVeNt
An Autotime action
. . .
will begin in one Zone numbers 1–8 or 1–16 Zone alarm
Constant FASt beeps
minute.
(no icons displayed) Panel Disarmed
ARMED Panel Armed (or Area 1 Armed)
DISPLAy tESt ARM2 Area 2 Armed
to display all available keypad icons MAINS Mains power failure
press and hold the button for at least BAttERy Low Battery
2 seconds. All icons will be displayed
tAMPER + 1 Internal tamper alarm
while the button is held down.
tAMPER + 2 External tamper alarm
Display test can be activated at any time
EXCLuDE + 1 Panic alarm
either in operating mode or any program
mode. EXCLuDE + 2 Medical alarm
EXCLuDE + 3 Fire alarm
NuMBER OF KEyPADS LINE telephone line fail
up to 3 LCD keypads can be connected RADIO, EXCLuDE Radio Key Panic alarm
to a panel.
RADIO, BAttERy, ZONE Radio Device battery low, (Device number is indicated by zone lights)
RADIO, BAttERy, ARM Radio Key battery low, (Radio Key number is NOt indicated)
CABLE LENgtH
RADIO, tAMPER, ZONE Radio Device tamper alarm (Device number is indicated by zone lights)
the maximum allowable cable length is
RADIO, HOME, ZONE Radio Supervision alarm (Device number is indicated by zone lights)
100m (total cable length to all keypads).
HOME, ZONE Wired Zone Supervision alarm (Zone number is indicated by zone lights)
10
Ness D8x / D16x Control Panel – Installation Manual