Installation • Operation • Care

28 Pages·2016·2.32 MB·English

Installation Operation Care
• •
Applause Honeycomb Shades
®
PowerView Motorization
™
Contents
GETTING STARTED
Product View ..........................................................................1
Tools and Fasteners Needed .................................................2
INSTALLATION
Installation Overview ............................................................3
STEP 1 — Install the Brackets ..............................................3
Mount the Installation Brackets — Inside Mount .............4
Mount the Installation Brackets — Outside Mount ..........6
Mount the Installation Brackets — End Mount .................8
STEP 2 — Install the Shade ..................................................9
STEP 3 — Connect the Power Source ................................10
OPERATION
Testing the Shade ................................................................14
Using the PowerView™ Remote ...........................................14
Resetting the Shade (If Necessary) .....................................17
Level the Bottom Rail (If Necessary) ...................................18
Troubleshooting ...................................................................19
CARE
Removing the Shade (If Necessary) ....................................21
Cleaning Procedures ............................................................21
DECLARATIONS .................................................................23
WARRANTY ...........................................................Back Cover
Questions?
Call the Hunter Douglas Customer Information Center at
1-888-501-8364.
© 2016 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or
their respective owners.
Getting Started
PRODUCT VIEW
Installation
Spacer Brackets
Block
Manual
Control
Button
Headrail
POWERVIEW™
STANDARD
BOTTOM-UP
SHADE
Bottom Rail
Not Shown: Top-Down, Top-Down/Bottom-Up, and Duolite™ Shades
Power Options (Rear View) High Mount
Battery Wand
(Standard)
18V Battery
Wand
Low Mount
Battery Wand
(Optional)
18V DC
Power Supply
(Optional)
Not Shown:
Extension
Satellite Battery Pack
Cable
C-Size Satellite Battery Wand Power
Large DC Power Supply Cable
1
Getting Started
Thank you for purchasing Hunter Douglas Applause® honeycomb shades with PowerView™
Motorization. With proper installation, operation, and care, your new shades will provide
years of beauty and performance.
Please thoroughly review this instruction booklet and the enclosed packing list before
beginning the installation. If your shade has a protective plastic cover on the fabric-covered
headrail, keep the plastic in place until the shade is installed.
TOOLS AND FASTENERS NEEDED
■ Flat blade and Phillips screwdrivers
■ Level (laser level is recommended)
■ Measuring tape and pencil
■ Power drill, 3/32" drill bit, and 1/4" hex driver
In addition, you will need fasteners designed to work with your specific mounting surface(s).
■ #6 Hex Head Screws (Provided). Two 11/2" screws are provided per installation bracket.
■ Longer #6 Hex Head Screws (Not Provided). If using spacer blocks, use #6 screws long
enough for a secure attachment.
■ #6 Flat Head Screws (Provided). If end mounting the shade, use two 11/2" screws per
installation bracket.
■ Speed Nuts and Screws (Provided). Extension brackets come with speed nuts and
screws.
■ Drywall Anchor (Not Provided). Use drywall anchors when mounting into drywall.
Speed Nut
#6 x 11/2" Longer #6 Hex Head Screw #6 Flat Head Screw and Screw
Hex Head Screw for Use with Spacer Blocks for Use with End Mounts (Two Provided with
(Provided) (Not Provided) (Provided) Each Extension Bracket)
2
Installation
INSTALLATION OVERVIEW
To install your shade, you will need to perform the following three steps:
STEP 1: Install the Brackets
STEP 2: Install the Shade
STEP 3: Connect the Power Source
STEP 1 — INSTALL THE BRACKETS Shade Brackets
Width Required
■ Your order will include the correct number of installation 12" – 36" 2
brackets for your shade width, as shown in the table.
361/8" – 72" 3
➤ For end mounts, only two brackets are used up to the 721/8" – 108" 4
maximum width of 72".
1081/8" – 144" 5
Installation End Mount 1441/8" – 174" 6
Bracket Brackets
IMPORTANT: A 1/2" spacer block is required for shades 1/2" Spacer Block
using an attached battery wand. The spacer block is
pre-attached to the back of the installation bracket.
■ Should the spacer block become detached, reattach it. 1/8" Shim
➤ Insert the legs of the installation bracket
into the tabs on the spacer block.
➤ Rotate the installation bracket back,
as shown, to snap it in place.
Tab
3
Installation
Mounting Types and Window Terminology
If the installation brackets are mounted correctly, the rest of the installation process follows
easily. To prepare for this important first step, review the mounting types and basic window
terminology illustrated below.
Head Jamb
Jamb Jamb
Collectively, the sill and
jambs are called the
Inside Mount Outside Mount
“window casement.”
Shade fits within Shade mounts outside
window opening. window opening.
Sill
■ Refer to the appropriate page below based on your order:
➤ Inside Mount — Below
➤ Outside Mount — Page 6
➤ End Mount — Page 8
MOUNT THE INSTALLATION BRACKETS — INSIDE MOUNT
■ Mark 2" in from each jamb for bracket location.
➤ If more than two installation brackets came with your order, space additional bracket(s)
evenly between the two end brackets. Allow a minimum of 15" between the
brackets at the motor end for the battery wand. Mount into wood whenever
possible.
Minimum of 15" for Battery Wand
2" Space Evenly Space Evenly 2"
Jamb Jamb
■ Center the brackets on your marks, then mark each of the screw holes.
➤ Mounting depths vary depending on the power option. See the chart on the next page
for minimum and fully recessed depth requirements.
➤ Mark both winged screw holes with shallow mounting depths.
➤ Mark the center screw hole when depth permits.
4
Installation
Mounting Depth Requirements
Minimum Minimum Minimum
Mounting Depth Mounting Depth Fully Recessed
Power Option Inside Mount End Mount Mounting Depth
High Mount
Battery Wand 1" 13/4" 23/4"
Low Mount
Battery Wand 1" 13/4" 25/8"
All Other
Power Options 1/2" 11/4" 21/4"

See
Use Center Hole
Chart
When Depth Permits
■ Drill the screw holes using a 3/32" drill bit.
CAUTION: Use drywall anchors when mounting into drywall.
■ Use a level to check that the mounting surface is level. Shim the brackets if necessary.
■ Attach the installation brackets using the screws provided.
IMPORTANT: The front edges of the installation brackets must be level and aligned. If
mounting to a heavily textured surface, shim the brackets, if needed.
Proceed to “STEP 2 — Install the Shade” on page 9.
5
Installation
MOUNT THE INSTALLATION BRACKETS — OUTSIDE MOUNT
■ Center the headrail over the window opening at the desired height. Use a pencil to lightly
mark the wall at each end of the headrail.
➤ Alternatively, measure the width of the headrail and use that width to mark the
headrail end points over the window opening.
■ Mark 2" from each end of the headrail.
➤ If more than two installation brackets came with your order, space them evenly
between the two end brackets and mark their location. Allow a minimum of 15"
between the brackets at the motor end for the battery wand. Mount into wood
whenever possible.
Headrail End Marks
Minimum of 15" for Battery Wand
2" Space Evenly Space Evenly 2"
Window Opening
■ Center the brackets on your marks, then mark each of the screw holes.
➤ A minimum of 11/4" flat vertical surface is required to mount the brackets.
➤ The top of the installation brackets or extension brackets should be at the desired
shade height. The brackets should be level and aligned.
➤ When using extension brackets, mark two screw holes per bracket.
CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not
mount brackets on curved molding.
■ Drill the screw holes using a 3/32" drill bit.
CAUTION: Use drywall anchors when mounting into drywall.
6
Installation
■ Attach the installation or extension brackets using the screws provided.
IMPORTANT: The front edges of the installation brackets must be level and aligned to
each other.
■ If using spacer blocks for added clearance, the spacer blocks
and shims may be stacked.
➤ A maximum of 11/2" of added clearance using spacer blocks
and shims is recommended.
■ Attach the spacer blocks and installation brackets to Maximum
a flat vertical mounting surface with #6 mounting 11/2"
Longer Screw
screws long enough for a secure installation. (Not Provided)
➤ The top of the spacer blocks should be at the
desired shade height.
IMPORTANT: The front edges of the installation
brackets must be level and aligned to each other.
CAUTION: Use drywall anchors when mounting
into drywall.
■ If using extension brackets, attach an installation
bracket to the underside of each extension bracket
using the provided screws and speed nuts.
Proceed to “STEP 2 — Install the Shade” on page 9.
7
Installation
MOUNT THE INSTALLATION BRACKETS — END MOUNT
11/4"
End mount the headrail when conventional mounting techniques will not Mwionrimk u—m for example,
in an arched window opening.
■ Position the end mount brackets so that the top of
the attached installation brackets is at the ordered
Ordered
height of the shade. Shade
11/4" Height
CAUTION: Both brackets must be installed at the Minimum
same depth and height.
■ Mark both screw holes.
➤ The mounting surface must be vertical and flat, Ordered
Shade
not part of an arched curve. Height
➤ Minimum mounting depth is 11/4". Minimum
mounting depth for a fully recessed end mount
is 23/8".
■ Drill the holes using a 3/32" drill bit.
■ Attach the end mount installation brackets
using the flat head screws provided.
IMPORTANT: Drywall mounting is not
recommended.
IMPORTANT: For instructions on installing an
arch over a rectangular shade, see the Installation,
Operation, and Care instructions that came with
your arch shade.
Proceed to “STEP 2 — Install the Shade” on page 9.
8