Ham Radio Outlet Catalog Spring Summer 2017

2017·17.9 MB·English

by  Ham Radio Outlet

CONTENTS
Desktop Receiver
Base Transceivers Amateur Radios
3–23
Scanners
SWL & SDR
24–28
Packet
Radio Control
All Mode RECEIVER
27-35
DX-R8T – $Call
All-Mode TRANSCEIVER 150 kHz - 30 MHz
Audio / Mics
Analog / Digital Hybrid SSB / CW / AM / FM / IQ
36-41
Monitor SWL signals from aviation, navigation and data
DX-SR9T – $Call sources.
150 kHz - 30 MHz • IQ signal output allows use of third-party SDR software. Analyzers / Meters
This hybrid, stand-alone analog and digital • Front and rear jacks. 42-45
• Direct frequency input to the dual VFO system.
SDR transceiver covers all shortwave and
• Detachable front control panel mounting options.
HF amateur bands allocated to North Ameri-
• Large LCD display. Keys / Radio Mounts
ca. Covers 160 m to 10 m amateur bands in-
cluding 5.3 MHz in SSB, CW, AM ,FM and IQ • Front speaker and 2 W audio output. 46-49
• Rugged die cast chassis.
output modes. Output power is 100 W SSB/
• Narrow ceramic filters (AM 2.4 kHz, SSB 1 kHz) and
CW and FM, 40 W in AM with low and super-
0.5 kHz audio filtering for CW. Books & Software
low power settings for QRP operation. In ad-
• 4-level RF amp / attenuator. 50–54
dition, the general coverage receiver covers
• IF shift and RIT.
135 KHz to 30 MHz in all modes.
• Noise blanker.
• Front panel separation. Weather Stations
• 3 banks / 600 memory channels.
• Large LCD display.
• Two sets of programmed search pairs and varieties of Amps
• Front facing speaker.
• Auto-keyer. scanning modes. 71–74
• Auto power off, sleep timer, dial and key locks, RX
• Simple operating commands.
indicator illumination.
• Download free SDR software from Alinco. Power Supplies
• Computer utility software to manage settings and edit
com. Programming cable ERW-4C or
memories. Batteries
ERW-7 required for SDR operation.
• Receive circuitry: Double conversion superheterodyne. 75–79
• Receiver current drain: 1.0 A.
• RIT range: ±1.2 kHz.
Coax & Baluns
• IF Frequency: 1st 71.75 MHz, 2nd 455 kHz.
• Spurious and image rejection ratio: more than 70 dB. Antenna Switches
• Antenna impedance: 50 ohm unbalanced. 79–83
• Frequency stability: ± 1 ppm.
• Power required: 13.8 VDC ± 15%.
Antenna Tuners
SSB / CW / AM / FM EDS-17
84-89
All Mode TRANSCEIVER Front panel remote kit optional. 5 m cable, front panel
bracket, unit cover and hardware.
DX-SR8T – $Call
Amateur Antennas
150 kHz - 30 MHz Handheld Receiver 90–109
The DX-SR8T covers 160 m to 10 m ama-
teur bands including 5.3 MHz in SSB, CW, Wide Band Receiver
Rotators & Towers
AM and FM modes. Output power is 100 W DJ-X11T
SSB / CW / FM and 40 W in AM with low and $Call – HRO Price 110–118
super-low power settings for QRP operation.
General coverage receiver of all modes 135 Get the power of a desktop receiver Store Locations
kHz to 30 MHz. Receiver features are similar in a handheld!! Features: 2 VFO
120–121
to the DX-R8T. simultaneous receive; covers 0.05 to
1299.995 MHz* in all modes; 1200
memories; sub-band coverage VHF Complete Index
118-171 MHz and 336 to 470 MHz
Extended 122
in AM / NFM; IQ signal can be used
Warranties with 3rd party software and discrimi- © 2017 Ham Radio Outlet ,
nator output; easy-to-use twin dials; Asterisk Design and Keydance
Available. selectable tuning steps; 3 selectable Productions. This catalog may not
be reproduced in whole or in part
See page 48. scan speeds; freeware to operate as
without permission.
a software defined radio.
*Cell band blocked.
Mid-Atlantic [phone] • Northeast [phone] • New England [phone] 3
MOBILE RADIOS
Single Band Mobiles
Dual Band Mobiles
Dual Band DR-B185HT
2 m / 70 cm 2 Meters / 85 Watts
DR-735T – $Call $Call – HRO Price
The compact DR-B185 is loaded with
high tech features: high stability PLL
synthesizer, 85 W max output, 7-digit alphanumeric display, and a wide variety
of scanning features. Yet the operation is intuitive and simple.
• TX 144-147.995 MHz; RX 136-
• 144 MHz / 440 MHz FM • Full duplex / X-band repeat. 173.995 MHz.
transceiver. • 50 / 20 / 5 W power output • Scanning functions include DCS /
• TX 144-148 MHz / 430-450 on both bands. CTCSS / priority / group and timer
MHz. • Huge alphanumeric LCD / busy modes.
• RX 108-174 MHz (AM / FM) display. • Wide and narrow FM modes
400-480 MHz (FM). • Multi-color RGB backlight. • 39 tone CTCSS / DCS / 2-tone
• Receiver double conversion. • Independent dial / vol / SQ encode and decode.
• Civil aviation and utility knobs. • High / low power setting.
receive. • Removable front control • Offset direction and frequency vari-
• 1000 channel program- head. able. DR-435TMKIII
mable memory. • Wide variety of scanning • Keypad lockout / reverse function. 440 MHz
features. • Alphanumeric tag / display dimmer. DR-235TMKIII
• Automatic illumination brightness. 220 MHz
• Time out timer. $Call – HRO Prices
• BCLO and auto power off. Features a unique multifunction backlit
• Tone-burst tones / auto-dialer. microphone with direct frequency input.
• DTMF TX speed, pause and moni- The 144 MHz, 220 MHz, and 440 MHz
toring features. models accept optional EJ-41U internal
• S-METER squelch. TNC or EJ-47U digital voice module.
• Multifunctional microphone with The MKIII TCXO supports a specifica-
Dual Band 2 m / 70 cm keypads. tion of ± 2.5 ppm frequency stability.
DR-635T – $Call • Cable cloning.
This mobile / base VHF+UHF transceiver has an expanded
range receiver.
• VHF output: 50 / 25 / 5 W; • CTCSS and DCS encode /
UHF 35 / 20 / 5 W. decode plus four tone bursts.
• 200 memories. • CTCSS tone and DCS scan.
• Cross-band repeater func- • Optional 1200 / 9600 bps
tions. packet (EJ-50U).
• Large, 6 character alphanu- • Programmable VFO and
meric display with selectable memory scan modes. DR-06T 6 Meters DR-135TMKIII
color illumination. • Air band reception. $Call – HRO Prices 2 Meters
• Removable control head. • Receive frequencies: 87.5- Catch the exciting world of the 6 $Call – HRO Price
• Internal duplexer. 107.995, 108-173.995, 335- m band with the DR-06T. Covering 2 meter FM and Airband receive (AM).
479.995 MHz. 50-53.995 MHz with an output of 50 Ignition key power control, theft alarm, 7
W, it has convenient scan features, place alphanumeric display, front panel
Extended Warranties Available a variety of selective calling tones, data input, optional internal packet
theft alarm, ignition key on/off, direct module to use with APRS®, rear panel
frequency input, and controls from the serial port connection. 100 memories,
EMS57 key pad microphone. 10 autodial memories.
Alinco Mobile Specifications
* Expand to 100 with optional EJ-19U †Expand to 240 with optional EJ-23U #TXCO with ± 2.5ppm frequency stability.
4 Phone Orders West [phone] • Mountain / Central [phone] • Southeast [phone]
HANDHELDS COMMERCIAL RADIOS
Single Band HTs Commercial UHF FM Commercial Mobile
Digital / Analog
DJ-V27T - 220 MHz Transceiver
$Call – HRO Prices DJ-MD40T – $Call
This compact, full-powered FM HT is This Alinco DMR transceiver packs a lot of
submersible to 3 ft for 30 minutes. It performance into a compact, rugged poly-
is perfect for outdoor activities. Input carbonate body. Designed to resist dust
frequencies directly from keypad. and splash, the DJ-MD40 features specs
200 memories plus one call channel. such as 1 Watt audio output with a large
39 CTCSS encode-decode settings. speaker and 2.5 ppm frequency stability.
Digital coded squelch. Capable of operating 5 W output in analog
and digital, with mixed mode, 1000 chan-
nels programmable in 64 channels
per zone.
Analog Dual Band
Dual Band HT
• DMR Tier 1 and Tier 2.
2 m / 70 cm
• RF output selectable from 5 W,
2.5 W, 1 W, and 0.2 W. DR-638T – $Call
Dual Band • Programmable up to 1000 chan-
With full duplex capability, cross-band
2 m / 70 cm nels in 64 channels per zone.
repeat and a remotely mountable control
• Dot-matrix, highly visible, color-
DJ-500T head, the DR-638 is a solid performer for
selectable backlit LED.
$Call – HRO Price base or mobile operation. The large, 6
• Digital recorder.
character alphanumeric display features
The DJ-500T provides landmobile- • Quick contact access. variable colors for custom illumination.
grade operation with 5 Watts output, • Various security passwords. Ignition key on/off feature, theft alarm,
CTCSS, DTMF, DCS and 5 tones • Various alert tone features. extended receive capabilities, a variety
as standard features. Includes • Text messages. of signaling and scan modes are also
direct frequency input, alphanu- • Standard features such as key included. The backlit, DTMF microphone
meric channel labels, 200 memory lock, talk around, EMS-77 allows remote control of the
channels, dot-matrix with 3 color lone worker, TOT, transceiver.
selectable display. Li-lon battery various call modes,
and stand charger standard. call logs, DTMF • 758 channels programmable.
tones, scan, and
• H / M / L power output settings: VHF–
more are included.
50 W / 25 W / 10 W / 5 W; UHF– 40
Tri-Band HT W / 25 W / 10 W / 5 W.
• Inversion scrambling.
• Internal duplexer – single antenna
2 m / 70 cm / 1.2 GHz
connector.
DJ-G7T • Removable control head can be re-
$Call – HRO Price motely mounted or inverted for optimal
The DJ-G7T tunes 0.531-1300 MHz* speaker placement.
continuously. Full duplex receive with • Expanded receive range includes AM
144 / 430 / 1200 MHz bands. AM civil aviation band.
and WFM modes allow you to hear • Crossband repeat.
aviation and broadcast bands. Scan • CTCSS, DCS, tone-burst tones, 2-tone
modes and options include 50 pairs and 5-tone signaling.
of programmable scan memories. • CTCSS tone and DCS scan.
Timing adjustable priority scanning and Extended • Variety of scan modes and priority
Alinco's Channel-Scope – visualize Warranties channel monitoring.
the presence of radio signals on the • TOT, BCLO, talk around, reverse and
display. Output power up to 5 Watts Available. ANI.
on 2 m. *Cell band blocked. See Page 48. • Utility software and cable cloning.
• Ignition key activated power on/off
feature.
Alinco Handheld Specifications
** Power output is determined by choice of battery pack. †at 13.8VDC * 500mW with 6 VDC #5W 220, 2.5 912MHz.
Mid-Atlantic [phone] • Northeast [phone] • New England [phone] 5
HF RIGS
IC-7600
The Flagship's
Lineage
IC-7300
The IC-7600 pushes performance to the pinnacle with the latest DSP technologies The IC-7300 HF tranceiver has features that have not been
developed for the IC-7800 / 7700. More than 45 years of analog circuit expertise gives included in previous rigs, like the RF Direct Sampling system
the IC-7600 the performance advantage. Supplied with DC power cable, HM-36 hand that is used in many software defi ned radios.The real-time
mic, spare fuses, MB-121 handle, and CW key plug. spectrum scope with waterfall function provides top-level
performance in resolution, sweep speed and dynamic range.
• Dual DSP units for transmitter / receiver • Digital notch fi lter.
and high resolution real time spectrum • Dual watch for simultaneous reception • TFT LCD that can be used • Optimum sound quality
scope. of two signals in the same band. as a touch screen. Using is achieved with a new
• 2-100 W output with 1-30 W on AM. • High stability TCXO unit with ±0.5 ppm the software keypad of the speaker unit.
• Built-in high speed auto antenna tuner. frequency stability. touch screen, you can set • Remote control operation
• Receives 0.030 - 60 MHz. • Digital voice memory to record and various functions and edit for RS-BA1.
• Transmits on amateur HF plus 6 M. replay incoming signals. memory contents. • Voice memory function.
• Three built-in 1st IF (roofi ng) fi lters: 3, • 4-channel transmit memory and • 100 W output HF / 50 MHz • Memory keyer functions
6, and 15 kHz. 20-channel receive memory. bands. for CW and RTTY.
• 5.8 inch WQVGA (400 x 240 pixel) TFT • Multi-function meter. • Built-in High-speed auto- • RTTY decode log function.
display with LED backlighting. • RF speech compressor. matic antenna tuner. • Screen capture.
• Front & rear USB connectors. • Triple band stacking register. • Multi-dial knob for smooth • SD card slot.
• Built-in PSK and RTTY operation with • Built-in memory keyer. operation. Push the multi- • USB for CI-V and audio
a USB keyboard. A PC is not required. • Microphone equalizer and adjustable dial knob and menu items input / output.
• 104 dB dynamic range and +30 dBm transmit bandwidth. are shown. Select an item • Large cooling fan system.
third-order intercept point. • Two TX / RX antenna connectors with with a touch of the screen • Multi-function meter.
• Double conversion superheterodyne automatic antenna selector. and adjust levels by turn- • 101 memory channels (99
receiver greatly improves inband IMD. • Built-in 3-step attenuator and two types ing the multi-dial knob. regular and 2 scan edge
• Dual AGC loops (one analog, one of RX preamps. • The IC-7300’s phase channels).
digital) controlled by the DSP. • 50 CTCSS tone encoder and VOX. noise characteristics are • Multiple CW functions
• Adjustable digital IF fi lter. • RIT & delta TX variable up to ±9.999 improved about 15 dB (at • Digital noise reduction.
• 99 memories and 2 scan edges. kHz. 1 kHz frequency offset) • SSB, CW, RTTY, AM and
• Noise reduction / noise blanker. • IF-DSP. when compared to other FM modes.
• Digital twin PBT to shift and narrow the • USB audio / control. transceivers. • Transmits on amateur HF
IF passband. • Remote control ops for RS-BA1. frequencies plus 6 meters.
Back by Popular Demand
IC-7700
Contester's Rig
The Contester’s rig has two 32-bit fl oating point DSP units – one for the transmitter /
receiver and the other for the spectrum scope. There is a +40 dBm 3rd order intercept
point and ultra wide dynamic range. Two IF stages and Icom's image rejection technol-
ogy allow very weak signals and very strong signals to be heard without distortion. IC-7200
HF Plus 6 m
• Spectrum waterfall display. • Digital IF fi lters/ twin passband tun-
• PC mouse operates spectrum scope. ing. Shown with optional handles
• Audio scope function. • Three roofi ng fi lters. The IC-7200 is a simple, tough rig for HF and 6 meters using
• 7” wide color TFT LCD. • Digital manual notch fi lter. the latest IF DSP technology. Even though this is an entry-class
• Waveform outline in real-time spec- • Adjustable noise blanker. transceiver, its advanced digital features are comparable to
trum scope (ON / OFF). • Ultra high stability OCXO unit. higher class rigs. Distortion and blocking from strong nearby
• Remote control ops for RS-BA1. • CW / RTTY / PSK31 operation. signals are prevented by placing DSP functions inside the
• TX delay sets the transmission timing • 50 MHz band preamp & mixer. AGC loop. The built-in digital fi lter eliminates the need for
to control an attached external linear • Microphone equalizer. optional CW and SSB fi lters. Features digital twin PBT,
amp. • RF speech compressor. manual notch fi lter, digital noise reduction, and digital noise
• Added RIT and ∂TX commands for • Digital voice recorder. blanker. The direct digital synthesizer (DDS) creates a clear,
CI-V remote control. • Increase APF volume level. clean transmit signal.
• Internal distortion reduction. • Voice TX function transmits the re-
• Improved blocking. corded audio repeatedly. Other features include: USB port for PC control, RF speech
• Icom’s DIGI-SEL. • CF memory card. compressor, full break-in for CW, selectable CW carrier point,
• Less internal phase noise. • 4 antenna connectors. adjustable CW pitch, RIT, VOX, backlght LCD display, CI-V
• Multiple AGC loops; full control. • Double conversion super-hetero- interface, 201 memory channels, preamplifi er, band stacking
• 200 W power out at full duty cycle. dyne. register, built-in voice synthesizer and built-in 20 dB attenuator.
6 Phone Orders West [phone] • Mountain / Central [phone] • Southeast [phone]
HF BASE RIGS MOBILES
The Pinnacle of HF Perfection
Dual Band Mobile
IC-2730A *
Practical Dual
Bander
with Optional
Bluetooth
Headset
HF Plus 6m LO design sets a benchmark for * Deluxe version includes MBA-5 remote head bracket
phase noise with -150 dBc / Hz at
IC-7851 10 kHz offset (and -140 dBc / Hz This mobile is a high perfor-
at 1 kHz offset). mance radio with classic 2 Single Band
The IC-7851 perfects HF opera- m / 70 cm analog operation.
The IC-7851 also has the spec-
tion with new features such as a • Wideband receiver 118- 2 m Mobile
trum waterfall function found in
1.2 kHz optimized roofing filter to 174 / 375-550 MHz.
improve in-band adjacent signal the IC-7700. The high-resolu- • Large backlit LCD IC-2300H
tion waterfall screen shows the
performance. The new design screen.
changing amplitude of frequen-
outperforms competitors’ similar • V/V & U/U simultaneous
cies over time. An enhanced
models in the 2 to 10 kHz sepa- receive.
spectrum scope promotes fast
ration tests. • Hands-free capable with
and accurate scan and can be
optional UT-133.
Unlike HF rigs using a conven- operated with PC mouse via USB
• Optional VS-3 Blue-
tional voltage controlled oscillator port. Dual scope function shows
tooth® headset.
for the 1st LO, the IC-7851 uses simultaneous activity in both
• Cross band repeater ca-
a direct digital synthesizer (DDS) bands to help search a sub-band
pability.
with a voltage controlled SAW while maintaining a run frequen- • CS-2730 free download The IC-2300 2m mobile transceiver
oscillator (VCSO). This new 1st cy on the main band. PC programming soft- boasts a powerful 65 W output, simple-
ware. to-use user interface, and built-in
• 50 Watts of output on CTCSS / DTCS encoder / decoder.
VHF and UHF.
• Built-in 50 CTCSS and • Simple operation with a large tuning
All-Band 104 DTCS tones with dial.
split tone function. • 207 alphanumeric memories.
HF
• Controller attachment to • Dynamic memory scan allows scan-
IC-718 the main unit (with op- ning of selected memory banks.
tional MBA-4). • Pocket beep function for incoming
• 1052 memory channels calls.
including 50 scan edges • DTMF autodial.
• Receives 0.03 ~ 29.995 MHz. • Built-in electronic keyer. and 2 call. • Select yellow, green or amber display.
• 101 memory channels. • VOX operation, mike compres- • Weather channel receive • PC to XCVR and XCVR to XCVR
• Modes USB, LSB, CW, RTTY, sor, RF gain control. with weather alert (USA cloning (optional software and cable
AM. • 10-key pad for direct operating version only). required).
• IF shift interference rejection. frequency entering and memory • Squelch delay and • Automatic repeater function and
• Output power: SSB / CW / RTTY: channel selection. squelch attenuator. weather channel (USA only).
5 ~ 100 W variable, AM: 2 ~ 40 • HM-207 remote control • Power supply voltage display, time-out
W variable. Warranties. mic is standard. timer, repeater lock out, auto power
• Transmits amateur HF except • 16 DTMF autodial memo- off.
60 m. See Page 48. ries. • Selectable squelch delay and squelch
• AF DSP built-in. • CI-V remote control ca- attenuator.
pability (through the op- • Wide / narrow channel setting.
Icom HF Specifications tional OPC-478UC). • Passed MIL-STD 810G specifications.
† Output is continuously adjustable from 5 to full power. * 50 W on 2 meters, 20 W 70cm. ## 2-100 W HF / 50 MHz, 2-50 W VHF, 2-35 W UHF.
Mid-Atlantic [phone] • Northeast [phone] • New England [phone] 7
HANDHELDS
Dual Band Analog HT
IC-T70A-HD IC-T70A-HD Accessories
The IC-T70A offers impressive audio
output volume, long-lasting power,
plenty of memory channels, rug-
ged construction, and analog
features:
• TX: 2 m / 70 cm bands.
RX: 136-174, 400-479 MHz
(US version).
• Power out selectable – 5 W
/ 2.5 W / 0.5 W.
• 700 mW loud audio.
• Long lasting battery life. Up
to 13.5 hours with supplied
BP-265.
• External DC power jack.
• 302 alphanumeric memories including 50
band edges and 2 call channels. Maximum
of 26 memory banks for scanning.
• Built-in CTCSS / DTCS.
• Internal VOX, WX channel, direct keypad
frequency entry, 16 DTMF autodial memories.
• IP54 / MIL-STD-810 rugged construction.
2 m Analog HT
IC-V80 HD or IC-V80 Sport
Basic Rugged 2 m
with Powerful Audio
Available either as an economical 2 m
HT with alkaline battery case (BP-263)
or with BP-265 battery and
drop-in charger.
Features include:
• IP54 / MIL STD-810 rug-
Handheld
ged construction.
• 5.5 Watts out. Batteries &
• Up to 19 hours operation Chargers
with optional BP-265.
• 207 memory channels.
"AA" Alkaline
• Built-in CTCSS / DCS.
Packs
• Internal VOX function.
BP-204, BP-208N,
• WX channel.
BP-263, BP-273
Extended Warranties
# Requires BC-147S
Available. AC adapter.
* Requires BC-123S
AC adapter.
Icom Handhelds
* Power with standard battery pack. † Frequency coverage 138-174 (receive only outside amateur bands), 440-450 MHz.
# Extended receive 118-174 MHz and 400-470 MHz. % 0.495-999.99 cellular blocked.
8 Phone Orders West [phone] • Mountain / Central [phone] • Southeast [phone]
SOFTWARE / RECEIVERS
Software IC-R6
Sport Receiver
RS-BA1
IP Remote The IC-R6 is a Signal Search Machine.
Covering 100 kHz to 1309.995 MHz
Control for
(cellular blocked and receives analog
HF Transceivers
TV only), it can search 100 channels
IC-R9500
per second. The receiver is energy-
Remotely control Icom transceiv-
efficient, designed to provide up to 15 Professional
ers through an IP network with the
hours of listening on a single charge. Communications Receiver
RS-BA1. The RS-BA1 allows you
to use the radio installed in another • +40 dBm IP3 / 109 dB wide dynamic range.
room using your home network or With 1300 alphanumeric memory • Measuring class accuracy. Dual IF filter.
a remote location over the Internet. channels, 50 scan edges, and 200 • Superior BPF unit.
The low voice latency caused by the auto-write memories, there are many • Dual DSP. 10 VFOs.
RS-BA1 provides the same opera- scanning opportunities. The bank link • 7" wide color TFT LCD.
tional experience as using an actual feature allows connecting any of the • High resolution spectrum scope. 1000 memories.
radio. Most functions and modes of 22 memory banks. The • 2 channel noise blanker.
your transceiver can be controlled. Voice Squelch Control • 5 roofing filters. 2 point manual notch filter.
opens the squelch only • 0.005-3335 MHz. Cellular blocked.
The RS-BA1 has two component ap- when a modulated signal • All bands: SSB, CW, FSK, AM. FM, WFM on some.
plications: System Configuration to set is detected. • Digital voice recorder.
up the IP address and other settings, • 4 antenna connectors
NEW! Red and Blue
and Remote Control allows you to
versions now available! Available early 2017
control the radio.The display on the
RS-BA1 is similar to the radio's front
panel. Supports the IC-7100, 7200, IC-R6
7410, 7300, 7600, or 9100 with USB Accessories
connection to a PC. Also the IC7800 or
7700 connected to a PC with an RS-
232C cable plus S/P DIF or ACC cable.
Icom Cloning
Icom cloning software for Windows
IC-R8600
allows you to preprogram memory
channels with operating frequen- Wideband Receiver
cies, set tones, set power levels, set • Ultra-wide frequency coverage (10 kHz-3 GHz) with
squelch levels, set up auto-dial DTMF RSSI (received signal strength indication) function.
frequencies, and exchange operating • Fast moving, real-time spectrum scope and waterfall.
frequencies. Call for price quotes. • Decodes multiple digital protocols, including D-
• CS-R6 without cable (R6).. STAR®, NXDN™, dPMR™ and APCO P25.
• CS-V80 without cable (V80A). • Large 4.3 inch TFT color touch screen display.
• CS-2300H without cable (2300H). • Clear audio quality using FPGA / DSP base architec-
• CS-T70A without cable (T70A)*. ture with superheterodyne circuitry.
• CS-7100 without cable • Optional RS-R8600 PC remote control software al-
(IC-7100)*. lows control of all receiver functions.
• CS-9100 without cable • I/Q signal output for use with third-party SDR software
(IC-9100)*. and/or external decoding.
• RS-92 for IC-92AD. • SD card slot for logs and voice recording.
* OPC-478U USB cable optional • Optional SP-39AD external speaker with integrated
power supply.
The IC-R8600 has not been approved by the Federal Communications Commission. This
Power Supply device may not be sold or leased, or be offered for sale or lease, until approval of the FCC
has been obtained.
Speaker HF Auto Antenna Tuner
SP-38
AH-4
The AH-4 auto-tuner cov-
ers all amateur bands from
This high quality 80 to 6 meters when used with a
speaker is perfect minimum 23' long wire antenna. With
for the IC-7300. the optional AH-2b antenna element, tune
Rated output is 5 40 through 6 meters for mobile operation. It
W, maximum input has automatic band changes and tunes usually in less than
PS-126 power is 7 W. Im- 2.5 seconds. The 45 memories store SWR minimum and
Matching supply for IC-7600. pedance is 8Ω. tuning combinations. Requires only 300 mW to tune and
HRO Price $CALL HRO Price CALL handles up to 120 Watts. HRO Price $279.95
Mid-Atlantic [phone] • Northeast [phone] • New England [phone] 9
D-STAR CENTRAL
D-Star Mobiles
HF and More With D-Star
ID-4100
HF Plus 6 m / VHF / UHF
Dual Band
with D-STAR
D-STAR
IC-7100 GPS Mobile
Terminal & access point modes. Extend D-STAR coverage with the In-
ternet DR (D-STAR repeater) function. (Optional data cable and free-
download application required.)
• Full dot-matrix display with • Bluetooth capable for hands-
easy-to-read characters and free operation. (Optional
icons. Bluetooth unit and readset re-
Multi-Band • Compact, detachable control- quired.)
ler for fl exible installation. • Enhanced remote control apps
All-Mode Operations • Integrated GPS and microSD for smart devices. (Optional
card slot. (MicroSD card re- Bluetooth unit and free down-
• Intuitive touch screen interface. • Easy vehicle mounting (optional quired.) load application required.)
• Easy-to-see,easy-to-use slant MBF-1).
top controller. • IF DSP controlled digital fea- ID-5100A Deluxe
• Built-in high effeciency oval tures. The 32- bit fl oating point
Dual Band D-STAR
speaker on the controller. DSP supports many digital pro-
• D-STAR DV mode digital voice cessing features such as digital with
and low speed data communica- IF fi lter, twin PBT and manual Touch
tions. notch fi lters.
Screen
• 505 memory channels. • Remote Control Software (op-
• SWR graphic display. tional RS-BA1 IP).
• Optional MBF-1 mounting base. • CW full break-in.
• Built-in SD card slot for voice • CW auto tuning.
storage and data cloning. • USB Audio/Control.
• Built-in RTTY functions. • IF-DSP.
This ID-5100A dual band D-STAR mobile has a large, responsive touch
screen LCD and Bluetooth connectivity.
• Wideband receive (118-137 • Includes MBA-2 remote head
MHz (AM), 137-174 / 375-550 bracket.
MHz only). • RS-MS1A Android application:
• Antenna RX diversity (second a free-to-use download.
antenna connector). • Independent VHF and UHF
• DTMF decode / DV / FM re- band units (VV / UU capable)
peater list. for 50 W output.
• Optional UT-133 Bluetooth unit • D-Plus refl ector usability (se-
enables audio accessory con- lect “refl ector” in TO fi eld).
nection and Android terminal • DV dual watch for simultane-
VHF / UHF Satellite Plus HF / 6 m connection (CI-V via Bluetooth ously waiting in two DV voice
SPP profi le). streams (decodes one only).
Plus D-STAR DV Mode
• Optional VS-3 Bluetooth pen- • Home button (same as ID-51
IC-9100 dant earpiece mic. feature).
• 1,000 memory channels. • HM-207 control microphone is
With built-in satellite mode operation, the IC-9100 covers HF / 50 MHz,
• Built-in GPS engine. supplied as standard.
144 / 430 (440) MHz, and 1200 MHz frequencies. The optional UX-9100
is required for 1200 MHz. The rig has 100 Watts output on HF / 50 / 144
MHz; 75 Watts on 430 (440) MHz; 10 Watts on 1200 MHz.
Extended Warranties Available
• Double superheterodyne receiver with image rejection mixer.
for Icom Radios.
• SSB, CW, RTTY, AM, and (with the optional D-STAR unit) DV mode.
• 32-bit fl oating point DSP and 24-bit AD / DA converter. Details on Page 48.
• Optional 3 kHz (FL-431) and 6 kHz (FL-430) 1st IF (roofi ng) fi lters.
• USB Audio/Control. IF-DSP.
10 Phone Orders West [phone] • Mountain / Central [phone] • Southeast [phone]