Glass blowing shop equipment guide - Arnold Gruppe

25 Pages·2012·1.55 MB·English

CHOICE ASSISTANCE FOR EQUIPMENT OF A GLASS BLOWING SHOP
A) Basic arrangement of a lamp glass blower’s working place
B) Sugges(cid:415) ons for the basic equipment of a glass blowing shop with
a work place for one glass blower.
C) Sugges(cid:415) ons for the expansion of glass blowing shop depending on
the quan(cid:415) ty of the employees and the line of produc(cid:415) on.
D) For big volume laboratory glass appliances as well as for the pro-
cessing of quartzglass, we refer in our main catalogue correspon-
ding equipments and corresponding accessories.
For further personal advice we are always at your disposal.
A
FURNITURE / BURNERS & ACCESSORY
1
No. 38/15
PIECE Glassblower’s working table with
solid base frame made of steel
 bench top 196 x 78 cm, raised edges on
three sides.
 Bench tops are equipped with a special
material, 10 mm thick with the following
advantages: asbestos-free, resistant, heat-
resistant, an(cid:415) glare, mechanical, deeply
colored
Alterna(cid:415) vely:
Nr. 38/50
1 Glassblower’s working table
with ceran working plate
PIECE
 dimensions of table: 2.500 x 1.500 x 40 mm
 Ceran working plate: 1.500 x 590 x 4 mm
 C-base frame with spindle height adjust-
ment, mounted at the frame, for an indi-
vidual and op(cid:415) mal adjustment of working
height
No. 34/1
Roller
1
 consis(cid:415) ng of ball-bearing light alloy rollers
PIECE (diameter 65 mm)
 horizontally and ver(cid:415) cally adjustable and
laterally rotatable
 with swivel-type pull-out joint
 with base in order to fasten it on the
glassblower’s table
 for reworking glass tubes with diameters
up to 200 mm
2
A
BURNERS & ACCESSORY
1
No. 101 PSL / ESL
PIECE
Bench burner „Thueringian
model“, sperate gas-system
with three interchangeable jets for varying
fl ames. The burners are equipped with a spe-
cial fl ame stabilizing system, that means, they
could also be operated with a high air propor-
(cid:415) on for cooling the fl ames. The burners are
mounted on a cast iron foot with ball joint.
Burners for propane gas with needle valve.
 6 mm bore
 very good fl ame adjustment from pin-point
fl ame to large bushy fl ame
 opera(cid:415) on either with gas and oxygen or gas
and air with slight addi(cid:415) on of oxygen for
fl ame stabiliza(cid:415) on
No. 114/1 PSL / ESL A
Noiseless Bench burner „ZENIT“,
sperate gas-system
1
PIECE PSL propane gas, oxygen, air
ESL natural gas, oxygen, air
Noiseless bench burner, for gas and oxygen,
burners for natural gas and propane with
special fl ame stabiliza(cid:415) on system allowing to
operate the burner even with a surplus of air
and thus with a cooler fl ame - mounted on so-
lid cast iron foot with ball joint.
 diameter of head: 40 mm
 for tube diameter: 100 mm
Advantages:
 low noise working method with a large
fi eld of applica(cid:415) on
 stable, homogeneous fl ame forma(cid:415) on,
from pinpoint fl ame to
bushy fl ame, steplessly variable via a single
twis(cid:415) ng grip
 burning media are controlled via ball
valves, nearly service-free
and resistant to wear
 op(cid:415) mum energy fi eld through intensive
igni(cid:415) on of gases
 long durability by using high-quality mate-
rials and construc(cid:415) onal
parts - solid burner head made of non-
scaling stainless steel
 connec(cid:415) on glands with thread
3
A
BURNERS & ACCESSORY
No. 152 b
Gas oxygen lox consump(cid:415) on
1
device
PIECE
foot-operated, 3 connec(cid:415) ons for gas and oxy-
gen resp. gas, oxygen and air.
Construc(cid:415) on:
Control block with screwed-in inlet and outlet
sockets mounted together with the footpedal
on the base plate. Media control by means of
maintenance-free, tappet-operated valves.
Advantages:
 no impairment due to hand-operated
fl ame adjustment
 con(cid:415) nuous adjustment of media supply,
reproducible
fl ame adjustment
 energy saving
 variable opening sequence and pilot fl ame
No. 199
1
Ignitor - „Long-Flame“
PIECE
No. 210 W
1
Compressed air blower
PIECE
in compact construc(cid:415) on with fl anged motor
 Volume fl ow 7 cbm/h
 3-phase
 230/400 V
 50 cycles
 0,25 kW
4
A
BURNERS & ACCESSORY
No. 141/3 ES A / PSL A
1
Hand torch, surface mix with
PIECE mul(cid:415) ple jet head
Propane gas execu(cid:415) on operates with a low
amount of addi(cid:415) onal air in order to avoid
the dazzle white fl ame core. Burner tubes,
valves and burner cap are made of brass, jets
of stainless steel. Execu(cid:415) on with connec(cid:415) ng
glands.
 diameter of head: 18 mm
Advantages:
 silent principle of working
 high hea(cid:415) ng capacity and concentrated
fl ame range due to
separately controllable middle jet
 homogeneous, variable fl ame forma(cid:415) on,
ranging from sharp,
1
concentrated pin-point fl ames to large
bushy fl ames
PIECE
No. 114/4
Glass blower glasses
Standard safety glasses for glassblowers, with
special fi lter lenses made of Didymium glass.
1 No. 99/16 b
Plurostoppers
PIECE
for glassblowing workshops, made of red si-
licone, heat - resis(cid:415) ng up to approx. 250° C,
this execu(cid:415) on is resistant against hot oil, ga-
soline, oxidizing chemicals, ozone and sodium
hydroxide.
No. 62/1
WIDIA cu(cid:427) ng knife
1
PIECE With double-edged interchangeable carbide-
(cid:415) pped blade, curved blade.
5
A
TOOLS & EQUIPMENT
No. 1 C
Reamer
 45 x 45 mm
 made of brass sheet metal
 1,5 mm thick
 obtuse form
1
PIECE
No. 3 C
Reamer
 60 x 14 mm
 made of brass sheet metal
 1,5 mm thick
 form: taper 1:10
1
PIECE
No. 40
Forceps
1x No. 40b: 160 mm
1x No. 40f: 300 mm
2
 made of hardened steel
PIECES
 with rounded (cid:415) ps
 nickel-plated
No. 7/1Q
Carbon plates
2
PIECES 1x No. 7/1Qa: 75 x 50 x 10 mm
1x No. 7/1Qb: 150 x 100 x 10 mm
 extremely heat resistant
 for reworking quartz glass
 with handle
6
A
TOOLS & EQUIPMENT
No. 10/1Q
Hexagon carbons for standard
ground joints
1x 10/1Qc: NS 10
1x 10/1Qe: NS 14,5
1x 10/1Qg: NS 19
1x 10/1Qi : NS 29
5
1x 10/1Qk: NS 34,5
PIECES
 made of heat resis(cid:415) ng material
 form-taper 1:10
 length 150 mm
 with internal screw thread for fastening of
the handle
 for reworking quartz glass
No. 76/5
Precision-sliding calliper from
stainless steel
1
 fully hardened
PIECE  for outer-, inner- and depth measurements
 measuring range 150 mm
No. 6/1
Tungsten rods
1x No. 6/1b: 1 mm diameter
1x No. 6/1d: 2 mm diameter
1x No. 6/1f: 3 mm diameter
3  length: 100 mm
PIECES
No. 6/2
Holder for tungsten rods
1x No. 6/2a: clamping range 0 - 1,2 mm
3 1x No. 6/2b: clamping range 1,3 - 2,0 mm
1x No. 6/2c: clamping range 2,5 - 3,0 mm
PIECES
 with handle made of plas(cid:415) c
7
B
FURNITURE / BURNERS & ACCESSORY
1
No. 38/15
PIECE Glassblower’s working table with
solid base frame made of steel
 bench top 196 x 78 cm, raised edges on
three sides.
 Bench tops are equipped with a special
material, 10 mm thick with the following
advantages: asbestos-free, resistant, heat-
resistant, an(cid:415) glare, mechanical, deeply
colored
Alterna(cid:415) vely:
Nr. 38/50
1 Glassblower’s working table
with ceran working plate
PIECE
 dimensions of table: 2.500 x 1.500 x 40 mm
 Ceran working plate: 1.500 x 590 x 4 mm
 C-base frame with spindle height adjust-
ment, mounted at the frame, for an indi-
vidual and op(cid:415) mal adjustment of working
height
1
PIECE No. 101 PSL / ESL
Bench burner „Thueringian
model“, sperate gas-system
with three interchangeable jets for varying
fl ames. The burners are equipped with a spe-
cial fl ame stabilizing system, that means, they
could also be operated with a high air propor-
(cid:415) on for cooling the fl ames. The burners are
mounted on a cast iron foot with ball joint.
Burners for propane gas with needle valve.
 6 mm bore
 very good fl ame adjustment from pin-point
fl ame to large bushy fl ame
 opera(cid:415) on either with gas and oxygen or gas
and air with slight addi(cid:415) on of oxygen for
fl ame stabiliza(cid:415) on
8
B
BURNERS & ACCESSORY
No. 114/1 PSL / ESL A
Noiseless Bench burner „ZENIT“,
sperate gas-system
1
PIECE PSL propane gas, oxygen, air
ESL natural gas, oxygen, air
Noiseless bench burner, for gas and oxygen,
burners for natural gas and propane with
special fl ame stabiliza(cid:415) on system allowing to
operate the burner even with a surplus of air
and thus with a cooler fl ame - mounted on so-
lid cast iron foot with ball joint.
 diameter of head: 40 mm
 for tube diameter: 100 mm
Advantages:
 low noise working method with a large
fi eld of applica(cid:415) on
 stable, homogeneous fl ame forma(cid:415) on,
from pinpoint fl ame to
bushy fl ame, steplessly variable via a single
twis(cid:415) ng grip
 burning media are controlled via ball
valves, nearly service-free
and resistant to wear
 op(cid:415) mum energy fi eld through intensive
igni(cid:415) on of gases
 long durability by using high-quality mate-
rials and construc(cid:415) onal
parts - solid burner head made of non-
scaling stainless steel
 connec(cid:415) on glands with thread
No. 152 b
Gas oxygen lox consump(cid:415) on
1
device
PIECE
foot-operated, 3 connec(cid:415) ons for gas and oxy-
gen resp. gas, oxygen and air.
Construc(cid:415) on:
Control block with screwed-in inlet and outlet
sockets mounted together with the footpedal
on the base plate. Media control by means of
maintenance-free, tappet-operated valves.
Advantages:
 no impairment due to hand-operated
fl ame adjustment
 con(cid:415) nuous adjustment of media supply,
reproducible
fl ame adjustment
 energy saving
 variable opening sequence and pilot fl ame
9
B
BURNERS & ACCESSORY
No. 141/3 ES A / PSL A
1
Hand torch, surface mix with
PIECE mul(cid:415) ple jet head
Propane gas execu(cid:415) on operates with a low
amount of addi(cid:415) onal air in order to avoid
the dazzle white fl ame core. Burner tubes,
valves and burner cap are made of brass, jets
of stainless steel. Execu(cid:415) on with connec(cid:415) ng
glands.
 diameter of head: 18 mm
Advantages:
 silent principle of working
 high hea(cid:415) ng capacity and concentrated
fl ame range due to
separately controllable middle jet
 homogeneous, variable fl ame forma(cid:415) on,
ranging from sharp,
concentrated pin-point fl ames to large
bushy fl ames
1
PIECE No. 176/3 P
Pressure reducing valve for
propane
1
PIECE No. 114/elegant
114/elegant - UV-Protect
The fi rst glassblower’s glasses which can
be referred to as safety glasses.
Safety glasses for glassblowers according to
DIN EN 166, 177:2002, annex II of the PSA-
guidelines 89/686/EWG. Due to an innova(cid:415) ve
didymium fi lter glass, these glasses provide
next to the already known protec(cid:415) on against
sodium radia(cid:415) on, an addi(cid:415) onal protec(cid:415) on
against the damaging UV- and infrared radi-
a(cid:415) on.
 Filter eff ect for UV-protec(cid:415) ve fi lter
Protec(cid:415) on level 2 – 4
 Filter eff ect for IR-protec(cid:415) ve fi lter
Protec(cid:415) on level 4 – 4
Note:
The light transmission for daylight amounts to
less then 10%. Please make certain of suffi ci-
ent ligh(cid:415) ng of the work area. The laterals of
the glasses do not have any fi lter eff ect, the
glasses can only protect against direct op(cid:415) cal
radia(cid:415) on.
10