Excalibur High-Speed JFET-Input Op Amps - Texas Instruments

79 Pages·2016·1.94 MB·English

TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
(cid:0) (cid:0)
Direct Upgrades to TL05x, TL07x, and On-Chip Offset Voltage Trimming for
TL08x BiFET Operational Amplifiers Improved DC Performance
(cid:0) (cid:0)
Greater Than 2× Bandwidth (10 MHz) and Wider Supply Rails Increase Dynamic
3× Slew Rate (45 V/µs) Than TL08x Signal Range to ±19 V

description
The TLE208x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew
rate of the TL07x and TL08x families of BiFET operational amplifiers. The TLE208x also have wider
supply-voltage rails, increasing the dynamic-signal range for BiFET circuits to ±19 V. On-chip zener trimming
of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE208x are
pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in
existing designs.
BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without
sacrificing the output drive associated with bipolar amplifiers. This makes these amplifiers better suited for
interfacing with high-impedance sensors or very low level ac signals. They also feature inherently better ac
response than bipolar or CMOS devices having comparable power consumption.
Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to
observe common-mode input-voltage limits and output voltage swing when operating from a single supply. DC
biasing of the input signal is required and loads should be terminated to a virtual ground node at mid-supply.
Texas Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from
single supplies.
The TLE208x are fully specified at ±15 V and ±5 V. For operation in low-voltage and/or single-supply systems,
Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended.
When moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth
requirements and output loading.
For BiFET circuits requiring low noise and/or tighter dc precision, the TLE207x offer the same ac response as
the TLE208x with more stringent dc and noise specifications.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
LinCMOS is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date. Copyright  2001, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081 AVAILABLE OPTIONS
PACKAGED DEVICES
CCHHIIPP
VIOmax SMALL CHIP CERAMIC PLASTIC
TA AT 25°C OUTLINE CARRIER DIP DIP FORM
(Y)
(D) (FK) (JG) (P)
3 mV TLE2081ACD TLE2081ACP —
00°°CC ttoo 7700°°CC — —
6 mV TLE2081CD TLE2081CP TLE2081Y
3 mV TLE2081AID TLE2081AIP
–4400°°CC ttoo 8855°°CC — — —
6 mV TLE2081ID TLE2081IP
3 mV TLE2081AMFK TLE2081AMJG
–5555°°CC ttoo 112255°°CC — — —
6 mV TLE2081MFK TLE2081MJG
†The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2081ACDR).
‡Chip forms are tested at TA = 25°C only.
TLE2082 AVAILABLE OPTIONS
PACKAGED DEVICES
VIOmax SMALL CHIP CERAMIC PLASTIC CHIP FORM
TA AT 25°C OUTLINE CARRIER DIP DIP (Y)
(D) (FK) (JG) (P)
4 mV TLE2082ACD TLE2082ACP
00°°CC ttoo 7700°°CC — — —
7 mV TLE2082CD TLE2082CP
4 mV TLE2082AID TLE2082AIP
–4400°°CC ttoo 8855°°CC — — TTLLEE22008822YY
7 mV TLE2082ID TLE2082IP
4 mV TLE2082AMD TLE2082AMFK TLE2082AMJG TLE2082AMP
–5555°°CC ttoo 112255°°CC —
7 mV TLE2082MD TLE2082MFK TLE2082MJG TLE2082MP
‡The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2082ACDR).
‡Chip forms are tested at TA = 25°C only.
TLE2084 AVAILABLE OPTIONS
PACKAGED DEVICES
CCHHIIPP
VIOmax SMALL CHIP CERAMIC PLASTIC
TA AT 25°C OUTLINE CARRIER DIP DIP FORM
(Y)
(DW) (FK) (J) (N)
4 mV TLE2084ACDW TLE2084ACN —
00°°CC ttoo 7700°°CC — —
7 mV TLE2084CDW TLE2084CN TLE2084Y
4 mV TLE2084AMFK TLE2084AMJ
–5555°°CC ttoo 112255°°CC — — —
7 mV TLE2084MFK TLE2084MJ
†The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2084ACDWR).
‡Chip forms are tested at TA = 25°C only.
2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081 TLE2082 TLE2084 TLE2084
D, JG, OR P PACKAGE D, JG, OR P PACKAGE J OR N PACKAGE DW PACKAGE
(TOP VIEW) (TOP VIEW) (TOP VIEW) (TOP VIEW)
OFFSET N1 1 8 NC 1OUT 1 8 VCC+ 1OUT 1 14 4OUT 1OUT 1 16 4OUT
IN– 2 7 VCC+ 1IN– 2 7 2OUT 1IN– 2 13 4IN– 1IN– 2 15 4IN–
IN+ 3 6 OUT 1IN+ 3 6 2IN– 1IN+ 3 12 4IN+ 1IN+ 3 14 4IN+
VCC– 4 5 OFFSET N2 VCC– 4 5 2IN+ VCC+ 4 11 VCC– VCC+ 4 13 VCC–
2IN+ 5 10 3IN+ 2IN+ 5 12 3IN+
2IN– 6 9 3IN– 2IN– 6 11 3IN–
2OUT 7 8 3OUT 2OUT 7 10 3OUT
NC 8 9 NC
TLE2081 TLE2082 TLE2084
FK PACKAGE FK PACKAGE FK PACKAGE
(TOP VIEW) (TOP VIEW) (TOP VIEW)
T N1 NC 1OUT NCVCC +NC 1IN – 1OUT NC4OUT 4IN –
E
S
F 3 2 1 20 19 3 2 1 20 19
NC OF NCNC NC NC 4 18 NC 1IN+ 4 18 4IN+
1IN– 5 17 2OUT NC 5 17 NC
NC 43 2 1 20 1918 NC NC 6 16 NC VCC+ 6 16 VCC–
IN– 5 17 VCC+ 1IN+ 7 15 2IN– NC 7 15 NC
NC 6 16 NC NC 8 9 10 11 12 1314 NC 2IN+ 8 9 10 11 12 1314 3IN+
IN+ 7 15 OUT
NC 8 9 10 11 12 1314 NC NC VCC – NC2IN + NC 2 IN – 2OUT NC3OUT 3IN –
NC C – NCN2 NC
V C ET
S
F
F
O
NC – No internal connection
symbol
IN+ +
OUT
IN– –
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2081. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(1) (8)
(1)
OFFSET N1 VCC+
(7)
(3)
IN+ +
(6)
(2) OUT
IN– –
(5) (4)
OFFSET N2
VCC–
(2)
85
(7)
(3)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
(4) (5) ALL DIMENSIONS ARE IN MILS.
(6)
PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
58
4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2082Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2082. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS VCC+
(8)
(3)
(8) 1IN+ +
(1) (7) (1)
(2) 1OUT
1IN– –
(5)
+ 2IN+
(7)
2OUT (6)
– 2IN–
(4)
VCC–
90 (2) (6)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
(3) (5)
(4) PIN (4) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
80
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2084Y chip information
This chip, when properly assembled, displays characteristics similar to the TLE2084. Thermal compression or
ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with conductive
epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS VCC+
(4)
(3)
1IN+ +
(2) (1) (14) (13) (1)
(2) 1OUT
1IN– –
(5)
+ 2IN+
(7)
(3) (12) 2OUT (6)
– 2IN–
(10)
3IN+ +
(8)
(9) 3OUT
3IN– –
(12)
+ 4IN+
(14)
4OUT (13)
– 4IN–
(11)
VCC–
150 (4) (11)
CHIP THICKNESS: 15 TYPICAL
BONDING PADS: 4 × 4 MINIMUM
TJmax = 150°C
(5) (10)
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
(6) (7) (8) (9) PIN (11) IS INTERNALLY CONNECTED
TO BACKSIDE OF THE CHIP.
100
6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
equivalent schematic (each channel)
VCC+
Q1 R1 R2 R6 R11
Q11
Q17
Q3
Q8 Q23
R3 D2 Q28
C1 Q13 Q20
IN– Q24
D3
Q4 Q12 Q15 Q19 R13
R12 OUT
P
O IN+
S
T OFF Q9 Q16 Q30
IC
E
BO R8 Q25 C6
X 6 Q5
5 C3
530 Q18 Q29
3
D• Q2 D1
ALL Q6 Q14 Q21 Q22 Q26 Q27
A
S Q10
, T
E C5 E
XAS 7 Q7 R4 R7 Q31 R14 XC
52 R5 C4 R9 R10 A
65 C2 SL L
NOTE A: OFFSET N1 and OFFSET N2( OsaerFeeF oSNnEolyTt e aN vA1a)iliable on the TLE208V1CxC d–evices. (OseFeF SNEoTte N A2) OS182B – FEBOPERIBUR HIGTLE208x
RUAATH, T
TrCaOnsMisPtoOrsNEANCTTUAL TDLEEV323IC08E1 COMPOTNLEE5N270T8 C2OUNT TLE1124084 RY 1997 – RIONAL-SPEEDLE208x
Resistors 25 37 74 EV A JA
Diodes 8 5 10 ISEDMPFE, TL
Capacitors 6 11 22 JUNE 20LIFIET-INPE208
0RUx
1
STY
7
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 V
CC+
Supply voltage, V (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –19 V
CC–
Differential input voltage range, V (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V to V
ID CC+ CC–
Input voltage range, V (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V to V
I CC+ CC–
Input current, I (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 mA
I
Output current, I (each output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±80 mA
O
Total current into V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
CC+
Total current out of V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 mA
CC–
Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, T : C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
A
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to 125°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Case temperature for 60 seconds: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300°C
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC–.
2. Differential voltages are at IN+ with respect to IN–.
3. The output can be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum
dissipation rate is not exceeded.
DISSIPATION RATING TABLE
TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 85°C TA = 125°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING POWER RATING
D 725 mW 5.8 mW/°C 464 mW 377 mW 145 mW
DW 1025 mW 8.2 mW/°C 656 mW 533 mW 205 mW
FK 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
J 1375 mW 11.0 mW/°C 880 mW 715 mW 275 mW
JG 1050 mW 8.4 mW/°C 672 mW 546 mW 210 mW
N 1150 mW 9.2 mW/°C 736 mW 598 mW 230 mW
P 1000 mW 8.0 mW/°C 640 mW 344 mW 200 mW
recommended operating conditions
C SUFFIX I SUFFIX M SUFFIX
UUNNIITT
MIN MAX MIN MAX MIN MAX
Supply voltage, VCC± ±2.25 ±19 ±2.25 ±19 ±2.25 ±19 V
VCC± = ±5 V –0.9 5 –0.8 5 –0.8 5
CCoommmmoonn-mmooddee iinnppuutt vvoollttaaggee, VVIICC VV
VCC± = ±15 V –10.9 15 –10.8 15 –10.8 15
Operating free-air temperature, TA 0 70 –40 85 –55 125 °C
8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless
otherwise noted)
TLE2081C TLE2081AC
PPAARRAAMMEETTEERR TTEESSTT CCOONNDDIITTIIOONNSS TTA†† UUNNIITT
MIN TYP MAX MIN TYP MAX
25°C 0.34 6 0.3 3
VVIIOO IInnppuutt ooffffsseett vvoollttaaggee mmVV
VIC = 0, VO = 0, Full range 8 5
Temperature coefficient RS = 50 Ω
αVIO of input offset voltage Full range 3.2 29 3.2 29 µV/°C
25°C 5 100 5 100
IIIIOO IInnppuutt ooffffsseett ccuurrrreenntt nnAA
VIICC = 0,, VOO = 0,, Full range 1.4 1.4
See Figure 4 25°C 15 175 15 175
IIIIBB IInnppuutt bbiiaass ccuurrrreenntt nnAA
Full range 5 5
55 55 55 55
25°C to to to to
Common-mode input –1 –1.9 –1 –1.9
VVIICCRR RRSS == 5500 ΩΩ VV
voltage range 55 55
Full rangge to to
–0.9 –0.9
25°C 3.8 4.1 3.8 4.1
IIOO == –220000 µµAA
Full range 3.7 3.7
Maximum positive peak 25°C 3.5 3.9 3.5 3.9
VVOOMM+ IIOO == –22 mmAA VV
output voltage swing Full range 3.4 3.4
25°C 1.5 2.3 1.5 2.3
IIOO == –2200 mmAA
Full range 1.5 1.5
25°C –3.5 –4.2 –3.5 –4.2
IIOO == 220000 µµAA
Full range –3.4 –3.4
Maximum neggative peak 25°C –3.7 –4.1 –3.7 –4.1
VVOOMM– IIOO == 22 mmAA VV
output voltage swing Full range –3.6 –3.6
25°C –1.5 –2.4 –1.5 –2.4
IIOO == 2200 mmAA
Full range –1.5 –1.5
25°C 80 91 80 91
RRLL == 660000ΩΩ
Full range 79 79
Largge-siggnal differential 25°C 90 100 90 100
AAVVDD VVOO == ±± 22.33 VV RRLL == 22 kkΩΩ ddBB
voltage amplification Full range 89 89
25°C 95 106 95 106
RRLL == 1100 kkΩΩ
Full range 94 94
ri Input resistance VIC = 0 25°C 1012 1012 Ω
ccii IInnppuutt ccaappaacciittaannccee VIICC = 0,, Common mode 25°C 11 11 ppFF
See Figure 5 Differential 25°C 2.5 2.5
Open-loop output
zo impedance f = 1 MHz 25°C 80 80 Ω
CCMMRRRR Common-mode VIICC = VIICCRRmin,, 25°C 70 89 70 89 ddBB
rejection ratio VO = 0, RS = 50 Ω Full range 68 68
Supplyy-voltagge rejjection VCCCC±± = ±5 V to±15 V, 25°C 82 99 82 99
kkSSVVRR ratio(∆VCC±/∆VIO) VO = 0, RS = 50 Ω Full range 80 80 ddBB
†Full range is 0°C to 70°C.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9
TLE208x, TLE208xA, TLE208xY
EXCALIBUR HIGH-SPEED JFET-INPUT
OPERATIONAL AMPLIFIERS
SLOS182B – FEBRUARY 1997 – REVISED JUNE 2001
TLE2081C electrical characteristics at specified free-air temperature, VCC± = ±5 V (unless
otherwise noted) (continued)
TLE2081C TLE2081AC
PPAARRAAMMEETTEERR TTEESSTT CCOONNDDIITTIIOONNSS TTA†† UUNNIITT
MIN TYP MAX MIN TYP MAX
25°C 1.35 1.6 2.2 1.35 1.6 2.2
IICCCC SSuuppppllyy ccuurrrreenntt VVOO == 00, NNoo llooaadd mmAA
Full range 2.2 2.2
Short-circuit output VID = 1 V –35 –35
IIOOSS VVOO == 00 2255°°CC mmAA
current VID = –1 V 45 45
†Full range is 0°C to 70°C.
TLE2081C operating characteristics at specified free-air temperature, VCC± = ±5 V
TLE2081C TLE2081AC
PPAARRAAMMEETTEERR TTEESSTT CCOONNDDIITTIIOONNSS TTA†† UUNNIITT
MIN TYP MAX MIN TYP MAX
25°C 35 35
SR+ Positive slew rate Full V/µs
VO(PP) = ±2.3 V, range 23 23
AAVVDD = –11, RRLL = 22 kkΩΩ, 25°C 38 38
CCLL == 110000 pFF,, SSeeee FFiigguurree 11
SR– Negative slew rate Full V/µs
23 23
range
AVD = –1, To 10 mV 0.25 0.25
tts SSeettttlliinngg ttiimmee R2-LV = s t1e pk,,Ω, 2255°°CC µµss
To 1 mV 0.4 0.4
CL = 100 pF
Eqquivalent input noise f = 10 Hz 28 28
VVn 2255°°CC nnVV//√√HHzz
voltage f = 10 kHz 11.6 11.6
RS = 20 Ω, f = 10 Hz to
66 66
Peak-to-peak eqquivalent See Figure 3 10 kHz
VVNN((PPPP)) input noise voltage f = 0.1 Hz to 2255°°CC µµVV
0.6 0.6
10 Hz
Equivalent input noise
In current VIC = 0, f = 10 kHz 25°C 2.8 2.8 fA/√Hz
VO(PP) = 5 V, AVD = 10,
Total harmonic distortion
TTHHDD ++ NN plus noise ff = 11 kkHHzz, RRLL = 22 kkΩΩ, 2255°°CC 00.001133%% 00.001133%%
RS = 25 Ω
BB11 UUnniittyy-ggaaiinn bbaannddwwiiddtthh VII = 10 mV,, RLL = 2 kΩ,, 2255°°CC 99.44 99.44 MMHHzz
CL = 25 pF, See Figure 2
BBOOMM Mbaanxdimwuidmth output-swingg VROOL ((=PP 2PP ))k =Ω 4, V,, ACVVLDD = =2 5– p1F,, 2255°°CC 22.88 22.88 MMHHzz
φφm PPhhaassee mmaarrggiinn aatt uunniittyy ggaaiinn VII = 10 mV,, RLL = 2 kΩ,, 2255°°CC 5566°° 5566°°
CL = 25 pF, See Figure 2
†Full range is 0°C to 70°C.
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265