CIVIL ENGINEERING WORKS - Hong Kong International Airport

330 Pages·2008·1.4 MB·English

GENERAL

MATERIALS AND WORKMANSHIP

SPECIFICATION

VOLUME 1 OF 4
(SECTIONS 1 – 14)

CIVIL ENGINEERING WORKS

ISSUE NO. 4
JANUARY

2004
[this page not used]
GENERAL MATERIALS AND WORKMANSHIP SPECIFICATION

TABLE OF CONTENTS

VOLUME 1 CIVIL ENGINEERING WORKS

SECTION 1 ABBREVIATIONS, STANDARDS AND GENERAL
SECTION 2 TEMPORARY WORKS
SECTION 3 SITE CLEARANCE AND DEMOLITION
SECTION 4 LANDSCAPE SOFTWORKS AND ESTABLISHMENT WORKS
SECTION 5 FENCING
SECTION 6 DRAINAGE WORKS
SECTION 7 EARTHWORKS
SECTION 8 GEOTECHNICAL WORKS
SECTION 9 CARRIAGEWAYS: SUB-BASE MATERIAL AND BITUMINOUS
MATERIALS
SECTION 10 CONCRETE CARRIAGEWAYS
SECTION 11 MISCELLANEOUS ROADWORKS
SECTION 12 TRAFFIC SIGNS, ROAD MARKINGS AND ROAD STUDS
SECTION 13 WORK FOR ELECTRICAL AND MECHANICAL
INSTALLATIONS
SECTION 14 WATER SUPPLY PIPEWORKS

VOLUME 2 STRUCTURAL ENGINEERING WORKS

SECTION 15 NOT USED
SECTION 16 ABBREVIATIONS, STANDARDS AND GENERAL –
STRUCTURES
SECTION 17 PILING WORKS
SECTION 18 FORMWORK AND FINISHES TO CONCRETE
SECTION 19 STEEL REINFORCMENT
SECTION 20 CONCRETE AND JOINTS IN CONCRETE
SECTION 21 PRESTRESSING
SECTION 22 STEELWORK
SECTION 23 BRIDGEWORKS
SECTION 24 WATER RETAINING STRUCTURES

VOLUME 3 ARCHITECTURAL WORKS

SECTION 25 NOT USED
SECTION 26 MASONRY AND BLOCKWORK
SECTION 27 WATERPROOFING AND TANKING
SECTION 28 ROOFING AND WALL CLADDING
SECTION 29 CURTAIN WALLING
SECTION 30 INTERNAL CLADDING SYSTEMS
SECTION 31 CARPENTRY AND JOINERY
SECTION 32 GLAZING, GLAZED SCREENS, BALUSTRADES AND
HANDRAILS
SECTION 33 LININGS, SHEATHINGS, DRYWALL PARTITIONS AND
TOILET CUBICLES
SECTION 34 SUSPENDED CEILINGS

Issue No. 4: January 2004 - i -
General Materials & Workmanship Specification
GENERAL MATERIALS AND WORKMANSHIP SPECIFICATION

TABLE OF CONTENTS (CONT’D)

VOLUME 3 ARCHITECTURAL WORKS

SECTION 35 ARCHITECTURAL METALWORK (INCLUDING METAL
DOORS AND SHUTTERS)
SECTION 36 IRONMONGERY
SECTION 37 HARD FLOOR FINISHES
SECTION 38 FLEXIBLE FLOOR FINISHES
SECTION 39 WALL FINISHES
SECTION 40 PAINTING AND DECORATION
SECTION 41 FIRE PROTECTION AND FIRE STOPPING SYSTEMS
SECTION 42 SIGNAGE

VOLUME 4 ELECTRICAL AND MECHANICAL WORKS

SECTION 43 NOT USED
SECTION 44 ABBREVIATIONS, STANDARDS AND GENERAL –
ELECTRICAL AND MECHANICAL
SECTION 45 ELECTRIC POWER SUPPLY
SECTION 46 LOW VOLTAGE SWITCHBOARDS
SECTION 47 SUB-MAINS ELECTRICAL DISTRIBUTION EQUIPMENT
SECTION 48 WIRING AND CABLES
SECTION 49 CABLE MANAGEMENT SYSTEMS
SECTION 50 WIRING ACCESSORIES AND MISCELLANEOUS
ELECTRICAL EQUIPMENT
SECTION 51 GENERAL LIGHTING SYSTEMS
SECTION 52 UNINTERRUPTIBLE POWER SUPPLY SYSTEM (UPS)
SECTION 53 MOTORS
SECTION 54 HIGH VOLTAGE ELECTRICAL SERVICES
SECTION 55 NOT USED
SECTION 56 NOT USED
SECTION 57 EARTHING AND BONDING SYSTEM
SECTION 58 LIGHTNING PROTECTION SYSTEM
SECTION 59 ELECTROMAGNETIC COMPATIBILITY
SECTION 60 INSPECTION, TESTING AND COMMISSIONING
ELECTRICAL SYSTEMS
SECTION 61 AIR HANDLING UNITS
SECTION 62 FAN COIL UNITS
SECTION 63 FANS
SECTION 64 SPLIT TYPE AIR CONDITIONING UNIT
SECTION 65 WINDOW TYPE AIR CONDITIONING UNIT
SECTION 66 AIR COOLING COILS
SECTION 67 DAMPERS AND AIR VOLUME CONTROL DEVICES
SECTION 68 REGISTERS, DIFFUSERS AND GRILLES
SECTION 69 AIR FILTERS
SECTION 70 DUCTWORK AND FITTINGS
SECTION 71 WATER HANDLING EQUIPMENT
SECTION 72 PIPEWORK, FITTINGS AND VALVES
SECTION 73 THERMAL INSULATION

Issue No. 4: January 2004 - ii -
General Materials & Workmanship Specification
GENERAL MATERIALS AND WORKMANSHIP SPECIFICATION

TABLE OF CONTENTS (CONT’D)

VOLUME 4 ELECTRICAL AND MECHANICAL WORKS

SECTION 74 SOUND ATTENTUATORS
SECTION 75 NOISE AND VIBRATION CONTROL
SECTION 76 ELECTRICAL EQUIPMENT AND INSTALLATION
SECTION 77 AUTOMATIC CONTROLS
SECTION 78 INSTRUMENTS
SECTION 79 TESTING, INSPECTION AND COMMISSIONING
SECTION 80 AUTOMATIC SPRINKLER SYSTEM
SECTION 81 HYDRANT AND HOSE REEL SYSTEM
SECTION 82 GASEOUS FIRE EXTINGUISHING SYSTEM (FM200)
SECTION 83 FIRE ALARM AND DETECTION SYSTEM
SECTION 84 PORTABLE HAND HELD EQUIPMENT
SECTION 85 VISUAL FIRE ALARM
SECTION 86 EXIT SIGN AND DIRECTIONAL SIGN
SECTION 87 PIPEWORK, VALVES AND FITTINGS
SECTION 88 PUMPS AND TANKS
SECTION 89 ELECTRICAL EQUIPMENT AND INSTALLATION
SECTION 90 INSPECTION, TESTING AND COMMISSIONING – FIRE
SYSTEMS
SECTION 91 FOUL WATER DISPOSAL
SECTION 92 STORM WATER DISPOSAL
SECTION 93 WATER SUPPLY
SECTION 94 HOT WATER SUPPLY SYSTEM
SECTION 95 PIPEWORK, FITTINGS AND VALVES
SECTION 96 TOWN GAS RETICULATION
SECTION 97 PUMPS AND TANK LEVEL CONTROLS
SECTION 98 ELECTRICAL EQUIPMENT AND INSTALLATION
SECTION 99 INSPECTION, TESTING AND COMMISSIONING –
HYDRAULIC SERVICES
SECTION 100 GENERAL BUILDING MANAGEMENT SYSTEM
SECTION 101 MECHANICAL BUILDING MANAGEMENT SYSTEM
SECTION 102 VOICE AND DATA CABLING
SECTION 103 PUBLIC ADDRESS SYSTEM
SECTION 104 ACCESS CONTROL SYSTEM
SECTION 105 TRUNKED MOBILE RADIO SYSTEM
SECTION 106 CLOSED CIRCUIT TELEVISION SYSTEM
SECTION 107 MASTER ANTENNA TELEVISION (MATV)
SECTION 108 INSPECTION, TESTING AND COMMISSIONING SYSTEM

Issue No. 4: January 2004 - iii -
General Materials & Workmanship Specification
[this page not used]
GENERAL MATERIALS AND WORKMANSHIP SPECIFICATION

VOLUME 1 – CIVIL ENGINEERING WORKS

SECTION 1 ABBREVIATIONS, STANDARDS AND GENERAL

1.1 Definitions and Abbreviations
1.2 Relevant Codes and Standards

SECTION 2 TEMPORARY WORKS

2.1 Introduction
2.2 Design and Performance Criteria

APPENDIX A2.1 TEMPORARY WORKS DESIGN CRITERIA

A2.1.1 Preamble
A2.1.2 Ground Movement
A2.1.3 Ground Water
A2.1.4 Construction Method
A2.1.5 Loads and Forces
A2.1.6 Excavation
A2.1.7 Design Life
A2.1.8 Cofferdams and Temporary Retaining Walls
A2.1.9 Temporary Decks and Pedestrian Bridges
A2.1.10 Falsework
A2.1.11 Formwork
A2.1.12 Earthworks

APPENDIX A2.2 CERTIFICATION OF THE DESIGN OF TEMPORARY WORKS

APPENDIX A2.3 CERTIFICATION OF LOADING, DISMANTLING OR
REMOVAL OF TEMPORARY WORKS

SECTION 3 SITE CLEARANCE AND DEMOLITION

3.1 General
3.2 Relevant Codes and Standards
3.3 Submissions
3.4 Workmanship
3.5 Inspection

SECTION 4 LANDSCAPE SOFTWORKS AND ESTABLISHMENT WORKS

4.1 General
4.2 Definitions and Abbreviations
4.3 Relevant Codes and Standards
4.4 Materials
4.5 Submissions
4.6 Workmanship
4.7 Inspection, Testing and Commissioning

APPENDIX A4.1 BRITISH STANDARDS PUBLICATIONS

Issue No. 4: January 2004 (i)
General Materials & Workmanship Specification
SECTION 5 FENCING

5.1 General
5.2 Design and Performance Criteria
5.3 Materials
5.4 Submissions
5.5 Workmanship

SECTION 6 DRAINAGE WORKS

6.1 General
6.2 Glossary of Terms
6.3 Materials
6.4 Submissions
6.5 Workmanship
6.6 Inspection, Testing and Commissioning

APPENDIX A6.1 CCTV INSPECTION OF PIPELINES

A6.1.1 Scope
A6.1.2 Equipment
A6.1.3 Procedure
A6.1.4 Recording of Results

APPENDIX A6.2 DETERMINATION OF THE COMPACTION FRACTION
VALUE OF AGGREGATES FOR GRANULAR BED

A6.2.1 Scope
A6.2.2 Apparatus
A6.2.3 Procedure
A6.2.4 Calculation
A6.2.5 Reporting of Results

APPENDIX A6.3 DETERMINATION OF THE RESISTANCE TO FRACTURE OF
MANHOLE COVRS AND GULLY GRATINGS
A6.3.1 Scope
A6.3.2 Equipment
A6.3.3 Procedure
A6.3.4 Reporting of results

APPENDIX A6.4 TESTS ON GRAVITY PIPELINES FOR DRAINAGE WORKS

A6.4.1 Scope
A6.4.2 Equipment
A6.4.3 Procedure: Before Tests and Inspections
A6.4.4 Procedure: Water Test
A6.4.5 Procedure: Air Test
A6.4.6 Procedure: Visual Inspection
A6.4.7 Procedure: Infiltration Test
A6.4.8 Calculation
A6.4.9 Reporting of results

Issue No. 4: January 2004 (ii)
General Materials & Workmanship Specification
APPENDIX A6.5 TESTS ON PRESSURE PIPELINES FOR DRAINAGE WORKS

A6.5.1 Scope
A6.5.2 Equipment
A6.5.3 Procedure
A6.5.4 Calculation
A6.5.5 Reporting of Results

SECTION 7 EARTHWORKS

7.1 Definitions and Abbreviations
7.2 Materials
7.3 Submissions
7.4 Workmanship
7.5 Inspection, Testing and Commissioning

APPENDIX A7.1 TEST METHODS FOR FILL MATERIAL

A7.1.1 General
A7.1.2 Terms and Symbols
A7.1.3 Grouping of Material

APPENDIX A7.2 DETERMINATION OF THE MOISTURE CONTENT OF FINE
GRAINED AND MEDIUM GRAINED MATERIAL BY THE
MICROWAVE OVEN DRYING METHOD

A7.2.1 Scope
A7.2.2 Apparatus
A7.2.3 Procedure
A7.2.4 Calculation
A7.2.5 Reporting of Results

APPENDIX A7.3 DETERMINATION OF THE IN-SITU BULK density AND THE
IN-SITU DRY DENSITY OF FINE GRAINED AND MEDIUM
GRAINED MATERIAL BY THE NUCLEAR DENSOMETER
METHOD

A7.3.1 Scope
A7.3.2 Apparatus
A7.3.3 Procedure: Comparability of Test Methods
A7.3.4 Procedure: Routine Denosometer Check
A7.3.5 Procedure: Determination of In-situ Bulk Density
A7.3.6 Calculation
A7.3.7 Reporting of Results

APPENDIX A7.4 DETERMINATION OF THE MAXIMUM CONVERTED BULK
DENSITY BY THE HILF METHOD

A7.4.1 Scope
A7.4.2 Apparatus
A7.4.3 Procedure
A7.4.4 Calculation
A7.4.5 Reporting of Results

Issue No. 4: January 2004 (iii)
General Materials & Workmanship Specification
APPENDIX A7.5 ADJUSTMENT OF THE MAXIMUM CONVERTED BULK
DENSITY FOR THE DETERMINATION OF THE RELATIVE
COMPACTION

A7.5.1 Scope
A7.5.2 Apparatus
A7.5.3 Procedure
A7.5.4 Calculation
A7.5.5 Reporting of Results

SECTION 8 GEOTECHNICAL WORKS

8.1 General Requirements
8.2 Trials for Geotechnical Works
8.3 Definitions and Abbreviations – Ground Investigation
8.4 Submissions – Ground Investigation
8.5 Workmanship – Ground Investigation
8.6 Inspection, Testing and Commissioning – Ground Investigation
8.7 Materials – Slope Treatment Works
8.8 Submissions – Slope Treatment Works
8.9 Workmanship – Slope Treatment Works
8.10 Inspection, Testing and Commissioning – Slope Treatment Works
8.11 Definitions and Abbreviations – Grouting for Geotechnical Works
8.12 Materials – Grouting for Geotechnical Works
8.13 Submissions – Grouting for Geotechnical Works
8.14 Workmanship – Grouting for Geotechnical Works
8.15 Inspection, Testing and Commissioning – Grouting for Geotechnical Works
8.16 Definitions and Abbreviations – Groundwater Drainage and Control
8.17 Materials– Groundwater Drainage and Control
8.18 Submissions – Groundwater Drainage and Control
8.19 Workmanship – Groundwater Drainage and Control
8.20 Inspection, Testing and Commissioning – Groundwater Drainage and Control
8.21 Definitions and Abbreviations – Geotechnical Instrumentation
8.22 Materials – Geotechnical Instrumentation
8.23 Submissions – Geotechnical Instrumentation
8.24 Workmanship – Geotechnical Instrumentation
8.25 General – Laboratory Work
8.26 Workmanship – Laboratory Work
8.27 Inspection, Testing and Commissioning – Laboratory Work

APPENDIX A8.1 “GEO” PROBE TEST

A8.1.1 Scope
A8.1.2 Apparatus
A8.1.3 Procedure
A8.1.4 Reporting of Results

APPENDIX A8.2 DETERMINATION OF THE FLOW OF GROUT

A8.2.1 Scope
A8.2.2 Apparatus
A8.2.3 Procedure: Calibration
A8.2.4 Procedure: Flow Test
A8.2.5 Calculation
A8.2.6 Reporting of Results

Issue No. 4: January 2004 (iv)
General Materials & Workmanship Specification