chevrolet parts and accessories catalog

239 Pages·2007·12.17 MB·English

CHEVROLET PARTS AND ACCESSORIES CATALOG
YEAR MODEL DESCRIPTION PART NO. LIST
NO. USED PRICE
4.003 TRANSMISSION ASSEMBLY (less hand brake)
3-SPD. TRANSMISSION
48-54 COMM .......................... (see NOTE 1)..................... 3845029 1 146.50
NOTE 1: On 1948-53 '2 TON models, replace speedo. drive gear w/3695417. On
1948-54 3/4 TON models replace speedo. drive gear w/3692234. On
1948-53 '/4 TON models replace "U" joint w/5914646. On 1954 TON
models replace "U" joint, trans. rear bearing support assy. and hex
head bolt ('/e-24 x 1'/6) and use 3845019 rear bearing support assy.,
3845092 "U" joint front yoke and hex head bolt ( _24 x 1'4).
49-54 PASS . ......................... (see NOTE 2)...................... 3709812 1 132.25
NOTE 2: On 1949 Pass. models with 3.70 axle, it will be necessary to
replace speedo. drive gear and speedo. driven gear fitting assy.
w/3692233 speedo. drive gear unit. On 1949-52 Pass. models, it
will be necessary to replace speedo. drive gear and speedo. driven
gear fitting assy. w /3695417 speedo. drive gear unit.
55-57 PASS. (close ratio) (2nd design) ... .............................. 3736755# 1 138.25
#NOTE: When installing on 1955 and early 1956 models, 2nd and 3rd. shifter rod
3728286 (4.035) must also be used.
55-59 ',; TON,
60-62 Ser. 20 (D-D) ................... (see NOTE 5...................... 3799187 1 147.50
NOTE 5: When replacing transmission the speedo. driven gear may have to be
replaced with 3845071 for 1955-58 and 3756902, 3756904 or
3756906 for 1959. Also both 1st and reverse, 2nd and 3rd shifter
shaft and plate assy. or the trans. cover assy. will have to be
transferred from the old trans.
55-56 CORVETTE (8 cyl.) ............. (see NOTE 6). .................... 3731933 1 150.50
NOTE 6: When installing on 1956 models with 3.27 axle ratio, the speedo.
driven gear and shaft assy. 3726645 must be used in place of
speedo. driven gear 3708142.
55-57 PASS. (6 cyl.) .................. (see NOTE 4).. ................... 3740406 1 132.25
NOTE 4: When replacing transmission, it will be necessary to install
3845093 1st and reverse lever, 3728300 2nd and 3rd or transfer old
ones. Also, transfer of trans. control cross shaft bracket and
attaching bolts will be necessary.
55-59 'z TON (exc. O/D) ............... (see NOTE 11)..................... 3747000 1 146.50
NOTE 11: When replacing on 1955 models w/6 cyl. engines, both the 1st and
reverse, the 2nd and 3rd shifter shaft and plate assys. or the trans.
cover assy. will have to be transferred from the old transmission.
When replacing on 1955 (1st design) models with 8 cyl. engine,
the shifter shaft levers will have to be transferred from the old
transmission.
57-60 CORVETTE .................... (see NOTE 12)..................... 3748560 1 155.00
NOTE 12: When using on models with Positraction (4.56 axle), speedo. driv gear 3845079
and speedo. driven gear 3845071 must be used.
58 PASS. (6 cyl.) (exc. O/D) ........ .................................... 3741961 1 132.25
58 PASS. (283) (exc. O/D) .......... .................................... 3741451 1 138.25
58 PASS. (348) . ................... .................................... 3746749 1 138.25
59 PASS. (6 cyl.) (exc. O/D, 3.70 axle),
60-61 PASS. (6 cyl.) (exc. TAXI,
3.70 axle, O/D),
62 PASS. (6 cyl.) (exc. TAXI,
POLICE, 3.55, 3.70 axle, O/D),
63 PASS. (6 cyl.) (exc. O/D, 3.55
axle),
64 PASS. (6 cyl.) (exc. POLICE,
##NOTTAEX: I,MOa/iDns)h.a.ft. .h.a.s. 2.7. .s.p.l.in.e.s.... .................................... 3837545## 1 139.75
©-1967
Chevrolet Motor Division 4.003
General Motors Corporation 583
59 PASS. (348),
60 PASS. (w/H/Per., Spec. H/Per.),
60-61 PASS. (283) (exc. O/D),
61 PASS. (348),
61-63 PASS. (409) (exc. 4.11 axle),
62-64 PASS. (327, 409) ................ .................................... 3837553T 1 139.75
tNOTE: When using in place of 3820509 the original clutch gear bearing retainer must be used;
when using in place of 3775641, 3813393 or 3820511, the original 1st and reverse lever
must be reused; when using in place of 3755883 or 3770463 the original cover assy.
must be reused; when using on models prior to 1964 it will be necessary to use 3868649
yoke assy.; when using in place of 3755779 or 3774999 the original shifter shaft, plate
assemblies and levers must be reused.
59 PASS. (283) (exc. O/D) .......... .................................... 3755883 1 138.25
60 PASS. (348) (exc. H/Per., Sp.
H/Per.) ...................... .................................... 3770471 1 139.75
60 Ser. 10 (w/3.90 axle) (exc. 4/WD) . .................................... 3782117 1 147.50
60 Ser. 20 (exc. D-D) ............... 3782121 1 147.50
61 CORVETTE (exc. P/Trac.),
.................... ....................................
62 CORVETTE 3813391 1 155.00
61-62 Ser. 10 w/3.90 axle (exc. 4/WD),
61-63 4/WD (1st Ser.) ................. .................................... 3799183 1 147.50
61-62 Ser. 20 (exc. D-D) ............... .................................... 3799185 1 147.50
62-64 PASS. (283) (exc. O/D),
.......... ....................................
64 POLICE, TAXI (6 cyl.) 3837547♦ 1 139.75
♦NOTE: When using on 1962 and 1963 models it will be necessary to use 3868649
Yoke in group 5.555.
.................... ....................................
63 CORVETTE 3839715 1 155.00
63 Ser. 10 w/3.73 axle,
63 4/WD (2nd Ser.),
....................................
63 Ser. 20 (exc. D-D, 4/WD) ......... 3830205 1 147.50
63 Ser. 20 (D-D) ................... ................................... 3830209 1 147.50
64-65 G-10 ........................... ................ 3866699e 1 147.50
®NOTE: When using on 1st design 3846282, it will be necessary to use 3707059
Sleeve Yoke Assy.
.................... ....................................
64-65 CORVETTE 3866695** 1 155.00
*NOTE: When using on 1964 models, 3868728 "U" joint front yoke assy. must
be used if original yoke will not slide over splines of new shaft.
....................................
64-67 Ser. 10-20 (exc. O/D 3.07 axle) ... 3895794 1 141.00
65 PASS. (6 cyl.) (exc. TAXI,
....................................
POLICE, O/D, 3.55 axle) ...... 3854720 1 139.75
65 PASS. w/3.55 axle (6 cyl.) (exc.
STA. WAG.) .................. .................................... 3854721 1 139.75
65 PASS. (327) .................... .................................... 3854724 1 139.75
65 PASS. (8 cyl.) (exc. 327, O/D),
................ ....................................
65 POLICE (6 cyl.) 3854722 1 139.75
66-67 PASS. (exc. O/D, 327),
67 Ser. 10-20 (Saginaw) (exc. D-D,
4/WD) ........................ .................................... 3860040 1 139.75
66-67 PASS. (327) (exc. 3.55, 3.70 axle),
.................... ....................................
67 CORVETTE 3860097 1 139.75
.................... ....................................
66 CORVETTE 3873887 1 155.00
66 Ser. 10-20 (exc. D-D, 4/WD,
3.07 axle) .................... .................................... 3873898 1 147.50
............... ...................:................
66-67 G-10-20 (Saginaw) 3887017* 1 147.50
*NOTE: Not used with 7.00 x 14, 7.35 x 13 tires unless 3.73, 4.11 axles are used.
H.D. 3-SPD. TRANSMISSION
55 TON (1st Ser.),
55-59 Ser. 3 (2nd Ser.),
.................. .....................
60-66 Ser. 10 thru 30 (see NOTE 3) 3839637 1 189.50
NOTE 3: When using on a vehicle previously equipped with a propeller shaft
parking brake, transfer the mainshaft rear bearing retainer assy., the
"U" joint front flange assy. (including the speedometer drive gear)
and the balance of the propeller shaft brake parts from the original
transmission. When it is used on a 1954-1959 model or a 1955-1963
D-D model, it will be necessary to replace both outer shifting
levers with levers from the original transmission. Also, when it is
used on a 1960 model (exc. D-D), it will be necessary to replace the
outer 2nd and 3rd shifting lever with the lever from the original
transmission.
w .......................
65-68 PASS . ......................... /extension 3890533 1 199.50
4.003 C-1967
Chevrolet Motor Division
584 General Motors Corporation
4-SPD. TRANSMISSION
48-55 COMM., UTIL. (.1st Ser.),
55-59 Ser. 3 (2nd Ser.),
60-66 Ser. 10 thru 30 .................. (less prop. shaft brake) ............. 3837561(( 1 220,00
§NOTE: When using on past models it may be necessary to remove rear
bearing retainer assy. and retainer gasket which can be found in
groups 4.317 and 4.318 respectively.
63 PASS., CORVETTE (327),
64 PASS., CORVETTE ............. (2.56 to 1 ratio) , , , , , , , , , , , , , , , , , , , , 3867265 tAAI 282.70
ttNOTE: When using on 1963 models it is necessary to use the 1964 clutch housinc.
AANOTE: When using on 1963 models transfer old shifter levers or install
new levers.
64 PASS. w/4.1 1 axle,
64 CORVETTE w/F.I. (exc. P/Trac.) (2.20 to 1), , , , , , , , , , , , , , , , , , , , , , , , , 3867268* 1 282.70
64 PASS. (8 cyl.) (exc. 4.11, 4.56
P /Trac. ),
64 CORVETTE w/P/Trac. (exc.
4.56) ........................ (2.20 to 1)......................... 3867267* 1 282.70
*NOTE: Less levers.
64 PASS., CORVETTE w/4.56
P/Trac ....................... (2.20 to 1)........................ 3867269 1 282.70
65 PASS. (exc. close ratio),
65 CORVETTE (exc. close ratio,
Sp. H/Per., F.I., 396),
66-67 PASS., CORVETTE (exc. close
ratio) ........................ (2.52 to 1) (aluminum)..,............ 3870357 1 282.70
65 CORVETTE w/327 Sp. H/Per.,
F.L, 3.70, 4.11 axle,
65-66 PASS. (close ratio) w/4.10,
3.73 axle,
65-67 CORVETTE (close ratio)
w/P/Trac„ 3.70, 4.11 axle
(427),
65-67 PASS. (close ratio) w/P/Trac.
(exc. 8.15 x 15 tires) .......... (2.20 to 1) (aluminum) .............. 3880853 1 282.70
ONOTE: It may be necessary to transfer all original outer shift levers.
65 PASS. w/3.55 axle (8 cyl.) (exc.
close ratio),
66-67 CORVETTE w /P/Trac. (327
Sp. H/Per.) (exc. close
ratio) ........................ (2.52 to 1) (aluminum)............... 3890534 1 301,40
65 CORVETTE (P/Trac. w/3.08,
3.36, 3.55 axle) (F.I., 327
Sp. H/Per.),
65 CORVETTE (396),
65 PASS. (close ratio) (exc. P/Trac.),
66 CORVETTE (close ratio)
w/3.55, 3.36 axle (427 Sp.
H,/Per.),
66-67 PASS. (close ratio) (exc. P/Trac.,
3.73 axle),
67 CORVETTE (427) (exc. P/Trac.
w'3.70, 4.11 axle) ............. (2.20 to 1) (aluminum)............... 3879669 1 282.70
66 PASS. (327) .................... (2.54 to 1) (cast iron) ............... 3884603 1 282.70
66-67 PASS. (283) (exc. 3.55 axle,
close ratio),
66-67 PASS, w/3.55 axle, 8.15 x 15 tires
(exc. close ratio )................... ((33..1111to 11) (cast iron) ............... 3916103 1
67 Ser. 10 thru 30 (exc. 6.17 rear axle) .................................... 3917771 1 265.95
67 Ser. 30 w /6.17 rear axle .......... .................................... 3917772 1 265.95
H.D. 4-SPD. TRANSMISSION
65-67 CORVETTE (396 Sp. H/Per., 427)
(exc. P/Trac.),
65 PASS. (396 Sp. H/Per.,427) (exc.
P/Trac.),
66-67 PASS. (427 Sp. H/Per.) (exc.
P/Trac.) ..................... (2.20 to 1) (aluminum) ............... 3925614 1 375.00
67 Ser. 10,,,,,,,,,,,,,,,,,,,,,,,,, (New Process 98313),,,,,,,,,, ,,,,, 3906341 1 295.00
67 Ser. 20-30 ...................... (New Process 98330) ............... 3906342 1 295.00
.6-1967
Chevrolet Motor Division 4.003
General Motors Corporation 585
POWERGLIDE TRANSMISSION
62 PASS. (327) (exc. H/Per.) ........ .................................... 3788887 1 282.70
63 PASS. (6 cyl.) (exc. TAXI, S.S.,
3.55 axle),
64 PASS. (6 cyl.) (exc. TAXI,
POLICE) ..................... .................................... 3844240 1 269.00
63-64 PASS. (283) (exc. S.S., TAXI,
3.55 axle) .................... .................................... 3844242 1 282.70
63 PASS. (327) (exc. S.S., H/Per.,
POLICE),
64 PASS. (327) (exc. H/Per., POLICE) .................................... 3831949A 1 282.70
ANOTE: When using on 1963 models, it will be necessary to retain shift levers.
64 PASS. (409) .................... .................................... 3832581 1 282.70
64-66 Ser. 10-20 (exc. D-D, 327, 7.00 x
16, 7-17.5 tires),
64-66 Ser. 10 (D-D) (230) (exc. 6.50 x
16, 7.00 x 15 tires) ............ .................................... 3884618 1 282.70
64-66 Ser. 10-20 w/7.00 x 16, 7-17.5
tires) (exc. D-D, 327),
64-66 Ser. 10 (D-D) w/6.50 x 16, 7.00 x
15 tires (230) ................. .................................... 3884619 1 299.50
65 PASS. (6 cyl.) (exc. oil cooler,
3.55 axle) .................... .................................... 3848977 1 282.70
65 PASS. (6 cyl.) w/oil cooler, 3.55
axle......................... .................................... 3857265 1 282.70
65-66 G-10 (230) ...................... .................................... 3879982 1 299.50
65 PASS. (327 H/Per.) (exc. POLICE),
65 TAXI (327),
66 PASS. (327),
67 PASS. (327) (exc. A.I.R.) ......... .................................... 3887075 1 282.70
65-66 PASS. (283) .................... .................................... 3848982 1 282.70
65-67 CORVETTE (327) ............... .................................... 3887071 1 282.70
66-67 PASS. (6 cyl.) (exc. 3.70 axle) .... ................... ................ 3887072 1 282.70
67 PASS. (283) .................... .................................... 3887074 1 282.70
67 PASS. (396) .................... .................................... 3887076 1 282.70
67 G-10-20 (exc. 230) ............... .................................... 3887009 1 299.50
67 Ser. 10-20 (exc. 327, D-D) ........ .................................... 3887086 1 282.70
68 G-10-20 (6 cyl.) (exc. 250) ........ .................................... 3919368t 1
68 Ser. 20 (D-D) (292) .............. w/6 bolt converter .................. 3919373 1
68 Ser. 20 (D-D) (6 cyl.) (exc. 292) ... w/3 bolt converter .................. 3919374 1
68 Ser. 10-20 (C ONV.)(8 cyl.) ....... .................................... 3919378# 1
68 Ser. 20 (D-D) (8 cyl.) ............ .................................... 3920706 1
tNOTE: Not used with 3.73; 4.11 axle on G-10 (6 cyl.) unless 6.95 x 14, 7.00 x 14, 7.35 x 14
tires are used.
#NOTE: Not used with 4:11 axle on Ser. 10. unless 6.50 x 16, 7.00 x 15, 7.75 x 15, 8.15 x 15
tires are used.
TURBO-HYDRAMATIC TRANSMISSION
65-66 PASS. (396) .................... .................................... 8626005 1 377.60
66-67 Ser. 10-20 ...................... .................................... 8626045 1 400.00
67 PASS. (396) .................... .................................... 8626025 1 377.60
TURBOGLIDE TRANSMISSION
57 PASS . ......................... .................................... 3764001 1 219.50
58-61 ALL ........................... (see NOTE 13) P.G. Conversion Unit . 3832566 1 219.50
NOTE 13: When using on 1958 models, it will be necessary to order 3750748 propeller shaft.
HYDRAMATIC TRANSMISSION
55-57 ALL (2nd Ser.) (exc. O.C., '/ TON),
58-59 ALL (6 cyl.) (exc. O.C.) ......... w/prop. shaft brake (see NOTE 8) .... 8618685 1 421.25
NOTE 8: When using 8618685 on Ser. 3E 1st design 1958 and prior models it
will also be necessary to use 2330592 filler tube, 2324603 indicator
assy. and 3752135 clamp. On D-D models 1st design 1958 and prior
models it will also be necessary to use 2334864 filler tube,
2334854 indicator assy. and 3752559 clamp. Also, on L6 engines,
it may be necessary to drill 5/6 hole through flywheel housing.
4.003 ©-1967
Chevrolet Motor Division
586 General Motors Corporation
55-57 ALL w/O.C. (2nd Ser.) (exc.
'z TON),
58-59 ALL w/O.C. (6 cyl.) (exc.
'2 TON),
60-62 D-D ........................... w/prop. shaft brake (see NOTE 9) .... 8618555 1 429.50
NOTE 9: When using 8618555 on 1st design 1958 and prior models it will be
necessary to use 2330592 filler tube, 2324603 indicator assy.,
3752135 clamp, 8526789 oil cooler. Cut oil cooler pipes from 5/6
steel tubing part 3830292 as required and assemble 137398 nut to
both ends before flaring. Also, on L-6 engines, it may be necessary
to drill a S,6 hole through flywheel housing.
REBUILT TRANSMISSIONS
NOTE: For 1958 to 1961 Turboglide Conversion unit, see the main section of this group.
55-57 ALL w/P.G. (6 cyl.) ............ ....................................
55-57 ALL w/P.G. (8 cyl.) ............. .................................... 3832562 1 99.50
58-62 ALL w/P.G. (6 cyl.) .. . . . . . . . . . . . .................. . ................. 3832563 1 138.50
58-62 ALL w/P.G. (8 cyl.) (exc. 327) .... .................................... 3832564 1 138.50
3832565 1 138.50
4.004 KIT-CONTROL ASSY.-CONVERSION UNIT, Transmission Gearshift
38-39 PASS., COMM.,
40-47 COMM. w/3-SPD ................ gearshift lever ..................... 609928* 1 1.79
*NOTE: Consists of. .1. H..a.g..., .1. .S.e.a.t., 1 Spring, 1 Gasket, 1 Ball Retainer.
38-53 PASS. (exc. P.G.) thrust washer and needle brg......... 3692617t 1 1.70
tNOTE: Consists of 1-591793 Washer, 2-590826 Washer, 2-591091 Washer, 14- 435844 Roller,
1953 Models also require 24-7450247 Roller.
41-54 PASS., COMM. w/3-SPD. H.D.,
................
54 PASS. w/3-SPD . thrust washer and needle brg......... 3711626# 1 4.45
#NOTE: Consists of 1-591793 Washer, 2-591091 Washer, 3-3845097 Washer, 14- 435844 Roller,
50-435847 Roller. 1953-54 Models also require 24-7450247 Roller.
...............
55 PASS. (exc. P.G.) control lever repair................. 3731061® 1 3.44
®NOTE: Consists of 1 each of 3732059 lever, 3732060 lever, 3732312 ring, 3725633 spacer,
3726338 seat.
55-57 PASS. w/3-SPD.,
55-59 COMM. w/3-SPD. (exc. H.D.),
60-62 Ser. 10-20 w/3-SPD. (exc. H.D.)... thrust washer and needle brg......... 3725035t 1 7.45
:NOTE: Consists of 2-3845097 Washer, 1-3736753 Washer, 2-591091 Washer, 14-435844 Roller,
50-435847 Roller, and 24-7450247 Roller.
58-63 PASS., CORVETTE w/3-SPD. .... thrust washer and needle brg......... 3838375 1 7.90
63-66 Ser. 10-20 w/3-SPD. (exc. H.D.),
67-68 Ser. 10-20 w /Muncie 3-SPD. (exc.
....................
O.D. 292)
thrust washer and needle bearing ..... 3832139 1 7.20
6664--6685 PPAASSSS..,, C COORRVVEETTTTEE, G w-1/30--S20PD. .... thrust washer and needle brg......... 3858809 1 6.90
w /3-SPD, (exc. H.D.),
66-68 Ser. 10 w O.D.,
4687--5628 'S,z,er3/., 1T0O-N20, w/Saginaw 3/SPD. ..... thrust washer and needle bearing ..... 3886339 1 4.35
4593-54 P',,A,S'Siq .TO..N. .(e.x.c....D.-.D.)......................... CONTROL ASSY., w/shaft and housing 3686801 1 9.30
CONTROL ASSY., w/shaft and housing 3688157 1 8.80
54-55 COMM. w/3-SPD. (1st Ser.),
5555 SSeerr.. 33 ww//33--SSPPDD.. ((86 ccyyll..)), (2nd Ser.) , CONTROL ASSY., w/shaft and housing 3700376 1 9.30
56-59 Ser. 3 w/3-SPD.,
60-66 Ser. 20-30 (D-D) w/3-SPD.........
555876---666124 CCPAOOSRRS.VV wEE/4TT-STTPEED .ww, //43--SSPPDD........................ CCCOOONNNTTTRRROOOLLL AAASSSSSSYYY...,,, www///llseehvvaeefrrt aaannnddd bbhrroaauccskkineettg.. 333777625029700055276 111 43849...203550
6622--6633 IPMAPSASL. Aw (/S4.-SS.)P wD/.4 (-SexPcD.. S..S...). ............ CCOONNTTRROOLL AASSSSYY..,, ww//lleevveerr aanndd bbrraacckkeett .. 3828658 1 49.95
63 IMPALA (S.S.) w/P.G. ..... (daub of yellow paint) ............... 3828659 1 49.95
6634 CIMOPRAVLEAT (TSE.S w.) /w4-/SPP.GD.. ...................... CCOONNTTRROOLL AASSSSYY..,, ww//lleevveerr aanndd bbrraacckkeett ... 33882274385135 11 3488..5350
6644--6676 CG-O10RwV/3E-STPTDE .w./.3..-S..P.D...................... CCOONNTTRROOLL AASSSSYY..,, ww//lleevveerr aanndd bbrraacckkeett..,. 33885473319204 11 3337..1450
64-66 G-10 w.%P.G ..................... CONTROL ASSY., w/shaft and housing 3888900 1 25.75
6644--6677 CPAOSRSV.EwT/ T4SEP wD /.4-S..P.D... ...................... CCOONNTTRROOLL AASSSSYY..,, bwra/schkaeftt .a.n.d. .h.o.u.s.i.n.g.. 33888481940712 11 2257..7250
CONTROL ASSY„ w/shaft and housing . 3889460 1 34.75
©-1967
Chevrolet Motor Division 4.003-4.004
General Motors Corporation 587
...........
65 IMPALA (S.S.) w/P.G. CONTROL ASSY., w/lever and bracket. 3859850 1 35.40
....................
65 S.S. w,'T.H . CONTROL ASSY., w/lever and bracket. 3870172 1 35.40
..............
65-67 CORVETTE w/P.G CONTROL ASSY., w/lever and bracket.. 3877970 1 35.40
66 PASS. (T.H. wbucket seats) ..... CONTROL ASSY., w/lever and bracket. 3879744 1 35.80
.............
66-67 PASS. (P.G. w /B.S.) CONTROL ASSY., w/lever and bracket.. 3902227 1 35.80
............
67 PASS. (T.H. w 'T.H.) CONTROL ASSY., w/lever and bracket .. 3904027 1 35.80
................
67-68 G-10-20 w /3-SPD CONTROL ASSY., w/shaft and housing 3888928 1 24.75
.................
67-68 G-10-20 w,'P.G . CONTROL ASSY., w/shaft and housing 3888946 1 24.75
...........
68 CORVETTE w/3-SPD. CONTROL ASSY., w/lever and bracket. 3921623 1 39.50
68 CORVETTE w/4-SPD............ CONTROL ASSY., w/lever and bracket.. 3921637 1 39.50
.............
68 PASS. (A.T. w;/B.S.) CONTROL ASSY., w/lever and bracket.. 3922547 1 39.95
..............
68 CORVETTE w TH CONTROL ASSY., w/lever and bracket.. 3921660 1 37.25
................
68 PASS. w '4-SPD . CONTROL ASSY., w/lever and bracket.. 3922514 1 27.75
68 G-10-20 w;'Warner 4-SPD.......... CONTROL ASSY., w/shaft and bracket.. 3924800 1
57-58 CORVETTE w/4-SPD............ CONVERSION UNIT, control........... 3758679 t t 1 12.55
ttNOTE: When components of the old design linkage warrant replacement, the above unit must
be installed. Consists of 1—shaft assy., 3—plates, 2—springs, 1—pin and 1—sleeve.
...........
57-61 CORVETTE w/4-SPD. CONVERSION UNIT, control........... 3749586( 1 47.70
§NOTE: Used when converting from 3-spd. to 4-spd. transmission. Contains control,
ext. linkage and speedo. cable only.
58 PASS., CORVETTE w/P.G. ...... CONVERSION UNIT, thrust washer ..... 3758782A 1 16.75
ANOTE: Required on early 1958 models when it is necessary to replace the low sungear and
flange assy., input shaft or low sungear bearing; Consists of 3755407 Flange Assy.,
3755409 Input Shaft, 3755411 low sungear Bushing and 3755412 Thrust Washer.
4.005 GASKET UNIT—SEAL UNIT—RING UNIT, Transmission
......................
38-47 COMM., UTIL. w/4-SPD.......... (see NOTE 1) 606664 1 1.20
.................. ......................
38-39 ALL w/3-SPD (see NOTE 1) 3689488 1 1.27
......................
40-54 ALL w/ 3-SPD. (exc. H.D.) ....... (see NOTE 1) 3764394 1 1,08
NOTE 1: Consists of bearing retainer gaskets, cover gaskets, "U" joint seal and shims.
48-55 COMM., UTIL. w/4-SPD. (1st Ser.),
55-59 Ser. 3-4 w/4-SPD. (2nd Ser.),
60-67 Ser. 10 thru 30 w/4-SPD. (exc.
................... .....................
close ratio) (see NOTE 15) 3849472 1 .80
NOTE 15: Consists of 1 cover gasket, 1 rr. bearing retainer gasket, 1 power take off cover
gasket, and 3 gear bearing retainer gasket.
.................. ......................
50-52 PASS. w/P.G . (see NOTE 2) 3701030 1 4.01
NOTE 2: Consists of 1 hsg. to case gskt., 1 valve body to case gskt., 2 side cover gskts., 1 rear
oil pump gskt., 1 servo cover gskt., 1 modulator housing gskt., 1 manual valve seal,
1 oil suction pipe seal, 1 valve spring plug gskt., and 1 ball collar seal.
53-54 PASS. w/P.G.,
.................
53-55 CORVETTE w/P.G. (6 cyl.)...... for complete repair 3703919 1 4.20
54-55 COMM. w/3-SPD. H.D. (1st Ser.),
55-59 Ser. 3 w/3-SPD. H.D. (2nd Ser.),
......................
60-66 Ser. 10 thru 30 w 3-SPD. H.D. .... (see NOTE 9) 3723039 1 2.05
NOTE 9: Consists of 1 cover gasket, 3 clutch gear brg. ret. gskts., 1 rear brg. retainer
gasket and 1 oil seal assembly. When using on 1954 models exc. TON,
'/2
3845021 oil seal must be used in place of 591448 seal.
.....................
54-62 ALL w H.T for complete repair (see NOTE 4)..... 3736893 1 5.75
NOTE 4: It will be necessary to use 3689826 "0" ring Seal and 3692836 shims only on
early 1954 '4 Ton jobs. When using on models equipped with prop. shaft brake,
8615618 rear bearing retainer gasket must be used in place of 8611998. Consists
of 1 case frt. cover seal, 1 "U" joint "0" ring seal, 1 torus cover seal, 1 oil
pan plug gasket, 1 oil pan gasket, 1 press, reg. gasket, 1 rear brg. ret. gasket,
1 rear servo body gasket, 1 case side cover gasket and 2 ball collar shims.
55-65 ALL, CORVETTE w/3-SPD. (exc.
O/D, H.D.),
66 Ser. 10-20 w/3-SPD. (exc. H.D.),
67-68 Ser. 10-20 w,'Muncie 3-SPD. (exc.
........................ ......................
O.D.) (see NOTE 7) 3719636 1 .37
NOTE 7: Consists of 1 transmission cover gasket, 1 clutch gear bearing retainer gasket,
1 transmission extension gasket and 1 °'O" ring seal.
55 PASS. w/P.G.,
55 CORVETTE w/P.G. (8 cyl.) (to
.
trans. serial No. C-1231) ....... for complete repair (see NOTE 8).... 3714456* 1 3.54
*NOTE: Use with valve body cast 3709023.
4.004-4.005 c-1967
Chevrolet Motor Division
588 General Motors Corporation
55-56 PASS. w/P.G. (after trans. Serial
No. C-103),
56-57 PASS., CORVETTE w/P.G. ...... for complete repair (see NOTE 8)... , , 3716678t 1 3.68
tNOTE: Use with valve body cast 3719233.
NOTE 8: Consists of 1 gskt. ea. for: valve body to case, hsg. side cover, rr. oil pump, servo
cover, governor cover, hsg. side cover—L.H., low and drive valve and 1 parking lock
lever shaft oil seal and 1 oil pump suction pipe seal.
55-65 PASS., , TON w/O/D,
5676-68 PPAASSSS..,w S/Te.rG. 1.0 .(.C.O..N..Y...). w../O....D....... (osveeer N dOriTveE .1.0.). .......................................... 33795140016147 11 (4.486.04)0
NOTE 10: Consists of 2 "0" ring seals, 1 stator support gasket, 3 square ring seals, 1 front
oil pump seal, 1 brake piston seal unit, 1 neutral clutch seal unit, 1 front pump seal
unit, 1 oil pan drain screw gasket, 1 valve body gasket unit, 1 oil seal assy.
57-63 PASS., CORVETTE w/4-SPD ..... (see NOTE 14) ..................... 3840376 1 4.34
NOTE 14: Consists of 1—trans. cover gasket, 1—clutch gear brg. ret. gasket, 1—front,
1—rear trans. rear brg. ret., 3—"O" ring seals, 1_oil seal assy.
58 PASS. w/T.G . .................. (see NOTE 10) ..................... 3756472 1 8.40
58-62 ALL, CORVETTE w/P.G. (exc. 327) (see NOTE 11) ..................... 3764407 1 3.39
NOTE 11: Consists of 1 case gasket, 1 valve body to case gasket, 1 ea. right and left hsg.
side cover gasket, 1 rr. oil pump gasket, 1 servo cover gasket, 1 governor cover
gasket, 1 oil pump suction pipe seal, 1 body end plate gasket, 1 drive valve body
gasket, 1 parking lock lever shaft oil seal and 2 "0" ring seals.
59-61 PASS. w/T.G . .................. (see NOTE 12) ..................... 3760222 1 8.75
NOTE 12: Consists of 2 "0" ring seals, 3 square ring seals, 1 drain screw gasket, 1 stator
support gasket, 1 frt. oil pump seal, 1 frt. pump seal unit, 1 brake piston seal unit,
1 neutral clutch seal unit, 1 valve body gasket unit, 1 oil seal assy. and 1 vacuum
modulator gasket.
62 PASS., CORVETTE w/P.G. (327),
63-68 ALL, CORVETTE w/P.G......... (see NOTE 13) ..................... 3910040 1 8.45
NOTE 13: Consists of all Gaskets and Seals for complete overhauls, except rear extension
oil seal.
63-66 PASS., CORVETTE w/Muncie
.................. ....
4-SPD (see NOTE 16).................. . , 3849473 1 1.69
65-66 PASS. w/T.H.,
66 Ser. 20 w/T.H ................... (see NOTE 17) ..................... 8624933 1 5.60
NOTE 17: Consists of 4 "0" ring seal, 2 case gaskets and 1 each of the following:
gasket-oil pan, gasket-solenoid valve, gasket-valve body to spacer,
gasket-gov. cover, gasket-rear servo cover, seal-reverse servo piston, seal-Assy.
manual shaft, seal-vacuum mod, and conn., seal-ring case extension, seal-ring
pump to case and 8 washers for pump body bolts.
65-68 PASS. w/3-SPD. H.D.,
68 Ser. 10-20 w/H.D. 3-SPD. ........ (see NOTE 18) ..................... 3870814 1 .55
NOTE 18: Consists of 3 gaskets for the clutch gear brg. retainer and 1 each for trans.
cover, and extension.
65-68 PASS. w/T.H . .................. overhaul ...................... ... 8625904* 1 34.50
ANOTE: Consists of 1 front servo piston oil se al ring, 2 pump oil seal rings,
4 center support oil seal rings, 3 intermediate clutch drive plate assy's.,
5 forward clutch driven plate assy's., 1 front pump seal, 1 extension
housing seal, 2 forward and direct clutch piston seal kits, 1 intermediate
clutch piston seal kit, 1 overhaul gasket and seal kit.
66-68 PASS., CORVETTE, G-10-20
w/3-SPD. (exc. H.D.),
66-68 PASS. w/Saginaw 4-SPD. (283, 327),
66-68 Ser. 10 w/O, D.,
67-68 Ser. 10-20 (CONV.) w/3-SPD. (exc.
O.D.),
6678 SAeLr.L 1w0/N-2e0w ( DPr-oDce)s ws 4/3-S-SPPDD . .............. ........................................................................ 33885896139318 11 1..6506
67-68 PASS., CORVETTE, w/4-SPD..... (see NOTE 16) ..................... 3917763 1 1.69
NOTE 16: Consists of 1 rr. bearing retainer front gasket, 1 rr. bearing retainer rr. gasket,
1 cover gasket and 2 clutch gear bearing retainer gasket.
68 Ser. 10 thru 30 w/4-SPD. (exc. H.D.) ....................................
3930800AA 1
AANOTE: This unit contains all gaskets and seals for complete overhaul.
50-52 PASS. w/P.G . .................. SEAL UNIT, "0" ring (see NOTE 5) ... 3698460 1 2.55
NOTE 5: Consists of 1 converter cover, 1 turbine bolt, 1 frt. pump, 1 "U" joint and 1 primary
pump hub "0" ring seal.
©.-.1 967
Chevrolet Motor Division 4.005
General Motors Corporation 589
53-61 ALL, CORVETTE w/P.G.,
62 PASS. w/P.G. (283),
62 Ser. 10-20 w/P.G. (exc. D-D,
......................
4/W.D.) SEAL UNIT, "0" ring (.120 thk.
62 Ser. 10 (D-D) w/P.G . ............ converter cover seal) (see NOTE 6)... 3814713 1 2.15
NOTE 6: Consists of one seal each for converter cover, ball joint collar, and frt. oil pump body.
............... ...... ...............
67-68 ALL w/T.H SEAL UNIT, w/gaskets 8625905t 1 6.10
ttNOTE: Consists of: 1 ring pump to case seal, 8 o-ring pump body bolt Seals, 8 pump body
bolt washers, 1 pump cover to case gasket, 1 o-ring output shaft seal, 1 reverse
servo piston seal, 1 rear servo cover gasket, 1 governor cover gasket, 1 o-ring
parking pawl shaft seal, 2 manual shaft o-rings, 1 manual shaft seal assy., 2
vacuum modulator and connector seals, 1 valve body to spacer gasket, 1 case
to spacer gasket, 1 solenoid valve gasket, 1 o-ring strainer seal, 1 trans. oil pan
gasket, 1 case extension to case gasket, 1 23/ dia. parking shaft plug.
.............. 64
50-61 ALL w/P.G. (iron) RING UNIT, trans. oil seal (see NOTE
A) ................................ 3928596 1 7.65
NOTE A: Consist of 4 input shaft seals, 2 clutch drum seals, 2 servo piston seals,
1 front pump seal, 1 low servo seal.
.....................
57-61 ALL w/T.G RING UNIT, trans oil seal (see NOTE B) 3928595 1 1.95
NOTE B: Consists of 4 turbine shaft seals (1-3730919), 2 clutch drum seals, 1 stator
piston seal.
62-68 ALL w/P.G. (aluminum).......... RING UNIT, trans. oil seal (see NOTE
C) ................................ 3928592 1 5.85
NOTE C: Consists of 2 input shaft seals, 2 clutch drum seals, 2 governor seals,
.....................
65-68 ALL w /T.H RING UNIT, trans. oil seal (see NOTE
NOTE D: Consists of 6 center support and pump cover seals, 1 front servo piston seal, 1 front
accumulator piston seal, 1 accumulator piston seal, 1 rear accumalator piston seal.
4.006 LEVER—KNOB—HANDLE—BUTTON—CABLE—ROD—COVER,
Gearshift Control (Hand)
38-47 COMM., UTIL. w/4-SPD.
...............
(exc. COE) ................... (w/reverse latch rod) 591216 1 10.60
38-39 PASS. (ctr. shift w/3-SPD.),
................
38-47 COMM. w/3-SPD (27"/6 developed length)............ 591219 1 6.45
39-47 COE .......................... lower (w/cap, spring and cup) ....... 3650879 1 4.30
.............
47 COE .......................... upper (w/reverse cable) 3682882 1 10.95
48-55 COE .......................... lower (811/32 long) ................... 3684588 1 4.40
4$-55 COE .......................... upper (w/ball, spring ret.)........... 3696510 1 9.05
48-53 COMM. w/3-SPD.,
49.52 PASS. w/3-SPD ................. (less grip) ........................ 3686799 1 1.55
46-55 COMM., UTIL. w/4-SPD. (1st Ser.)
(exc. D-D, COE, 2-SPD)
55-59 Ser. 3 w/4-SPD. (2nd Ser.)
(exc. D-D) .................... (231/6 dev. length) ................. 3720367t 1 6.65
t NOTE: On 2-SPD. axle models drill a .126-.130 dia. hole thru lever 3.69 from top of lever for
control bracket stop pin.
.........................
50-52 PASS. w/P.G . ................. . (less grip) 3694329 1 1.13
53-55 CORVETTE w/P.G . ............ . ...............................I.... 3706410 1 9.85
53-54 PASS. (exc. P.G.),
................ .
53-56 COMM. w/ 3-SPD (less grip) ......................... 3723916 1 1.55
53-54 PASS. w/P.G.,
.....................
54-56 ALL w/H.T (w/bushing) (less grip) .............. 3723914 1 2,78
55-57 PASS . ........................ . (less grip) (chrome) ................. 3719852 1 1,89
55-56 CORVETTE w/3-SPD.,
57-63 CORVETTE (exc. P.G.),
61 PASS. w/4-SPD . ............... . .................................... 3760703 1 14.80
.55-64 D-D w/4-SPD. (2nd Ser.) (exc.
102 W.B.),
..........................
58-60 4/WD (37"/4 dev. length) (less grip)........ 3715869 1 7.95
-56-62 CORVETTE w/P.G . ............ . .................................... 3723115 1 11.40
57-59 Ser. 3 (exc, 4-SPD.),
60-64 D-D (exc. 4-SPD., 102 W.B.),
65-67 Ser. 20 (D-D) (exc. 4-SPD.),
65-66 Ser. 30 (D-D) w /3-SPD., H.D.,
67 Ser. 30 (D-D) w/T.H . ............ (105/3z O.L.) ........................ 3716517 1 1.35
58 PASS. w/3-SPD . ............... . .................................... 3741777 1 2.27
58 PASS. w/A.T . ................. . .................................... 3742437 1 1.74
58-61 PASS. w/4-SPD.,
62 S.S. w/4-SPD. (1st design),
62-63 PASS. w/4-SPD. (exc. S.S.) ....... (15'46 O.L.) ........................ 3814110 1 15.00
4.005-4.006 3 -1967
Chevrolet Motor Division
590 General Motors Corporation
68 CORVETTE w/4-SPD ........... control ............................ 3921638 1 13.65
68 Ser. 20-30 (D-D) w/4-SPD. (exc.
H.D.)........................ control ............................ 3922927 1 7.25
68 Ser. 10 (D-D) w/4-SPD. .......... control ........................ ... 3922959 1 7.25
68 PASS. w '4-SPD . ................ control upper ...................... 3924463 1 5.95
68 Ser. 20-30 (D-D) w/G.D. 4-SPD. ... control ............................ 3922955 1 8.75
68 PASS. (A.T. w 'T.W.) (exc. B.S. SS) control ............................ 3928239 1 3.50
68 PASS. wA.T. (exc. B.S., S.S.,
T.W.) ........................ control ............................ 3928319 1 2.45
68 PASS w/3 -SPD. (exc. H.D.) ...... control ............................ 3928317 1 2.45
68 CORVETTE w/T.H .............. control............................ 3921664 1
68 PASS. (A. T. w /B.S.) ............. control ............................ 3922577 1 2.45
38-39 ALL (exc. col. shift),
40-47 COMM., UTIL.,
48-55 COMM., UTIL. w/4-SPD. (1st Ser.),
55-59 Set. 3 w'4-SPD. (2nd Set.)........ KNOB, gearshift control lever,
39-46 2-SPD. w/mech. shift ............ shift lever (21/, O.D.-black hard
65-68 4/WD w '3-SPD .................. rubber) ............................ 374993 1 .90
40-48 PASS . ......................... KNOB ('/e hole diameter) .............. 3665490 1 1.11
48-53 COMM. w/3-SPD.,
49-52 PASS. (exc. P.G.) ............... KNOB (light ivory) ................... 3699416 1 .87
50-52 PASS. w/P.G . .................. KNOB (light ivory) ................... 3699926 1 .70
53-54 PASS. (exc. P.G.),
54-55 COMM. w/3-SPD. (1st Set.),
55-59 Ser. 3 (2nd Ser.),
57-59 ALL w!H.T.,
60-62 Set. 30 (D-D) w/H.T.,
60-66 D-D w/3-SPD. (exc. 102 W.B.) .... KNOB (1'^6 O,D. x 1"/6 O,L.-black) .... 3718171 1 .92
54-56 ALL w/H.T ..................... KNOB (''e O.D.-black) ................ 3701927 1 .75
55-60 PASS. (exc. 4-SPD.),
60-66 Ser. 10-20, G-10 (exc. 4-SPD.,
D-D),
60-66 Ser. 30 w/3-SPD. H.D., (exc. D-D),
61-66 Set. 10 (D-D) (exc. 4-SPD.) ....... KNOB (213/2 O.L.-black) .............. 3771840 1 .72
55-62 CORVETTE,
63 S.S. w/P.G., 4-SPD. KNOB (white plastic). 3747685 1 2.08
58-63 PASS. w/4-SPD . ................ KNOB (white plastic) ................. 3770344 1 2.08
60-67 Ser. 10 thru 30 w/4-SPD. (exc.
H.D., close ratio),
68 Ser. 10-20 w!4-S PD. (exc. close
ratio, D-D) ................... KNOB (2 O.D.-black plastic) .......... 3761130 1 .95
61-65 PASS. (exc. 4-SPD. S.S., CAPRICE),
61-65 PASS. w 3-SPD . ................ KNOB O.L.-black plastic) ....... 3782694 1 .72
(2743
63 CORVETTE .................... KNOB (black bakelite) ................ 3895202 1 .58
64-68 CORVETTE (exc. A.T.).......... KNOB, control lever .................. 3857160* 1 2.37
*NOTE: On 4-spd. trans. assemblies, it may be necessary to use lever assy. 3857394 w/
a thread length of 5544.
64-67 PASS. w/4-SPD. (exc. B.S.) ...... KNOB, control lever .................. 3857524 1 1.40
64-67 PASS. (4-SPD. w/B.S.)........... KNOB, control lever .................. 3845895 1 2.15
64 CORVETTE w/P.G .............. KNOB, (chromed-plastic) .............. 3820476 1 1.26
65 CAPRICE (exc. 4-SPD.) .......... KNOB, control lever .................. 3877518 1 .98
66 PASS. w'A.T. (exc. CAPRICE),
66 CAPRICE w/A.T. (exc. B.S.)..... KNOB, cont. lever .................... 3790368 1 .72
66 PASS. w 3-SPD. (exc. CAPRICE) . KNOB, cont. lever .................... 3876965 1 .72
66 CAPRICE (exc. 4-SPD., B.S.)..... KNOB, cont. lever .................... 3882907 1 .92
65-67 CORVETTE w/P.G.,
68 CORVETTE w/T.H .............. KNOB, control lever .................. 38779731 i 1 1.64
ttNOTE: In some cases it may be necessary to cut or grind off .0001 from knob end of lever to
allow travel of the button that sets inside the knob to shift into all positions.
67-68 Ser. 30
G-10-20,
67-68 Ser. 10-20 (exc. 4-SPD., D-D),
67-68 Ser. 10 (D-D) (exc. 4-SPD.),
68 Ser. 20 (D-D) w/3-SPD. .......... KNOB, cont. lever .................... 3899961 1 .72
67 CAPRICE w/3-SPD .............. KNOB, cont. lever (black w/chrome) .... 3898251 1 1.15
67 CAPRICE (exc. 4-SPD.,
SPT. CPE.),
67 CAPRICE (SPT. CPE.) w/3-SPD. . KNOB, cont. lever (blue w/chrome) ..... 3898252 1 1.15
67 CAPRICE (STA. WAG.) (exc.
4-SPD.) ...................... KNOB, cont. lever (red w/chrome) ...... 3898253 1 1.15
4.006 x_1967
Chevrolet Motor Division
592 General Motors Corporation
67 CAPRICE (exc. 4-SPD.,
SPT. CPE.),
67 CAPRICE (SPT. CPE.) w/3-SPD. . KNOB, cont. lever (gold w/chrome) ..... 3898255 1 1.1.5
67 PASS. w/3-SPD. (exc. H.D,) ...... KNOB, cont. lever (fawn) .............. 3899061 1 .72
67 PASS. w/3-SPD. (exc. H.D„ S.S.,
................... ..............
CAPRICE) KNOB, cont. lever (blue) 3899062 1 .72
67 IMPALA w/3-SPD. (exc. H.D„
........................ ...............
SED.) KNOB, cont. lever (red) 3899063 1 .72
67 IMPALA (SPT. CPE., CONV.)
.......... ..............
w/3-SPD. (exc. H.D.) KNOB, cont. lever (blue) 3899064 1 .72
67 BEL AIR, IMPALA w/3-SPD.
...................
(exc. H.D,) KNOB, cont. lever (turquoise).......... 3899065 1 .72
..............
67 IMPALA w/3-SPD. (exc. H.D.) .... KNOB, cont. lever (gold) 3899066 1 .72
67 S.S. w/3-SPD.,
.............
67 PASS. (exc. S.S., 4-SPD.) ........ KNOB, cont. lever (black) 3899067 1 .72
67 IMPALA (exc. 4-SPD., CON V.,
..............
STA. WAG., S.S.) KNOB, cont. lever (maroon)............ 3899068 1 .72
.......... .
67 CAPRICE (exc. 4-SPD., STA. WAG.) KNOB, control lever (plum) 3904242 1 1.15
67 Ser. 30 (D-D) w/T.H.,
..................
67 Ser. 20 (D-D) w/3-SPD. (6 cyl.) ... KNOB, control lever 3904736 1 .95
67 Ser. 10 thru 30 w/4-SPD. (close
ratio),
68 Ser. 10-20 (D-D) w/4-SPD.,
..................
68 Ser. 30 w/4-SPD. (exc. close ratio) KNOB, control lever 2455925 1 .85
67 CAPRICE (STA. WAG.) (exc. 4- KNOB, control lever (turquoise
........................ ..................
SPD. ) w/chrome)..... 3898254 1 1.15
68 IMPALA (SPT. CPE) w/3-SPD.
...................
(exc. H.D.) KNOB, control lever (dark teal) ........ 3928278 1 .72
68 CAPRICE w/3-SPD. (exc. H.D. ... KNOB, control lever (med. gray green) .. 3928292 1 1.20
68 PASS. w/3-SPD. (exc. H.D.)...... KNOB, control lever (dark blue w/
chrome) ........................... 3928281 1 1.20
68 IMPALA (CONY.) w/3-SPD. (exc.
........................
H.D.) KNOB, control lever (dark red) ......... 3928276 1 .72
................
68 PASS. w/3-SPD . KNOB, control lever (black w/chrome) .. 3923329 1 1.20
68 STA. WAG. w/3-SPD. (exc. H.D.).. KNOB, control lever (dark saddle w/
chrome) ........................... 3928282 1 1.20
68 PASS. w/3-SPD. (exc. H.D., KNOB, control lever (dark turquoise
.................. w .........................
BISCAYNE) ................ /chrome) 3 92 8283 1 1.20
68 PASS. w/3-SPD . KNOB, control lever (dark gold w/
chrome) ........................... 3928288 1 1.20
................ ..................
68 G-10-20 w/4-S.P.D. ................. KNOB, control lever 3927034 1 2.25
59-63 CORVETTE HANDLE, reverse, w/cable............ 3760085 1 7.75
64-67 PASS., CORVETTE w/4-SPD. .... HANDLE, reverse release lever,
w/retainer & sleeve ................ 3901033A 1 1.30
68 PASS. (A.T. w/B.S.) ............. HANDLE, control lever ............... 3920269 1 5.55
64-65 S.S. w/A. T.,
66-67 SPT. CPE., CONY. w/A.T........ BUTTON, control lever release ........ 3843125 1 .15
66-67 CORVETTE w/P.G.,
68 CORVETTE w /T.H .............. BUTTON, control lever knob ........... 3876439 1 1.11
68 PASS. (A.T. w/B.S.) ............. BUTTON, control lever ............... 3920271 1 .75
47 COE ........................... CABLE, reverse latch (41'/2 O.L.) ...... 3682884 1 2.70
64-67 PASS. w/4-SPD. . . . . . . . . . . . . . . . . CABLE, control reverse release........ 3883686 1 1.55
64 CORVETTE w/4-SPD. (1st design) CABLE, control reverse release
(w/5/32 I.D. x 213/4 O.L. pin at end) .... 3857397A 1 .53
64-66 PASS. (A.T. w/B.S.),
67 S.S. CAPRICE (SPT. CPE., CONY.)
w/A.T . ...................... ROD, control lever pawl............... 3843128 1 1.10
65-68 CORVETTE w/A.T .............. ROD, control lever ................... 3859795 1 9.20
64-67 CORVETTE w/4-SPD............ ROD, control reverse release
(major dia. 7'/32) ..... .............. 3889461A 1 .53
68 PASS. (A.T. w/B.S.) ............. COVER, control lever handle .......... 3920270 1 .75
ANOTE: It may be necessary to enlarge the cable hole in the reverse release handle to 3/33
diameter.
4.008 SMALL PARTS, Gearshift Control Hand Lever
38-55 COMM., UTIL. w/4-SPD. (1st Ser.),
55-59 Ser. 3 w/4-SPD. (2nd Ser.),
60-63 Ser. 10 thru 30 w/4-SPD. (1st
design) ...................... PIN, fulcrum (13/6 O.L.) ............... 590282 2 .05
©-1967
Chevrolet Motor Division 4.006-4.008
General Motors Corporation 593