AV RECEIVER/AV AMPLIFIER

226 Pages·2008·41.94 MB·English

AV RECEIVER/AV AMPLIFIER
RX-V3900/DSP-AX3900
SERVICE MANUAL
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifi cally YAMAHA Products, are already known
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, D
destruction of expensive components, and failure of the product to perform as specifi ed. For these reasons, we advise SPRX
all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or -A-V
IMPORTANT: tThhee a pppreosienntetadt isoenr voicr es raelep roesf etnhtiast imvea.nual to any individual or fi rm does not constitute authorization, certifi cation or X39003900/
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and
specifi cations are subject to change without notice or obligation to retrofi t. Should any discrepancy appear to exist, please contact the
distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
TO SERVICE PERSONNEL ........................................2–3 AMP ADJUSTMENT / アンプ部調整 .............................83
FRONT PANELS .........................................................3–4 DISPLAY DATA .......................................................84–85
REAR PANELS ...........................................................5–8 IC DATA .................................................................86–103
REMOTE CONTROL PANELS .......................................9 BLOCK DIAGRAMS ............................................104–108
SPECIFICATIONS / 参考仕様 .................................10–15 PIN CONNECTION DIAGRAMS ..........................109–111
INTERNAL VIEW ..........................................................16 PRINTED CIRCUIT BOARDS .............................112–143
DISASSEMBLY PROCEDURES / 分解手順 ...........17–25 SCHEMATIC DIAGRAMS ...................................145–170
UPDATING FIRMWARE / REPLACEMENT PARTS LIST ............................171–212
ファームウェアの書き込み .....................................26–29 REMOTE CONTROL ...........................................213–216
SELF-DIAGNOSTIC FUNCTION / ADVANCED SETUP / 本機の設定を変更する ......217–224
ダイアグ（自己診断機能） .......................................30–82
101115 Copyright © 2008 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
animate '08.10
RX-V3900/DSP-AX3900
■ TO SERVICE PERSONNEL
AC LEAKAGE
1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked ⚠ and OUTLET UNDER TEST EQUIVALENT
must be replaced with parts having specifications equal to those
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
INSULATING
that all exposed conductive surfaces are properly insulated
TABLE
from supply circuits.
• Meter impedance should be equivalent to 1500 ohms shunted • Leakage current must not exceed 0.5mA.
by 0.15 μF. • Be sure to test for leakage with the AC plug in both polari-
ties.
“CAUTION”
“F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V
FUSE.”
“F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 4A, 125V
FUSE.”
CAUTION
F1: REPLACE WITH SAME TYPE 10A, 125V FUSE.
F2: REPLACE WITH SAME TYPE 4A, 125V FUSE.
ATTENTION
F1: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 10A, 125V.
F2: UTILISER UN FUSIBLE DE RECHANGE DE MÉME TYPE DE 4A, 125V.
0
V3900/AX390
X-P-
RS
D
WARNING: CHEMICAL CONTENT NOTICE!
This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
About lead free solder / 無鉛ハンダについて
All of the P.C.B.s installed in this unit and solder joints are 本機に搭載されているすべての基板およびハンダ付けに
soldered using the lead free solder. よる接合部は無鉛ハンダでハンダ付けされています。
Among some types of lead free solder currently available, 無鉛ハンダにはいくつかの種類がありますが、修理時に
it is recommended to use one of the following types for は下記のような無鉛ハンダの使用を推奨します。
the repair work.
(cid:12256) Sn+Ag+Cu（錫+銀+銅）
• Sn + Ag + Cu (tin + silver + copper) (cid:12256) Sn+Cu（錫+銅）
• Sn + Cu (tin + copper) (cid:12256) Sn+Zn+Bi（錫+亜鉛+ビスマス）
• Sn + Zn + Bi (tin + zinc + bismuth)
注意：
Caution: 無鉛ハンダの融点温度は通常の鉛入りハンダに比べ30〜
As the melting point temperature of the lead free solder 40℃程度高くなっていますので、それぞれのハンダに合っ
is about 30°C to 40°C (50°F to 70°F) higher than that of たハンダごてをご使用ください。
the lead solder, be sure to use a soldering iron suitable
to each solder.
2
RX-V3900/DSP-AX3900
WARNING: Lithium batteries
CAUTION 注意
Danger of explosion if battery is incorrectly replaced. 正しい電池と交換しないと爆発が起きるおそれがありま
Replace only with the same or equivalent type. す。
同一型名または同等品以外の電池とは絶対に交換しない
ようにしてください。
WARNING: Lithium batteries are dangerous because ADVARSEL!
they can be exploded by improper handling. Observe the Lithiumbatteri –Eksplosionsfare ved fejlagtig håndtering.
following precautions when handling or replacing lithium Udskiftning må kun ske med batteri af samme fabrikat og
batteries. type. Levér det brugte batteri tilbage til leverandøren.
• Leave lithium battery replacement to qualified service
personnel. VARNING
• Always replace with batteries of the same type. Explosionsfara vid felaktigt batteribyte. Använd samma
• When installing on the PC board by soldering, solder batterityp eller an ekvivalent typ som rekommenderas av
using the connection terminals provided on the battery apparattillverkaren. Kassera använt batteri enligt fabrikan-
cells. Never solder directly to the cells. Perform the tens instruktion.
soldering as quickly as possible.
• Never reverse the battery polarities when installing. VAROITUS
• Do not short the batteries.
Paristo voi räjähtää, jos se on virheellisesti asennettu.
• Do not attempt to recharge these batteries.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
• Do not disassemble the batteries.
tyyppiin. Hävitä käytetty peristo valmistajan ohjeiden mu-
D
• Never heat batteries or throw them into fire. SR
kaisesti. PX
-A-V
X39003900/
■ FRONT PANELS
RX-V3900 (U, C models)
U model
C model
3
RX-V3900/DSP-AX3900
RX-V3900 (R, T, K, A, B, G, E, L models)
0 DSP-AX3900 (J model)
V3900/AX390
X-P-
RS
D
4
RX-V3900/DSP-AX3900
■ REAR PANELS
RX-V3900 (U model)
RX-V3900 (C model)
D
SR
PX
-A-V
X39003900/
RX-V3900 (R model)
5
RX-V3900/DSP-AX3900
RX-V3900 (T model)
RX-V3900 (K model)
0
V3900/AX390
X-P-
RS
D
RX-V3900 (A model)
6
RX-V3900/DSP-AX3900
RX-V3900 (B model)
RX-V3900 (G, E models)
D
SR
PX
-A-V
X39003900/
RX-V3900 (L model)
7
RX-V3900/DSP-AX3900
DSP-AX3900 (J model)
0
V3900/AX390
X-P-
RS
D
8
RX-V3900/DSP-AX3900
■ REMOTE CONTROL PANELS
RAV386 RAV388 RAV387
RX-V3900 (U, C models) RX-V3900 (R, T, K, A, B, G, E, L models) DSP-AX3900 (J model)
D
SR
PX
-A-V
X39003900/
RAV36
RX-V3900 (U, C, R, T, K, A, B, G, E, L models)
9
RX-V3900/DSP-AX3900
■ SPECIFICATIONS / 参考仕様
■ Audio Section / オーディオ部
Minimum RMS Output Power (Power Amp. Section) / RIAA Equalization Deviation / RIAA偏差 (20 Hz to 20 kHz)
定格出力 (パワーアンプ部) (20 Hz to 20 kHz) PHONO (MM) ...................................................................0 ±0.5 dB
FRONT L/R Total Harmonic Distortion / 全高調波歪率 (20 Hz to 20 kHz)
U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms)
PHONO (MM) to REC OUT (1 V) ................................0.02 % or less
.............................................................................140 W + 140 W
CD, etc. to FRONT L/R SP OUT (70 W, 8 ohms) ........0.04 % or less
J model (0.06 % THD, 6 ohms) ..............................140 W + 140 W
CENTER Signal to Noise Ratio / 信号対雑音比 (IHF-A network)
PHONO (MM) (Input shorted) to SP OUT
U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms)
U, C, R, T, K, L models (5 mV) ................................86 dB or more
...........................................................................................140 W
A, B, G, E models (5 mV) ........................................81 dB or more
J model (0.06 % THD, 6 ohms) ............................................140 W
J model (2.5 mV) .....................................................80 dB or more
SURROUND L/R
CD, etc. (Input shorted) to SP OUT
U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms)
250 mV ..................................................................100 dB or more
.............................................................................140 W + 140 W
J model (0.06 % THD, 6 ohms) .............................140 W + 140 W Residual Noise / 残留ノイズ (IHF-A network)
SURROUND BACK L/R FRONT L/R SP OUT ...................................................150 μV or less
U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) Channel Separation / チャンネルセパレーション (1 kHz/10 kHz)
.............................................................................140 W + 140 W PHONO (Input shorted) .....................60 dB or more/55 dB or more
J model (0.06 % THD, 6 ohms) ..............................140 W + 140 W CD, etc. (Input 5.1 k-ohms shorted) ...60 dB or more/45 dB or more
Maximum Power / 実用最大出力 (JEITA, 1 kHz, 10 % THD) Tone Control Characteristics / トーンコントロール特性
FRONT L/R BASS
R, T, K, L models (8 ohms) .....................................185 W + 185 W Boost/Cut .................................................................±6 dB (50 Hz)
J model (6 ohms) ...................................................185 W + 185 W Turnover frequency .............................................................350 Hz
CENTER TREBLE
R, T, K, L models (8 ohms) ...................................................185 W Boost/Cut ...............................................................±6 dB (20 kHz)
J model (6 ohms) .................................................................185 W Turnover frequency ............................................................3.5 kHz
SURROUND L/R
ZONE2, ZONE3 Tone Control Characteristics
R, T, K, L models (8 ohms) .....................................185 W + 185 W
0 [U, C, R, T, K, A, B, G, E, L models]
X-V3900/P-AX390 SJRU ,Rm TRo, OdKeU, lL N( 6mD o oBhdAmeClssK) ( 8.L. ./o.R.h..m...s..). . ..........................................................................118855 WW ++ 118855 WW BBTAuoSronSsotv/Ceru tf r e..q..u..e..n..c..y.. . .........................................................................................±..1..0.. .d..B... .(.140500 H Hzz)
RS J model (6 ohms) ...................................................185 W + 185 W
D TREBLE
Dynamic Power Per Channel (IHF) Boost/Cut ...........................................................±10 dB (10 kHz)
FRONT L/R (8/6/4/2 ohms) Turnover frequency ..........................................................2.0 kHz
U, C, R, T, K, A, L models ...............................170/205/265/345 W
Filter Characteristics / フィルター特性
Max. Power Per Channel (1 kHz, 0.7 % THD, 4 ohms) FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.)
[B, G, E models] ....................fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct.
FRONT L/R .............................................................200 W + 200 W SUBWOOFER (L.P.F.)
CENTER ...............................................................................200 W .....................fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct.
SURROUND L/R .....................................................200 W + 200 W
SURROUND BACK L/R ..........................................200 W + 200 W ■ Video Section / ビデオ部
Dynamic Headroom [U, C, R, T, K, A, L models] Video Signal Type / ビデオ信号方式
8 ohms .................................................................................0.84 dB Monitor out (Wall paper) / モニターアウト（壁紙）
IEC Power (1 kHz, 0.04 % THD, 8 ohms) [B, G, E models] U, C, R, K, J models .......................................................NTSC/PAL
FRONT L/R ...............................................................145 W + 145 W T, A, B, G, E, L models ...................................................PAL/NTSC
Video conversion / ビデオコンバージョン
Damping Factor / ダンピングファクタ (1 kHz, 8 ohms)
.......................................................................................NTSC/PAL
FRONT L/R ....................................................................150 or more
Zone out (Gray back)
Input Sensitivity/Input Impedance / 入力感度／入力インピーダンス U, C, R, K models .................................................................NTSC
(1 kHz, 100 W/8 ohms) T, A, B, G, E, L models .............................................................PAL
PHONO (MM) ..................................................3.5 mV / 47 k-ohms
Composite Video Signal Level / コンポジットビデオ信号
CD, etc. ..........................................................200 mV / 47 k-ohms
..............................................................................1 Vp-p / 75 ohms
MULTI CH INPUT
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER S-Video Signal Level / Sビデオ信号
....................................................................200 mV / 47 k-ohms Y ............................................................................1 Vp-p / 75 ohms
C (NTSC) .......................................................0.286 Vp-p / 75 ohms
Maximum Input Signal Level / 最大許容入力
(PAL) ..............................................................0.3 Vp-p / 75 ohms
PHONO (MM) (1 kHz, 0.1 % THD) ............................60 mV or more
CD, etc. (1 kHz, 0.5 % THD) .......................................2.4 V or more Component Video Signal Level / コンポーネントビデオ信号
Y ............................................................................1 Vp-p / 75 ohms
Output Level/Output Impedance / 出力電圧／出力インピーダンス
Pb/Pr ..................................................................0.7 Vp-p / 75 ohms
REC OUT ...........................................................200 mV / 900 ohms
PRE OUT (FRONT L/R, CENTER, SURROUND L/R, Maximum Input Level / 最大許容入力
SURROUND BACK L/R) ......................................1.0 V / 500 ohms VIDEO CONV. OFF ................................................1.5 Vp-p or more
SUBWOOFER (20 Hz) .........................................1.0 V / 1.2 k-ohms Signal to Noise Ratio / 信号対雑音比
[U, C, R, T, K, A, B, G, E, L models] VIDEO CONV. OFF ....................................................60 dB or more
ZONE 2 OUT .....................................................1.0 V / 1.4 k-ohms
Monitor Out Frequency Response / モニターアウト周波数帯域
ZONE 3 OUT .....................................................1.0 V / 1.4 k-ohms
(VIDEO CONV. OFF)
Headphone Jack Rated Output/Impedance / Component video signal ..........................5 Hz to 100 MHz, ±3 dB
ヘッドフォン出力／出力インピーダンス (1 kHz, 40 mV, 8 ohms) [J model]
CD, etc. .............................................................150 mV / 100 ohms D5-video signal ......................................5 Hz to 100 MHz, ±3 dB
Frequency Response / 周波数特性 (10 Hz to 100 kHz)
CD, etc. to FRONT L/R (Pure direct) ..................................+0/-3 dB
10