aluminum - CRL-ARCH

48 Pages·2012·6.27 MB·English

01-B2
STOREFRONTS
ALUMINUM
Table of Contents Flush Front™
• Series FF450
• Series FF451
• Series FT451
• Series FF600
B
• Series FF601
• Series FT601
SECTION B2 PAGE
Series FF450, FF451, FT451, FF600, FF601, and FT601
SPECIFICATIONS..................................................................................................................................02-B2 and03-B2
TECHNICAL DATA....................................................................................................................................................04-B2
SPECIAL FEATURES................................................................................................................................................05-B2
Series FF450
TYPICAL DETAILS ................................................................................................................................06-B2 thru11-B2
WINDLOAD CHARTS ............................................................................................................................12-B2 and13-B2
DEADLOAD CHARTS ..............................................................................................................................................14-B2
Series FF451 and FT451
TYPICAL DETAILS ................................................................................................................................15-B2 thru21-B2
WINDLOAD CHARTS ............................................................................................................................22-B2 and23-B2
DEADLOAD CHARTS ..............................................................................................................................................24-B2
Series FF600
TYPICAL DETAILS ................................................................................................................................25-B2 thru29-B2
WINDLOAD CHARTS ............................................................................................................................30-B2 and31-B2
DEADLOAD CHARTS ..............................................................................................................................................32-B2
Series FF601 and FT601
TYPICAL DETAILS ................................................................................................................................33-B2 thru39-B2
WINDLOAD CHARTS ............................................................................................................................40-B2 and41-B2
DEADLOAD CHARTS ..............................................................................................................................................42-B2
ACCESSORIES AND GLAZING GASKETS (ALL SYSTEMS)................................................................43-B2 thru45-B2
MISCELLANEOUS FRAMING................................................................................................................46-B2 thru48-B2
Due to the diversity in state/provincial, local, and federal laws and codes that govern the design and application of architectural products, it is
the responsibility of the individual architect, owner, and installer to ensure that products selected for use on projects comply with all applicable
building codes and laws. U.S. Aluminum exercises no control over the use or application of its products, glazing materials, and operating
hardware, and assumes no responsibility thereof.
The rapidly changing technology within the architectural aluminum products industry demands that U.S. Aluminum reserve the right
to revise, discontinue or change any product line, specification or electronic media without prior written notice.
NOTE:Dimensions in parentheses ( ) are millimeters unless otherwise noted.
Other metric units shown in this publication are:
m - meter Kg - kilogram
Pa - pascal KPa - kilopascal
MPa - megapascal
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
02-B2
STOREFRONTS
ALUMINUM
Specifications Flush Front™
• Series FF450
SECTION 08 41 13 ALUMINUM FRAMED STOREFRONTS • Series FF451
• Series FF600
• Series FF601
B
SERIES FACE WIDTH DEPTH GLAZING INFILL GLAZING METHOD
FF450 1-3/4" (44.5) 4-1/2" (114.3) 1/4" (6) or 3/8" (10)
FF451 2" (50.8) 4-1/2" (114.3) 1" (25)
Exterior/Interior
FF600 1-3/4" (44.5) 6" (152.4) 1/4" (6) or 3/8" (10)
FF601 2" (50.8) 6" (152.4) 1" (25)
I. GENERAL DESCRIPTION water penetration at test pressure of A Fluoropolymer paint coating
Work Included: Furnish all necessary 8 psf (384 Pa) when tested with the conforming with the requirements of
materials, labor, and equipment for the high performance subsill. AAMA 2605. Color shall be (Specify a
complete installation of aluminum Structural Performance:shall be U.S. Aluminum standard color).
framing as shown on the drawings and tested in accordance with ASTM E 330
specified herein. (Specifier Note: and based on: FABRICATION
It is suggested that related items such • Maximum deflection of L/175 of the The framing system shall provide for
as aluminum entrance doors, glass, span flush glazing on all sides with no
and sealants be included whenever • Allowable stress with a safety factor projecting stops. Vertical and
possible). of 1.65 horizontal framing members shall have
Work Not Included: Structural support The system shall perform to this a nominal face dimension of (Specify).
of the framing system, interior criteria under a windload of (Specify) Overall depth shall be (Specify).
closures, trim. (Specifier list other psf. Entrance framing members shall be
exclusions). Testing Procedures - compatible with glass framing in
Related Work Specified Elsewhere: ASTM 283, E 331, and E 330 - appearance. Provide for internal
(Specifier list). Laboratory performance testing. drainage of infiltrated water into an
AAMA 503-08 - Newly installed extruded aluminum subsill channel
QUALITY ASSURANCE storefronts. AAMA 511-08 - Installed where it is drained to the exterior
Drawings and specifications are storefronts after six months. through weep slots.
based on the Series (Specify) Flush
Front™ System as manufactured by II. PRODUCTS MATERIALS III. EXECUTION INSTALLATION
U.S. Aluminum. Whenever substitute Extrusions shall be 6063-T5 alloy and All glass framing shall be set in correct
products are to be considered, temper (ASTM B221 alloy T5 temper). locations as shown in the details and
supporting technical literature, Fasteners, where exposed, shall be shall be level, square, plumb, and in
samples, drawings, and performance aluminum, stainless steel or zinc alignment with other work in
data must be submitted 10 days plated steel in accordance with ASTM accordance with the manufacturer’s
prior to bid in order to make a valid A 164. Perimeter anchors shall be installation instructions and approved
comparison of the products involved. aluminum or steel, providing the steel shop drawings. All joints between
Test reports certified by an is properly isolated from the aluminum. framing and the building structure shall
independent test laboratory must be Glazing gaskets shall be E.P.D.M. be sealed in order to secure a
made available upon request. elastomeric extrusions. watertight installation.
PERFORMANCE REQUIREMENTS FINISH PROTECTION AND CLEANING
Air Infiltration:shall be tested in All exposed framing surfaces shall be After installation the General
accordance with ASTM E 283. free of scratches and other serious Contractor shall adequately protect
Infiltration shall not exceed .06 cfm blemishes. Aluminum extrusions shall exposed portions of aluminum
per square foot (.0003m3/sm2) of be given a caustic etch followed by surfaces from damage by grinding and
fixed area when tested at 6.24 psf an anodic oxide treatment to obtain… polishing compounds, plaster, lime,
(300 Pa). (Specify one of the following): acid, cement or other contaminants.
Water Infiltration:shall be tested in _____#11 Clear anodic coating The General Contractor shall be
accordance with ASTM E 331. No _____#22 Dark Bronze anodic coating responsible for final cleaning.
_____#33 Black anodic coating
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
03-B2
STOREFRONTS
ALUMINUM
Specifications Thermal Flush Front™
• Series FT451
SECTION 08 41 13 ALUMINUM FRAMED STOREFRONTS • Series FT601
SERIES FACE WIDTH DEPTH GLAZING INFILL GLAZING METHOD
B
FT451 4-1/2" (114.3)
2" (50.8) 1" (25) Exterior/Interior
FT601 6" (152.4)
I. GENERAL DESCRIPTION • Allowable stress with a safety factor anodic oxide treatment to obtain…
Work Included: Furnish all necessary of 1.65 (Specify one of the following):
materials, labor, and equipment for the The system shall perform to this _____#11 Clear anodic coating
complete installation of aluminum criteria under a windload of (Specify) _____#22 Dark Bronze anodic coating
framing as shown on the drawings and psf. Structural Integrity - Manufacturer _____#33 Black anodic coating
specified herein. (Specifier Note: It is shall provide a Two Year Warranty on A Fluoropolymer paint coating
suggested that related items such as thermal framing against failure. conforming with the requirements of
aluminum entrance doors, glass, and Thermal Performance - Series AAMA 2605. Color shall be (Specify
sealants be included whenever FT451/FT601 shall be tested in a U.S. Aluminum standard color).
possible). accordance with NFRC 100, 200,
Work Not Included: Structural support and AAMA 1503. FABRICATION
of the framing system, interior The system shall perform to this The framing system shall provide for
closures, trim. (Specifier list other criteria under a windload of (Specify) flush glazing on all sides with no
exclusions). psf. projecting stops. Vertical and
Related Work Specified Elsewhere: Testing Procedures - horizontal framing members shall have
(Specifier list). ASTM 283, E 331, and E 330 - a nominal face dimension of 2" (50.8).
Laboratory performance testing. Overall depth shall be (Specify).
QUALITY ASSURANCE AAMA 503-08 - Newly installed Entrance framing members shall be
Drawings and specifications are based storefronts. AAMA 511-08 - Installed compatible with glass framing in
on the Series (Specify)Thermal Flush storefronts after six months. appearance. Provide for internal
Front™System as manufactured by drainage of infiltrated water into an
U.S. Aluminum. Whenever substitute II. PRODUCTS MATERIALS extruded aluminum subsill channel
products are to be considered, Extrusions shall be 6063-T5 alloy and where it is drained to the exterior
supporting technical literature, temper (ASTM B221 alloy T5 temper), through weep slots.
samples, drawings, and performance thermally broken by a two part
data must be submitted 10 days chemically cured high density III. EXECUTION INSTALLATION
prior to bid in order to make a valid polyurethane. To ensure that All glass framing shall be set in correct
comparison of the products involved. composite strength remains unaltered locations as shown in the details and
Test reports certified by an during thermal cycling, a mechanical shall be level, square, plumb, and in
independent test laboratory must be bond between the aluminum and the alignment with other work in
made available upon request. thermal filling shall be created by accordance with the manufacturer’s
mechanically abrading the extrusion installation instructions and approved
PERFORMANCE REQUIREMENTS thermal cavity prior to filling with the shop drawings. All joints between
Air Infiltration:shall be tested in polyurethane polymer. Fasteners, framing and the building structure shall
accordance with ASTM E 283. where exposed, shall be aluminum, be sealed in order to secure a
Infiltration shall not exceed .06 cfm per stainless steel or zinc plated steel in watertight installation.
square foot (.0003m3/sm2) of fixed area accordance with ASTM A 164.
when tested at 6.24 psf (300 Pa). Perimeter anchors shall be aluminum
Water Infiltration:shall be tested in or steel, providing the steel is properly PROTECTION AND CLEANING
accordance with ASTM E 331. No isolated from the aluminum. Glazing After installation the General
water penetration at test pressure of 8 gaskets shall be E.P.D.M. elastomeric Contractor shall adequately protect
psf (384 Pa). When tested with the extrusions. exposed portions of aluminum
high performance subsill. surfaces from damage by grinding and
Structural Performance:shall be FINISH polishing compounds, plaster, lime,
tested in accordance with ASTM E All exposed framing surfaces shall be acid, cement, or other contaminants.
330 and based on: free of scratches and other serious The General Contractor shall be
• Maximum deflection of L/175 of the blemishes. Aluminum extrusions shall responsible for final cleaning.
span be given a caustic etch followed by an
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
04-B2
STOREFRONTS
ALUMINUM
Technical Data Flush Front™
• Series FF450
• Series FF451
Flush Front™Systems feature screw race joinery and panel type installation, which allows for
• Series FT451
shop or job site fabrication. Injection molded water deflectors at intermediate horizontals, and a
• Series FF600
B continuous sill gutter with factory pre-punched weep slots, ensure control of any infiltrated water.
• Series FF601
The plane of the glass may be reversed from exterior to interior or any combination to give these
• Series FT601
standard systems a custom look. Flush Front™Series FT451 and FT601 offer improved thermal
performance using the Poly-Aluminizer™thermal break technology as described on page 44-B1.
All series may be glazed from the interior or exterior using a top load E.P.D.M. glazing gasket,
see page 01-B3. This multi-purpose product was also designed and tested for use as a Window
Wall System, and is an ideal choice for fixed horizontal ribbon window applications. Flush Front
Systems accommodate most U.S. Aluminum Entrance Doors.
FLUSH FRONT
SERIES WIDTH DEPTH GLAZING INFILLS APPLICATION
FF450 1-3/4" (44.5) 4-1/2" (114.3) 1/4" (6) or 3/8" (10)
FF451 2" (50.8) 4-1/2" (114.3) 1" (25)
Ground Floor to
FT451 (Thermal) 2" (50.8) 4-1/2" (114.3) 1" (25) Mid-Rise Buildings.
Ideal for Fixed
FF600 1-3/4" (44.5) 6" (152.4) 1/4" (6) or 3/8" (10) Horizontal Ribbon
Windows.
FF601 2" (50.8) 6" (152.4) 1" (25)
FT601 (Thermal) 2" (50.8) 6" (152.4) 1" (25)
GLASS SIZES*
Series FF450 and FF600
= Daylight Opening + 5/8" (15.9)
for 1/4" (6) Glass
Series FF451, FT451, FF601, and FT601
= Daylight Opening + 7/8" (22.2)
for 1" (25) Glass
* These formulae do not take into account glass tolerances. Consult glass manufacturer before ordering glass.
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
05-B2
STOREFRONTS
ALUMINUM
Special Features Flush Front™
• Series FF450
Flush Front™Systems allow the plane • Series FF451
of the glass to be reversed from exterior • Series FT451
to interior or any combination to give • Series FF600 B
these standard systems a custom look. • Series FF601
Flush Front™is ideal for use in storefront • Series FT601
and punched opening or ribbon window
applications. Flush Front™Systems
accommodate most U.S. Aluminum
Entrance Doors.
System features screw race joinery with
split vertical mullions which allows for
framing to be shop fabricated and shipped
to the job site partially or totally assembled
into panels. The assembled panel units are
then snapped together into long runs.
Subsills with factory pre-punched weep
slots must be used with these systems.
Apply silicone to two sides of glazing pocket at vertical/horizontal
joint and glazing reglets. Slide water deflector, down into position.
Seal over top edges of water deflector, leaving a gap on outside
edge allowing water to drain into subsill.
Water Deflector
Stretch "W" Block and slide it between glass
and mullion into deep glazing pocket. Push it all
"W" Edge Block
the way until it clears glass and locks into place.
These blocks are used to prevent glass from
"walking" out of the pocket caused by extreme
vibration or minor earthquakes.
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
06-B2
STOREFRONTS
ALUMINUM
Typical Details Flush Front™
• Series FF450
FLUSH OUT
FOR 1/4" (6) OR 4
B
3/8" (10) GLAZING
NOTE:NP225E.P.D.M. Glazing
1 2 3
Gaskets used on both sides
5
of 1/4" (6) glass throughout.
NP238E.P.D.M. Glazing
NOTE:Part numbers shown are Gaskets for 3/8" (10) glazing.
available in 24' (7.3 m) stock lengths.
Visit usalum.comfor more information. 6
TYPICAL ELEVATION
EC480Subsill's SS452Optional SS469Optional
End Closure (Typ.) Steel Stiffener Steel Stiffener
FF452 FF452 FF469
4-1/2"
PF100
(114.3)
RF200 FF460
1-3/4" D.L.O. 1-3/4" D.L.O. 1-3/4" D.L.O.
(44.5) (44.5) (44.5)
1/4" (6.4) FRAME WIDTH
Min.
ROUGH OPENING
1 2 3
1/2"
(12.7) HC200
Optional Head Anchor
1-3/4" FF473 FF473
(44.5)
M-473 M-473
O. 4 4
NG T D.L.
NI GH
PE EI FH463 M-875 FH453
O H 1-3/4"
GH ME (44.5)
U A
RO FR M-473 5 5
O.
L.
D.
FF482 6 FF483 6
1-3/4" M-875
FF400 FF400
(44.5)
Weep Slot
1/4" (6.4)
Min. Interior Glazing Exterior Glazing
NOT TO SCALE
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
07-B2
STOREFRONTS
ALUMINUM
Typical Details Flush Front™
• Series FF450
FLUSH IN
FOR 1/4" (6) OR
3/8" (10) GLAZING B
4
1 2 3 NOTE:NP225E.P.D.M. Glazing
Gaskets used on both sides
NOTE:Part numbers shown are 5
of 1/4" (6) glass throughout.
available in 24' (7.3 m) stock lengths.
NP238E.P.D.M. Glazing
Visit usalum.comfor more information.
Gaskets for 3/8" (10) glazing.
6
TYPICAL ELEVATION
EC480Subsill's
End Closure
FF452 FF452 FF469 4-1/2"
(114.3)
PF100 RF200 FF460
SS452Optional SS469Optional
1-3/4" 1-3/4" Steel Stiffener 1-3/4" Steel Stiffener
(44.5) D.L.O. (44.5) D.L.O. (44.5) D.L.O.
1/4" (6.4) FRAME WIDTH
Min.
ROUGH OPENING
1 2 3
1/2" HC200
(12.7) Optional Head Anchor
FF473
1-3/4"
(44.5)
M-473
4
O.
L.
G D.
N T
NI GH
OPE HEI 1-3/4" FH463
H E (44.5)
G M
U A
O R M-473 5
R F O.
L.
D.
6
FF482
FF400
1-3/4"
(44.5)
1/4" (6.4) Exterior Glazing
Min.
NOT TO SCALE
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
08-B2
STOREFRONTS
ALUMINUM
Typical Details Flush Front™
• Series FF450
FLUSH IN / FLUSH OUT
FOR 1/4" (6) OR
B 3/8" (10) GLAZING 5 8
1 2 3 2 4
NOTE:Part numbers
6 9
shown are available in
24' (7.3 m) stock lengths. NOTE:NP225E.P.D.M. Glazing
Visit usalum.comfor Gaskets used on both sides
more information. of 1/4" (6) glass throughout.
7 10
NP238E.P.D.M. Glazing
Gaskets for 3/8" (10) glazing.
TYPICAL ELEVATION
EC480Subsill's
End Closure
FF452 FF452 FF452 4-1/2" FF469
PF100 (114.3)
RF200 RF200 FF460
1-3/4" D.L.O. 1-3/4" D.L.O. 1-3/4" D.L.O. 1-3/4"
(44.5) (44.5) (44.5) (44.5)
1/4" (6.4)
FRAME WIDTH
Min.
ROUGH OPENING
1 2 3 4
1/2"
HC200
(12.7)
Optional Head Anchor
1-3/4" FF473 FF473
(44.5)
M-473 M-473
5 8
O.
L.
G D.
N T
NI GH
PE EI 1-3/4" FH453 FH463
O H
H E (44.5)
G M
U A
RO FR 6 M-473 9
O.
L.
D. FF483 7 FF482 10
1-3/4" FF400 FF400
(44.5)
1/4" (6.4)
Min. Exterior Glazing
NOT TO SCALE
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
09-B2
STOREFRONTS
ALUMINUM
Typical Details Flush Front™
• Series FF450
DOOR FRAMING
5
NOTE:Doors are available in stock to B
accommodate 36" x 84" (914 x 2134) and
72" x 84" (1829 x 2134) door openings. 1 2
NOTE:NP225E.P.D.M. Glazing
Visit usalum.comfor more information.
Gaskets used on both sides
6 of 1/4" (6) glass throughout.
3 4 NP238E.P.D.M. Glazing
Gaskets for 3/8" (10) glazing.
7
CENTER HUNG DOOR
1/2"
(12.7)
PF100Filler (Typ.)
FF436 FF436
1-3/4"
JS463
(44.5)
RF200
5 M-453
20101M17
O. Center Hung
L. Closer
D.
3/16" 105° N.H.O.
D.L.O. (4.8) M-122/ M-122/
M-123 M-123
1 2 2-1/2"
(63.5) 1-3/4"
(44.5)
FF436/ FF436/ JC457/ Center J-450
P-050 P-050 P-427 Pivot Top
T D-201 D-201
H Portion
RF200 G
EI
M-550 H
E M-550 M-550
D-300 M
A
R
F
6 6
1/8" 1/8"
(3.2) (3.2)
1-3/4" D.O. 1-3/4" O.
(44.5) (44.5) D.
FRAME WIDTH M-550 M-550
7 7
3 4
D-101 D-101
3/16"
(4.8)
TH014Threshold TH017Threshold
1/2"
(Use With Floor Closers)
(12.7)
NOT TO SCALE
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2
10-B2
STOREFRONTS
ALUMINUM
Typical Details Flush Front™
• Series FF450
DOOR FRAMING
5 8
B NOTE:Doors are available 1 2 1 2
in stock to accommodate
36" x 84" (914 x 2134) and
6 9
72" x 84" (1829 x 2134)
door openings. Visit 3 4 3 4 NOTE:NP225E.P.D.M. Glazing
Gaskets used on both sides
usalum.comfor
of 1/4" (6) glass throughout.
more information.
NP238E.P.D.M. Glazing
7 7
Gaskets for 3/8" (10) glazing.
OFFSET HUNG DOORS
1/2"
(12.7)
PF100Filler (Typ.)
FF436 FF436
1-3/4"
FF473 FF473
P-050 P-050 (44.5)
RF200
I-425/ 5 M-473 M-473
I-459
O.
L.
D. 3/4" I-425/ I-425/ C2lo1s2e0r1 WUith
D.L.O. (19.1) I-459 I-459 Offset Arm
105° N.H.O.
1 2
2-1/2"
(63.5) 1-3/4"
(44.5)
T
H
FF436/ FF436/ G J-450
DS047 DS047 EI 1/8" DS037/ DA201
H (3.2)
RF200 ME D-201 MC037
A
R M-550 D-101
F
M-550
M-550
DT550 6
3/32" 3/32"
(2.4) (2.4) O.
D.
1-3/4" D.O. 1-3/4"
(44.5) (44.5)
Door Sweep Door Sweep
FRAME WIDTH 7 With With
Concealed Concealed
Fasteners Fasteners
3 4
D-101 D-101
3/16" 3/16"
(4.8) BW200 (4.8) BW200
TH250 TH250
1/2" 1/2"
(12.7) (12.7)
NOT TO SCALE
Online usalum.com By Phone [phone]
Online crlaurence.com By Phone [phone]
B2