Advances in Polymer Technology 1997: Vol 16 Table of Contents

5 Pages·1997·1.5 MB·English

Advances in
The Polymer Processing Institute (PPI) is an in-
dependent research corporation headquartered
at Stevens Institute of Technology with labora-
tories at Stevens and the NJ Institute of Technol-
ogy. Its mission is to serve industry by advancing
the scientific underpinnings of polymer technol-
ogy through industry-sponsored research, de-
velopment, and education, and to disseminate
information pertaining thereto via all appropriate
Journal of the Polymer Ppr ocessing Institute mechanisms for technology transfer.
Contents of
Volume 16
Number 1, Spring 1997
Of rEATURES
Analysis of Morphology Development of Immiscible Blends in a Twin Screw
Extruder |
Oliver Franzheim, M. Stephan, T. Rische, P. Heidemeyer, U. Burkhardt, and A. Kiani
The Effect of Multiple Extrusion Passes During Recycling of High Density
Polyethylene if
A. T. P. Zahavich, B. Latto, E. Takacs, and J. Viachopoulos
Experimental Analysis of the Kneading Disk Region in a Co-Rotating Twin
Screw Extruder: Part 2. Glass-Fiber Degradation During Compounding 25
Y. Shimizu, S. Arai, T. Itoyama, and H. Kawamoto
Long-Term Performance of a Polymer Composite Repair System for Gas
Pipelines 33
R. Frassine
Modeling the Transient Flow of Rubber Compounds in the Dispersive Section
of an Internal Mixer with Slip-Stick Boundary Conditions 45
M. H. R. Ghoreishy and V. Nassehi
B be PARTMENTS
News of the Polymer Processing Institute 69
VOLUME CONTENTS
Technical Books
Announcements
Number 2, Summer 1997
@ FEATURES
Radical Polymerization of Styrene and Styrene-Butyl Methacrylate in a
Counterrotating Twin Screw Extruder
A. J. van der Goot and L. P. B. M. Janssen
Velocity Measurements in the Nip Region of a Co-Rotating Twin-Screw
Extruder Using Laser Doppler Anemometry
M. V. Karwe, S. Bakalis, and V. Sernas
Analysis of Open-Ended Injection Molding
T. Zhang, J. R. G. Evans, and M. J. Bevis
Evaluation of the Effect of Processing Parameters on the Properties of
Advanced Styrenic Resins: A Design of Experiments Approach
T. P. Skourlis, B. Mohapatra, C. Chassapis, and S. Manoochehri
Effect of Processing Parameters on the Compression Resistance of a Plug-
Assist Vacuum Thermoformed Container
A. Aroujalian, M. O. Ngadi, and J.-P. Emond
B SPECIAL REPORT
Blends of High-Density Polyethylene with Homogeneous Long-Chain
Branched Polyethylenes
J. Schellenberg
§ DEPARTMENTS
News of the Polymer Processing Institute
Announcements
VOLUME CONTENTS
Number 3, Fall 1997
O rEATURES
Structural Analysis for Gas-Assisted Injection-Molded Parts
Y. Y. Nie, L. S. Turng, and K. K. Wang
Flow Visualization of the Gas-Assisted Injection Molding Process
S. Y. Yang, S. J. Liou, and W. N. Liou
Process Analysis of Resin Transfer Molding with Autoclave-Assisted
Laminate Consolidation
Seong Woo Kim, Ki-Jun Lee, J. C. Seferis, and Jae-Do Nam
Measurement of Elongation Viscosity for Polymer Melts by Fiber Spinning
Gwo-Geng Lin and Ming-Chong Hu
Simulation of Rheological Behavior of Polymer Blends by Finite Element
Analysis
J. Zhao, L. Mascia, and V. Nassehi
Characterization of a Fiber Reinforced Semirigid Liquid Crystalline Polymer
G. Sortino, R. Scaffaro, and F. P. La Mantia
z DEPARTMENTS
News of the Polymer Processing Institute
Number 4, Winter 1997
O PEATURES
Compounding with Single-Screw Extruders
Martin Gale
Structure Development and Control of Injection-Molded Hydroxylapatite-
Reinforced Starch/EVOH Composites
R. L. Reis, A. M. Cunha, P. S. Allan, and M. J. Bevis
Scaling Issues in Resistance-Welded Thermoplastic Composite Joints
Steven H. McKnight, Scott T. Holmes, John W. Gillespie, Jr., Cynthia L. T. Lambing, and
James M. Marinelli
VOLUME CONTENTS
Rheological Characteristics and Cure Kinetics of EPON 862/W Epoxy Used in
Pultrusion
R. Shanku, J. G. Vaughan, and J. A. Roux
Recycling of Polypropylene-Based Composites
J. G. Poulakis, P. C. Varelidis, and C. D. Papaspyrides
Reactive Blending of Ethylene-Methylacrylate Copolymer and Poly-Dimethyl
Siloxane Rubber: Kinetics Studies from Infrared Spectroscopy
Subhra Mohanty, Robin N. Santra, and Golok B. Nando
Short Communication—In-Situ Composite Based on Polypropylene and
Nylon6
Xuedong Li, Mingcai Chen, Yuhui Huang, Guo Lin, Shulu Zhao, Bing Liao, Chuangqing Wang, and
Guangmin Cong
beD EPARTMENTS
News of the Polymer Processing Institute